Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _049378 1KD-FTV ENGINE CONTROL _0236318 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P1229  Fuel Pump System  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1229 Fuel Pump System The actual fuel pressure exceeds the target fuel pressure by 5000 kPa or higher for 30 seconds.
(1 trip detection logic)
·

Short in fuel supply pump assembly (suction control valve) circuit

·

Fuel supply pump assembly (suction control valve)

·

Fuel pressure sensor (common rail assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P1229
·

Common Rail Pressure

·

Target Common Rail Pressure

·

Injection Pressure Correction

·

Target Pump SCV Current



HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).

·

When DTC P1229 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine / Data List / Common Rail Pressure, Target Common Rail Pressure.

Under a stable condition such as idling after warm up the engine, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure when normal.

·

When there is a problem with the movement of the fuel supply pump assembly (when Common Rail Pressure is higher than Target Common Rail Pressure due to a problem in which the suction valve has difficulty closing), the values of Injection Pressure Correction and Target Pump SCV Current decrease.



CONFIRMATION DRIVING PATTERN

P1229
DTC Detection Drive Pattern Idling for 60 seconds

MONITOR DESCRIPTION

P1229 (Fuel overfeed):

The ECM stores this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When this DTC is stored, be sure to carefully examine "Common Rail Pressure", "Target Common Rail Pressure", "Target Pump SCV Current", and "Pump SCV Learning Value" in the freeze frame data.



PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
P1229 and "P0190, P0192 and/or P0193" are output B
Except above A




A

2.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)

B

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

2.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Data List / Common Rail Pressure and Target Common Rail Pressure.

Powertrain > Engine > Data List
Tester Display
Target Common Rail Pressure
Common Rail Pressure
50003 234 850,851

e.

Check that the internal fuel pressure of the common rail is within the specification below.

OK:

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure when engine is idling after warm up the engine.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
3.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C127-1 - C114-2 (PCV+) Always Below 1 Ω
C127-2 - C114-1 (PCV-) Always Below 1 Ω
C127-1 or C114-2 (PCV+) - Body ground Always 10 kΩ or higher
C127-2 or C114-1 (PCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE FUEL FILTER ELEMENT ASSEMBLY

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure, Target Common Rail Pressure.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Common Rail Pressure
50004 234 90 850,851

d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>DATA LIST / ACTIVE TEST

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749C01
3.406,2.427 3.521,2.094 3.521,2.094 3.594,2.094 false 4.417,2.656 5.021,2.479 5.021,2.479 5.083,2.479 false 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 3.708,3.292 3.938,4.208 3.938,4.208 4.073,4.208 false 0.177,1.438 1.573,1.729 1.396,0.292 10 false Active Test Operation 0.208,0.594 1.604,0.917 1.396,0.323 10 false Engine Speed (rpm) 0.552,3.281 1.458,3.521 0.906,0.24 10 false Fuel Pressure 3.646,2.01 5,2.219 1.354,0.208 10 false Target Fuel Pressure 6.469,4.135 6.875,4.406 0.406,0.271 10 false Time 2.125,2.427 2.833,2.844 0.708,0.417 10 false Less than 10000 kPa 2.99,4.271 3.677,4.51 0.688,0.24 10 false 2 seconds 5.135,2.375 6.042,2.896 0.906,0.521 10 false Abnormal Fuel Pressure 2.448,1.125 3.125,1.323 0.677,0.198 10 false Test Start 4.177,1.125 4.854,1.406 0.677,0.281 10 false Test Stop 5.625,1.135 6.302,1.333 0.677,0.198 10 false Test Start 2.125,1.823 2.896,2.25 0.771,0.427 10 false Normal Fuel Pressure 1.646,0.302 2.115,0.583 0.469,0.281 10 false 2000 1.885,0.844 2.052,1.01 0.167,0.167 10 false 0 1.75,1.313 2.083,1.552 0.333,0.24 10 false ON 1.698,1.573 2.094,1.865 0.396,0.292 10 false OFF 4.156,4.115 5.771,4.521 1.615,0.406 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Common Rail Pressure" is the actual fuel pressure.



Result:
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa. B
Except above A




A

6.REPLACE FUEL FILTER ELEMENT ASSEMBLY

B

10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL FILTER>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

9.PERFORM FUEL SUPPLY PUMP INITIALIZATION
9.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform fuel supply pump initialization.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P1229.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END