Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P0115  Engine Coolant Temperature Circuit  


DESCRIPTION

The engine coolant temperature sensor senses the coolant temperature. A thermistor built into the sensor changes the resistance value according to the coolant temperature. The lower the coolant temperature, the greater the thermistor resistance value, and the higher the coolant temperature, the lower the thermistor resistance value.

The engine coolant temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the engine coolant temperature sensor from the terminal THW via a resistor R. That is, the resistor R and the engine coolant temperature sensor are connected in series. When the resistance value of the engine coolant temperature sensor changes in accordance with changes in the coolant temperature, the potential at the terminal THW also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during cold engine operation.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0115 Engine Coolant Temperature Circuit Open or short in engine coolant temperature sensor circuit for 0.5 seconds or more.
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A337317E35
0.448,2.823 1.219,3.042 0.771,0.219 10 false C35 5.656,3.01 6.24,3.198 0.583,0.188 10 false C175 5.688,3.208 6.146,3.406 0.458,0.198 10 false ECM 0.438,3.021 2.969,3.24 2.531,0.219 10 false Engine Coolant Temperature Sensor 5.26,1.323 5.719,1.521 0.458,0.198 10 false THW 5.26,1.917 5.781,2.115 0.521,0.198 10 false ETHW 2.198,1.323 2.656,1.521 0.458,0.198 10 false 2 2.198,1.948 2.656,2.146 0.458,0.198 10 false 1 5.031,1.323 5.49,1.521 0.458,0.198 10 false 21 5,1.917 5.458,2.115 0.458,0.198 10 false 29 5.906,0.948 6.365,1.146 0.458,0.198 10 false 5 V 5.854,1.219 6.313,1.417 0.458,0.198 10 false R

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 61 309

d.

Read the value.

Result:
Display Proceed to
-40°C (-40°F) A
140°C (284°F) or more B
The same as actual engine coolant temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

B

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

C

2.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)
a.
A213406C34
0.74,3.5 1.167,3.76 0.427,0.26 0.26,2.771 0.573,2.969 0.313,0.198 10 false *a 0.667,0.333 0.979,0.531 0.313,0.198 10 false *1 2.531,0.313 2.844,0.51 0.313,0.198 10 false *2 2.406,1.25 2.896,1.5 0.49,0.25 10 false THW 2.417,1.698 2.969,1.958 0.552,0.26 10 false ETHW 0.833,3.542 1.365,3.719 0.531,0.177 10 false C35
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the ECT sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 61 309

f.

Read the value.

OK:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
3.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C35-2 - C175-21 (THW) Always Below 1 Ω
C35-1 - C175-29 (ETHW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.
A302633C37
2.469,1.063 2.917,1.323 0.448,0.26 10 false THW 2.479,1.51 3,1.708 0.521,0.198 10 false ETHW 0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.583,0.25 2.896,0.448 0.313,0.198 10 false *2
*1 Engine Coolant Temperature Sensor
*2 ECM


Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 61 309

e.

Read the value.

OK:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C35-2 or C175-21 (THW) - Body ground and other terminals Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR