Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › from 2016.01
RM3270E _58 Vehicle Interior _041713 HEATING / AIR CONDITIONING _0199983 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 87211B 1.INSTALL NO. 3 AIR DUCT

a.
E316350

Attach the claw to install the No. 3 air duct.


Hide 2.INSTALL AIR CONDITIONING UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Temporarily install the air conditioning unit assembly and instrument panel reinforcement assembly with the nut.

E319751C01
5.625,3.542 5.771,3.542 5.771,3.542 5.833,3.219 true 5.448,3.458 5.76,3.615 0.313,0.156 10 false *a
*a Standard Position - -



b.

Align the standard position, install the drain cooler hose.


c.

Tighten the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55950G 3.INSTALL DEFROSTER NOZZLE ASSEMBLY

E317580

a.

Attach the claw to install the defroster nozzle assembly.


Hide 55330B 4.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

for Automatic Transmission:

Install the 11 bolts.

E319742C01
3.417,1.021 3.729,1.177 0.313,0.156 10 true *A
*A for Manual Transmission - -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D


Torque:
Bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

for Manual Transmission:

Install the 12 bolts.

Torque:
Bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)


c.
E325412C01
0.063,0.073 0.375,0.229 0.313,0.156 10 true *A
*A for Driver Side


Install 2 new hole plugs.


Hide 55306A 5.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E316340C02
0,0 0,0 false
V100135

Nut
V100136

Bolt
V100137

Screw


Install the No. 1 instrument panel brace sub-assembly with the nut, bolt and 4 screws.

Torque:
Bolt, Nut : 20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Attach the clamp.


Hide 55307C 6.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E316341C02
0,0 0,0 false
V100135

Nut
V100136

Bolt
V100137

Screw


Install the No. 2 instrument panel brace sub-assembly with the nut, bolt and 3 screws.

Torque:
Bolt, Nut : 20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 7.TIGHTEN AIR CONDITIONING UNIT ASSEMBLY

a.

Tighten the 2 screws and 3 bolts in the order shown in the illustration.

Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)

E316351C01
3.177,1.802 3.385,2 0.208,0.198 10 true (1) 2.031,1.438 2.24,1.635 0.208,0.198 10 true (2) 4.156,1.979 4.365,2.177 0.208,0.198 10 true (3) 2.615,2.271 2.823,2.469 0.208,0.198 10 true (4) 4.177,2.469 4.385,2.667 0.208,0.198 10 true (4)
V100135

Bolt
V100136

Screw



Hide 82141 8.CONNECT INSTRUMENT PANEL WIRE

a.

Install each bolt, nut and screw, and then connect the instrument panel wire.

E329522C02
2.354,4.26 2.667,4.417 0.313,0.156 10 false *A 2.385,5.969 2.698,6.125 0.313,0.156 10 false *B 4.979,6.198 5.292,6.354 0.313,0.156 10 true *C 2.969,0.677 3.177,0.844 0.208,0.167 10 true *1 3.25,1.448 3.458,1.615 0.208,0.167 10 true *1 3.938,1.438 4.146,1.604 0.208,0.167 10 true *1 3.948,0.74 4.156,0.906 0.208,0.167 10 true *1 5.781,0.438 5.99,0.604 0.208,0.167 10 true *1 6.281,0.427 6.49,0.594 0.208,0.167 10 true *1 6.542,0.729 6.75,0.896 0.208,0.167 10 true *1
*A for Manual Air Conditioning System *B for Automatic Air Conditioning System
*C w/ PTC Heater - -
*1 Ground Wire - -



b.

Connect each connector and attach each clamp.


c.

Install each bolt and each ground wire.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


d.
E316344

for Automatic Air Conditioning System:

i.

Attach the clamp.


ii.

Connect the connector.



e.
E316342

for Manual Air Conditioning System:

i.

Attach the clamp.


ii.

Connect the connector.



Hide 87212 9.INSTALL NO. 1 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324638

Install the No. 1 rear air duct with the 2 clips.


Hide 87212G 10.INSTALL NO. 3 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324637

Attach the claw to install the No. 3 rear air duct.


Hide 87213 11.INSTALL NO. 2 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324636

Attach the claw to install the No. 2 rear air duct.


Hide 87216A 12.INSTALL NO. 5 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324635

Attach the claw to install the No. 5 rear air duct.


Hide 87216B 13.INSTALL NO. 4 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324634

Attach the claw to install the No. 4 rear air duct.


Hide 55215D 14.INSTALL NO. 3 DASH PANEL INSULATOR PAD

a.
E317432

Install the No. 3 dash panel insulator pad.


Hide 55214C 15.INSTALL NO. 2 DASH PANEL INSULATOR PAD

a.
E317433

Install the No. 2 dash panel insulator pad.


Hide 55395C 16.INSTALL NO. 1 INSTRUMENT PANEL INNER BRACKET COVER LH (for LHD)

a.
E323201

Install the No. 1 instrument panel inner bracket cover LH with the 3 clips.


Hide 17.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.

for RHD:

Attach the guide to install the front floor carpet assembly to the original position as shown in the illustration.

E319752C01
1.781,0.104 2.01,0.281 0.229,0.177 10 true *A
V100155

Fastener
V113147

Install in this Direction



b.

for LHD:

Attach the guide to install the front floor carpet assembly to the original position as shown in the illustration.

E332269C02
0,0 0,0 false
V100155

Fastener
V113147

Install in this Direction



c.

Attach each fastener.


d.

for RHD:

Install the 5 clips.


e.

for LHD:

Install the 6 clips.


Hide 62414A 18.INSTALL LOWER CENTER PILLAR GARNISH LH

Hide 62413A 19.INSTALL LOWER CENTER PILLAR GARNISH RH

Hide 67918E 20.INSTALL REAR DOOR SCUFF PLATE LH

Hide 67917C 21.INSTALL REAR DOOR SCUFF PLATE RH

Hide 62112 22.INSTALL COWL SIDE TRIM BOARD LH

Hide 67914B 23.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 62111C 24.INSTALL COWL SIDE TRIM BOARD RH

Hide 67913B 25.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 26.INSTALL STEERING COLUMN ASSEMBLY

Hide 87211A 27.INSTALL NO. 2 AIR DUCT

a.
E315752

Attach the claw to install the No. 2 air duct.

NOTICE:

If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.



b.

Install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87211 28.INSTALL NO. 1 AIR DUCT

E315753

a.

Attach the claw to install the No. 1 air duct.

NOTICE:

If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.



Hide 55303B 29.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 30.INSTALL FRONT SEAT ASSEMBLY LH

Hide 31.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 87128 32.INSTALL HEATER GROMMET (for Automatic Air Conditioning System, Manual Air Conditioning System)

E315751

a.

Press the marked parts to attach the claw and install the heater grommet.

NOTICE:
·

Securely install the heater grommet in order to prevent water ingress.

·

Install the heater grommet so that there is no clearance between the grommet and heater pipe.




Hide 33.CONNECT HEATER WATER INLET HOSE (for Automatic Air Conditioning System, Manual Air Conditioning System)

a.
E336846C01
1.073,3.844 1.219,3.844 1.219,3.844 1.333,3.781 false 2.417,0.927 2.729,1.083 0.313,0.156 10 true *a 0.917,3.76 1.229,3.917 0.313,0.156 10 false *b 1.063,4.26 1.375,4.417 0.313,0.156 10 false *c 0.344,3.688 0.656,3.844 0.313,0.156 10 false *d 0.5,2.385 0.802,2.542 0.302,0.156 10 true *a
*a View A
*b Marking (Yellow)
*c Clip Installation Angle (40°)
*d 45°


Connect the heater water inlet hose with the marking facing left and attach the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the heater water inlet hose.



Hide 34.CONNECT HEATER WATER OUTLET HOSE (for Automatic Air Conditioning System, Manual Air Conditioning System)

a.
E315773C01
0.875,3.198 1.01,3.198 1.01,3.198 1.094,3.281 false 0.583,2.313 0.896,2.469 0.313,0.156 10 false *a 0.698,3.125 1.01,3.281 0.313,0.156 10 false *b 0.406,3.458 0.719,3.615 0.313,0.156 10 false *c 2.021,0.458 2.177,0.656 0.156,0.198 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (40°)


Connect the heater water outlet hose with the marking facing left and attach the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the heater water outlet hose.



Hide 88710E 35.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (for 1GD-FTV, 2GD-FTV)

a.
E315746

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the 2 O-rings to the air conditioner tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the air conditioner tube and accessory assembly.


e.

Tighten the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 88710E 36.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (except 1GD-FTV, 2GD-FTV)

a.
E315748

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.

Connect the air conditioner tube and accessory assembly.


Hide 88707 37.CONNECT SUCTION PIPE SUB-ASSEMBLY (except 1GD-FTV, 2GD-FTV)

a.
E315747

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.

Connect the suction pipe sub-assembly.


e.
E315774C01
0,0 0,0 false
V113147

Install in this Direction


Rotate the hook connector as shown in the illustration.


f.

Insert the pipe joint into the fitting hole securely and tighten the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 88710E 38.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (except 1GD-FTV, 2GD-FTV, w/ Sub-cool Accelerator)

a.
E320665

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new 2 O-rings and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.
E319141C02
0,0 0,0 false
V113147

Install in this Direction


Rotate the hook connector as shown in the illustration.


e.

Insert the pipe joint into the fitting hole securely and tighten the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 39.ADD ENGINE COOLANT (for Automatic Air Conditioning System, Manual Air Conditioning System)

Hide 40.INSPECT FOR COOLANT LEAK (for Automatic Air Conditioning System, Manual Air Conditioning System)

Hide 41. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 44. INITIALIZATION SERVO MOTOR (for Automatic Air Conditioning System)