Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048930 2KD-FTV ENGINE CONTROL _0236329 ECD SYSTEM J

2KD-FTV ENGINE CONTROL  ECD SYSTEM  Lack of Power or Hesitation  


DESCRIPTION

Malfunction Condition Main Trouble Area Related Trouble Area
·

Lack of power caused by abnormal fuel injection volume (fuel supply pump malfunction, injector assembly malfunction, etc.)

·

Lack of power caused by intake air volume shortage (turbocharger malfunction, or front exhaust pipe or exhaust manifold converter blocked)


(a) Injector assembly malfunctions
·

Injector sliding malfunction

·

Injector stuck closed

·

Injector stuck open

·

Deposits in injector

·

Injector circuit malfunction


(b) Abnormal common rail pressure
·

Fuel supply pump


(c) Abnormal intake air volume
·

Intake air system leakage or clogged

·

Turbocharger

·

Front exhaust pipe blockage

·

Exhaust manifold converter blockage

·

Throttle valve does not open


·

Pressure discharge valve (P1271 stored simultaneously)

·

Intake air system blockage

·

Fuel filter element assembly

·

Throttle valve

·

Compression pressure

·

Injector compensation code

·

Fuel leak

·

Glow plug

·

Fuel pressure sensor

·

Manifold absolute pressure sensor

·

Vacuum hose connection for manifold absolute pressure sensor

·

Injector driver (P0200 stored simultaneously)

·

Vehicle modifications

·

Clutch disc wear

·

Low quality fuel

·

Frozen fuel

·

ECM



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.

·

This troubleshooting procedure checks for the cause of an obvious lack of engine power while the vehicle is being driven (such as the maximum speed being extremely low).



Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbo and intake manifold


Data List
·

MAP



Turbocharger System
Main fault
·

Air leak in the turbocharged air passage

·

Turbocharger (turbine, bearing)


Symptoms Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped)
Data List MAP
·

If there are problems with waste gate valve operation or the valve is stuck closed, the boost pressure increases. When this happens, the fuel injection amount may be reduced to protect the engine, which may result in a lack of power or hesitation.

·

With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.

·

Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.



Exhaust System
Main fault Blockage
Symptoms Lack of power (high engine speed, under heavy load)

Glow System
Main fault Open circuit, glow plug relay fault
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Measure the resistance of the glow plug

Engine - 1
Main fault Damaged, seized up
Symptoms Cannot crank, crank speed is low, strange noise

Engine - 2
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl#
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.




b.

Diesel Injection

Fuel Supply Pump
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure, Target Pump SCV Current
·

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.

·

If Target Pump SCV Current is 3000 mA or higher, the suction control valve may be stuck.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.

Fuel Filter
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure
·

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



Injector Driver
Main fault Circuit fault: The injector assembly does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as injector assembly
Diagnostic Trouble Code When the injector driver has a fault, some DTCs may be stored.

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure
·

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).


Diagnostic Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List
·

Actual Throttle Position (fully closed: 100%, fully open: 0%)

·

When the ignition switch is ON (engine stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Lack of Power


·

Engine Speed

·

MAP

·

Intake Air

·

Coolant Temp

·

Target Common Rail Pressure

·

Common Rail Pressure

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position



CAUTION / NOTICE / HINT

Explanation of Symptom


Lack of Power The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air.
The quantity of injected fuel is determined by the fuel pressure and the amount of time the injector assembly is open. Basically, the fuel pressure is controlled so that it reaches the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than atmospheric pressure.


NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).



PROCEDURE

1.READ OUTPUT DTC (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read the pending DTCs.

Result:
Result Proceed to
No DTCs are output A
Engine related DTCs are output B




A

2.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 2)

B

2.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 2)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Lack of power.


d.

With no load after the engine is warmed up, take a snapshot when idling and at 4000 rpm.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.




Result:
Proceed to
NEXT



NEXT

3.CHECK SNAPSHOT (MAP)
3.CHECK SNAPSHOT (MAP)
a.

Check MAP in the snapshot taken in procedure 2 when the engine was running at 4000 rpm with no load.

Result:
Result Proceed to
MAP is 210 kPa or higher*1 A
MAP is below 90 kPa*2 B
Except above*3 C


HINT:

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.

*1: There may be a problem in the turbocharger (waste gate valve) or fuel system.

*2: There may be a problem in the turbocharger system.

*3: There may be a problem in the intake system.




A

15.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

B

4.READ VALUE USING GTS (MAP AND ATMOSPHERIC PRESSURE)

C

14.CHECK SNAPSHOT (COMMON RAIL PRESSURE, TARGET COMMON RAIL PRESSURE AND MAP)
4.READ VALUE USING GTS (MAP AND ATMOSPHERIC PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / MAP and Atmosphere Pressure.

Powertrain > Engine > Data List
Tester Display
Atmosphere Pressure
MAP
50003 234 7,4

d.

Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).

Standard:

Difference between MAP and Atmosphere Pressure is less than 8 kPa.


HINT:
·

If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.




Result:
Result Proceed to
MAP and Atmosphere Pressure have same value A
MAP is different from actual atmospheric pressure B
Atmosphere Pressure is different from actual atmospheric pressure C



A

5.CHECK AIR INTAKE SYSTEM

B

9.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

C

12.REPLACE ECM
5.CHECK AIR INTAKE SYSTEM
a.

Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

HINT:
·

Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

·

Check for any modifications in the intake system made by the user.



OK:

No leakage or blockage.



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYST CONVERTER)

NG

10.REPAIR OR REPLACE AIR INTAKE SYSTEM
6.CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYST CONVERTER)
a.

Remove the front exhaust pipe assembly.


b.

Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.

OK:

Less than 10% of the cells are clogged.



c.

Reinstall the front exhaust pipe assembly.


Result:
Proceed to
OK
NG



OK

7.CHECK TURBOCHARGER SUB-ASSEMBLY

NG

13.REPLACE EXHAUST PIPE ASSEMBLY FRONT (CATALYST CONVERTER)
7.CHECK TURBOCHARGER SUB-ASSEMBLY

b.

Inspect the turbocharger housing.

i.

Visually check that there are no scratches or chipped areas inside the turbine housing or compressor housing.


ii.

Visually check that there are no scratches or chipped areas on the blades of the impeller or turbine wheel.



Result:
Proceed to
OK
NG



OK

8.CHECK FOR INTERMITTENT PROBLEMS

NG

11.REPLACE TURBOCHARGER SUB-ASSEMBLY
8.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.


Result:
Proceed to
NEXT



NEXT

39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE AIR INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the air intake system.


Result:
Proceed to
NEXT



NEXT

39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPLACE EXHAUST PIPE ASSEMBLY FRONT (CATALYST CONVERTER)
a.

Replace the front exhaust pipe assembly.


Result:
Proceed to
NEXT



NEXT

39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CHECK SNAPSHOT (COMMON RAIL PRESSURE, TARGET COMMON RAIL PRESSURE AND MAP)
a.

Check Common Rail Pressure, Target Common Rail Pressure and MAP in the snapshot taken in procedure 3 when the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear and the engine speed around 3000 rpm.

Result:
Result Proceed to
MAP is 230 kPa or higher at an engine speed of 3000 rpm A
Difference between Common Rail Pressure and Target Common Rail Pressure is 20000 kPa or more B
Except above C


HINT:
·

The above values are applicable under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.

·

The engine speed must be 1500 rpm or less before performing the inspection in which the accelerator pedal is fully depressed and the engine is accelerated to a speed of 3000 rpm.

·

If "Common rail pressure" follows "Target common rail pressure" during idling or low speed driving but is insufficient during acceleration or high speed driving, the fuel filter may be clogged.





A

15.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

B

17.INSPECT CLOGGED FUEL PIPE

C

26.CHECK INTAKE SYSTEM
15.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C53-2 (PIM) - C115-28 (PIM) Always Below 1 Ω
C53-3 (VC) - C114-18 (VC) Always Below 1 Ω
C53-1 (E) - C114-28 (E2) Always Below 1 Ω
C53-2 (PIM) or C115-28 (PIM) - Body ground Always 10 kΩ or higher
C53-3 (VC) or- C114-18 (VC) - Body ground Always 10 kΩ or higher
C53-1 (E) or C114-28 (E2) - Body ground Always 10 kΩ or higher



HINT:
·

Make sure that there is no evidence of any wire harnesses being crushed and that there are no wires that are about to snap.

·

Make sure that no terminals are worn down and that there are no bad connections.

·

Make sure there are no shorts between wires in areas where the wires bend or where a clamp might have slid along the wire harness.

·

Make sure there are no shorts to body ground in areas where wire harnesses are attached to metal parts.



Result:
Proceed to
OK
NG



OK

16.CHECK OR REPLACE TURBOCHARGER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK OR REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Check that the actuator rod moves and that the waste gate valve opens.

Click hereEngine / Hybrid System>2KD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER>INSPECTION

HINT:

If the waste gate valve does not open, replace the turbocharger sub-assembly.



Result:
Proceed to
NEXT



NEXT

39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.INSPECT CLOGGED FUEL PIPE
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Injection.


d.

With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.


e.

Check the Target Common Rail Pressure and Common Rail Pressure value.

A261221E24
0.177,1.708 1.167,2.167 0.99,0.458 10 false Target Common Rail Pressure 3.854,2.125 4.927,2.469 1.073,0.344 10 false Normal Common Rail Pressure 3.75,0.438 4.938,0.781 1.188,0.344 10 false Abnormal Common Rail Pressure*1 0.115,0.115 1.823,0.354 1.708,0.24 10 false Fuel Pressure During Idling 1.115,2.406 3.594,2.917 2.479,0.51 10 false Pressure varies periodically with a period of approximately 2 seconds or more 5.906,1.104 7.01,1.479 1.104,0.375 10 false Normal Condition: +/- 5000 kPa 5.906,1.448 7.042,1.958 1.135,0.51 10 false (Idling after Engine Warmed Up)

Result:
Result Proceed to
While idling the vehicle, "Common Rail Pressure" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 A
"Common Rail Pressure" is normal while idling the vehicle, but "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
Except above B


NOTICE:
·

*1: The cause may be a squashed or blocked fuel pipe or hose.

·

*2: The cause may be a clogged fuel filter.





A

18.REPAIR OR REPLACE CLOGGED FUEL LINE

B

22.REPLACE FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
18.REPAIR OR REPLACE CLOGGED FUEL LINE
a.

Repair or replace the clogged (including frozen fuel) fuel pipe.


b.

Replace the fuel filter element assembly.

HINT:

If "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element assembly.



Result:
Proceed to
NEXT



NEXT

19.BLEED AIR FROM FUEL SYSTEM
19.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

20.PERFORM FUEL SUPPLY PUMP INITIALIZATION
20.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform fuel supply pump initialization

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure, Target Common Rail Pressure.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Common Rail Pressure
50004 234 90 850,851

d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E15
3.406,2.438 3.521,2.104 3.521,2.104 3.594,2.104 false 4.417,2.656 5.021,2.479 5.021,2.479 5.083,2.479 true 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 3.708,3.271 3.938,4.188 3.938,4.188 4.073,4.188 false 0.083,1.438 1.448,1.677 1.365,0.24 10 false Active Test Operation 0.167,0.594 1.448,0.844 1.281,0.25 10 false Engine Speed (rpm) 0.542,3.271 1.448,3.51 0.906,0.24 10 false Fuel Pressure 3.646,2.021 5,2.25 1.354,0.229 10 false Target Fuel Pressure 6.469,4.135 6.865,4.313 0.396,0.177 10 false Time 2.125,2.427 2.802,2.865 0.677,0.438 10 false Less than 10000 kPa 3,4.271 3.688,4.438 0.688,0.167 10 false 2 seconds 5.125,2.385 6.031,2.885 0.906,0.5 10 false Abnormal Fuel Pressure 2.448,1.125 3.125,1.323 0.677,0.198 10 false Test Start 4.177,1.125 4.844,1.323 0.667,0.198 10 false Test Stop 5.625,1.125 6.302,1.323 0.677,0.198 10 false Test Start 2.208,1.823 2.979,2.24 0.771,0.417 10 false Normal Fuel Pressure 1.646,0.313 2.021,0.479 0.375,0.167 10 false 2000 1.885,0.854 2.052,1.021 0.167,0.167 10 false 0 1.75,1.323 2.073,1.49 0.323,0.167 10 false ON 1.698,1.583 2.021,1.75 0.323,0.167 10 false OFF 4.146,4.115 5.76,4.479 1.615,0.365 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Common Rail Pressure" is the actual fuel pressure.




Result:
Proceed to
OK
NG



OK

END

NG

23.REPLACE COMMON RAIL ASSEMBLY
22.REPLACE FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.BLEED AIR FROM FUEL SYSTEM
23.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

24.BLEED AIR FROM FUEL SYSTEM
24.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure, Target Common Rail Pressure.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Common Rail Pressure
50004 234 90 850,851

d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E21
3.406,2.438 3.521,2.104 3.521,2.104 3.594,2.104 false 4.417,2.656 5.021,2.479 5.021,2.479 5.083,2.479 true 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 3.708,3.271 3.938,4.188 3.938,4.188 4.073,4.188 false 0.083,1.427 1.448,1.667 1.365,0.24 10 false Active Test Operation 0.167,0.594 1.448,0.844 1.281,0.25 10 false Engine Speed (rpm) 0.542,3.271 1.448,3.51 0.906,0.24 10 false Fuel Pressure 3.646,2.021 5,2.25 1.354,0.229 10 false Target Fuel Pressure 6.469,4.135 6.865,4.313 0.396,0.177 10 false Time 2.125,2.427 2.792,2.813 0.667,0.385 10 false Less than 10000 kPa 3,4.271 3.688,4.438 0.688,0.167 10 false 2 seconds 5.125,2.385 6.031,2.76 0.906,0.375 10 false Abnormal Fuel Pressure 2.448,1.125 3.125,1.323 0.677,0.198 10 false Test Start 4.177,1.125 4.844,1.323 0.667,0.198 10 false Test Stop 5.625,1.125 6.302,1.323 0.677,0.198 10 false Test Start 2.208,1.823 2.969,2.219 0.76,0.396 10 false Normal Fuel Pressure 1.646,0.313 2.021,0.479 0.375,0.167 10 false 2000 1.885,0.854 2.052,1.021 0.167,0.167 10 false 0 1.75,1.323 2.073,1.49 0.323,0.167 10 false ON 1.698,1.583 2.021,1.75 0.323,0.167 10 false OFF 4.146,4.115 5.802,4.448 1.656,0.333 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Common Rail Pressure" is the actual fuel pressure.




Result:
Proceed to
NEXT



NEXT

END

26.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

HINT:
·

Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

When checking whether the intake system is clogged (which causes a low MAP), perform the following checks:

·

Check whether the air cleaner is clogged.

·

Check whether an intake hose is clogged.

·

Check whether the diesel throttle valve is stuck in the closed position.


·

Check for any modifications in the intake system made by the user.




OK:

No leaks or blockages in the intake system.


Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

NG

32.REPAIR OR REPLACE AIR INTAKE SYSTEM
27.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C53-2 (PIM) - C115-28 (PIM) Always Below 1 Ω
C53-3 (VC) - C114-18 (VC) Always Below 1 Ω
C53-1 (E) - C114-28 (E2) Always Below 1 Ω
C53-2 (PIM) or C115-28 (PIM) - Body ground Always 10 kΩ or higher
C53-3 (VC) or C114-18 (VC) - Body ground Always 10 kΩ or higher
C53-1 (E) or C114-28 (E2) - Body ground Always 10 kΩ or higher


HINT:
·

Make sure that there is no evidence of any wire harnesses being crushed and that there are no wires that are about to snap.

·

Make sure that no terminals are worn down and that there are no bad connections.

·

Make sure there are no shorts between wires in areas where the wires bend or where a clamp might have slid along the wire harness.

·

Make sure there are no shorts to body ground in areas where wire harnesses are attached to metal parts.




Result:
Proceed to
OK
NG



OK

28.CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
a.

Remove the front exhaust pipe assembly.


b.

Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.

OK:

Less than 10% of the cells are clogged.



c.

Reinstall the front exhaust pipe assembly.


Result:
Proceed to
OK
NG



OK

29.INSPECT TURBOCHARGER SUB-ASSEMBLY

NG

33.REPLACE FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
29.INSPECT TURBOCHARGER SUB-ASSEMBLY
a.

Check that the actuator rod moves and that the waste gate valve opens.

Click hereEngine / Hybrid System>2KD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER>INSPECTION


HINT:

If the waste gate valve does not open, replace the turbocharger sub-assembly.



c.

Inspect the turbocharger housing.

i.

Visually check that there are no scratches or chipped areas inside the turbine housing or compressor housing.


ii.

Visually check that there are no scratches or chipped areas on the blades of the impeller or turbine wheel.



Result:
Proceed to
OK
NG



OK

30.CHECK FOR INTERMITTENT PROBLEMS

NG

34.REPLACE TURBOCHARGER SUB-ASSEMBLY
30.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
OK
NG



OK

END

NG

35.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
32.REPAIR OR REPLACE AIR INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the air intake system.


Result:
Proceed to
NEXT



NEXT

28.CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
33.REPLACE FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
a.

Replace the front exhaust pipe assembly.


Result:
Proceed to
NEXT



NEXT

31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
34.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
35.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

36.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
36.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

37.BLEED AIR FROM FUEL SYSTEM
37.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

38.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
38.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END