32000
1.INSTALL TORQUE CONVERTER ASSEMBLY
| *a | Engine Surface |
| *b | Drive Plate Surface |
Using a vernier caliper, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly and torque converter assembly contact surface of the drive plate and ring gear sub-assembly.
| *a | Matchmark |
Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.
Install the torque converter assembly to the input shaft while keeping it horizontal.
| *1 | Front Oil Pump Oil Seal |
Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.
Do not damage the front oil pump oil seal.
Install the torque converter assembly to the input shaft while keeping it horizontal.
| *1 | Front Oil Pump Oil Seal |
Turn the torque converter assembly to engage the key of the oil pump drive gear with the slot on the torque converter assembly.
Do not push the torque converter assembly excessively when rotating it.
Do not damage the front oil pump oil seal.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.
B = A + 1.00 mm (0.0394 in.) or more
Make sure to deduct the thickness of the straightedge.
If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
36478A
2.INSTALL TRANSMISSION BREATHER BRACKET
Install the transmission breather bracket with the bolt.
Attach the clamp to connect the automatic transmission breather hose to the transfer breather bracket.
3.INSTALL WIRE HARNESS CLAMP BRACKET
| *a | Bolt A |
| *b | Bolt B |
Install 3 wire harness clamp brackets with the 3 bolts.
36100
4.INSTALL TRANSFER ASSEMBLY
5.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
| *1 | Torque Converter Centerpiece |
| *2 | Crankshaft |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1.0 g (0.0353 oz)
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
Install the automatic transmission assembly to the engine with the 5 bolts.
Do not use excessive force when installing the automatic transmission assembly.
Check that the torque converter assembly rotates.
Make sure that the wire harness or other similar items are not pinched between the contact surfaces.
Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.
82121
6.CONNECT ENGINE WIRE
Attach the 7 wire harness clamps and connect the engine wire to the automatic transmission assembly and transfer assembly with the bolt.
Connect the 5 connectors.
Push up the lever until the claw of the transmission wire connector makes a connection sound.
Attach the 5 clamps and connect the transfer breather hose sub-assembly to the automatic transmission assembly.
12371A
7.INSTALL REAR ENGINE MOUNTING INSULATOR
Install the rear engine mounting insulator to the automatic transmission assembly with the 4 bolts.
51204
8.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Connect the ends of the No. 3 frame crossmember sub-assembly to the body with the 4 bolts and 4 nuts.
Hold the bolts while tightening the nuts.
Connect the No. 3 frame crossmember sub-assembly to the rear engine mounting insulator with the 4 bolts.
9.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the installation locations of the 6 torque converter assembly setting bolts and install each bolt through the hole of the flywheel while holding the crankshaft pulley bolt with a wrench.
Install the black colored bolt first, and then the silver colored 5 bolts.
33118B
10.INSTALL STIFFENER PLATE
Install the No. 2 end plate.
Install the No. 4 cylinder block insulator.
Install the stiffener plate LH to the engine and automatic transmission assembly with the 4 bolts.
Install the stiffener plate RH (with oil cooler tube clamp) to the engine and automatic transmission assembly with the 4 bolts.
82284
11.CONNECT GROUND WIRE
Connect the ground wire to the transfer assembly with the bolt as shown in the illustration.
Make contact with the terminal stopper.
32921
12.CONNECT OIL COOLER TUBE
Install the 3 clamps to the automatic transmission assembly and engine assembly with the 4 bolts.
It is not necessary to remove the clamp unless they are being replaced.
Connect the end of the inlet oil cooler tube to the automatic transmission assembly by hand.
Connect the end of the outlet oil cooler tube to the automatic transmission assembly by hand.
Install the 3 oil cooler tube clamps with the 3 bolts.
| *a | Torque Wrench Fulcrum Length |
Using a 17 mm union nut wrench, tighten the oil cooler tube inlet and oil cooler tube outlet.
34.3 N*m (350 kgf*cm, 25 ft.*lbf)
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 300 mm (11.8 in.)): 31.2 N*m (318 kgf*cm, 23 ft.*lbf)
33823
13.INSTALL TRANSMISSION CONTROL CABLE BRACKET
Install the transmission control cable bracket with the 2 bolts.
33820B
14.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Move the shift lever to N.
Turn the transmission control shaft lever clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.
Connect the transmission control cable assembly to the transmission control cable bracket with a new clip, and then connect the cable end to the transmission control shaft lever LH with the nut.
17410
15.INSTALL FRONT EXHAUST PIPE ASSEMBLY
28100
16.INSTALL STARTER ASSEMBLY
for 2.0 kW Type:
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for 2.0 kW Type)>INSTALLATION
for BOSCH Made:
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>INSTALLATION
37100
17.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TSAM Made)>INSTALLATION
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>INSTALLATION
41110F
18.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
19.ADD TRANSFER OIL
20.ADD AUTOMATIC TRANSMISSION FLUID
21.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
22.INSPECT SHIFT LEVER POSITION
23.ADJUST AUTOMATIC TRANSMISSION FLUID
24.INSPECT FOR EXHAUST GAS LEAK
25.INSPECT FOR OIL LEAK
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
26. RESET MEMORY
If automatic transmission parts have been replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION