| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0088 | Fuel Rail / System Pressure - Too High | The fuel pressure of the common rail exceeds 200000 kPa (2039 kgf/cm2, 29000 psi) (1 trip detection logic). | ·
Suction control valve (fuel supply pump assembly) ·
Pressure discharge valve (common rail assembly) ·
Open or short in suction control valve circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0088 | ·
Common Rail Pressure ·
Target Common Rail Pressure ·
Target Pump SCV Current |
For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).
When DTC P0088 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine / Data List / Common Rail Pressure.
| Engine Speed | Common Rail Pressure |
|---|---|
| Idling | Approximately 28000 to 40000 kPa |
| 3000 rpm (No engine load) | Approximately 30000 to 60000 kPa |
Check "Common Rail Pressure", "Target Common Rail Pressure" and "Target Pump SCV Current" in the freeze frame data.
| DTC Detection Drive Pattern | After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds |
The ECM stores this DTC if the fuel pressure inside the common rail is higher than 200000 kPa (2039 kgf/cm2, 29000 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.
If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| P0088 is output | A |
| P0088 and "P0190, P0192 and/or P0193" are output | B |
When there is an open circuit in the fuel pressure sensor circuit, the fuel pressure sensor outputs the maximum value. Therefore, P0088 may be stored together with DTCs which indicate common rail fuel pressure sensor circuit malfunctions.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Record the stored DTCs and freeze frame data.
| Result | Proceed to |
|---|---|
| Value of Common Rail Pressure is shifting towards 160000 kPa or higher in 3rd and 4th set of freeze frame data | B |
| Except above | A |
A
B
| *a | Component with harness connected
(ECM) |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C114-26 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| Result | Proceed to |
|---|---|
| MIL comes on or noise present in the waveform | B |
| Except above | A |
A
B
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL
Before replacing the fuel supply pump assembly, check that the wire harness between the suction control valve and ECM is not shorted to ground.
When there is a malfunction in the wire harness, Target Pump SCV Current is outside the range of 923 to 1123 mA when idling, and outside the range of 1013 to 1212 mA when the engine is running at 2500 rpm without load.
If there are no problems with the engine condition during idling, it is not necessary to perform the above wire harness inspection.
When the wire harness between the suction control valve and ECM is not shorted to ground, it can be assumed that DTC P0088 was stored due to a malfunction in the operation of the suction control valve. Therefore, it is necessary to replace the fuel supply pump assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Perform fuel supply pump initialization.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0088.
Check the DTC judgment result.
| Tester Display | Result | Proceed to |
|---|---|---|
| Pending DTC | P0088 is output | A |
| All Readiness | NORMAL | B |
| ABNORMAL | A |
If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component with harness connected
(ECM) |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C114-26 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| Result | Proceed to |
|---|---|
| MIL comes on or noise present in the waveform | A |
| Except above | B |
A
B
Replace the common rail assembly.
Click hereEngine / Hybrid System>1KD-FTV FUEL>COMMON RAIL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0088.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
| Proceed to |
|---|
| NEXT |
NEXT