Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P0180  Fuel Temperature Sensor "A" Circuit  


DESCRIPTION

The fuel temperature sensor senses the fuel temperature. A thermistor built into the sensor changes the resistance value according to the fuel temperature. The lower the fuel temperature, the greater the thermistor resistance value, and the higher the fuel temperature, the lower the thermistor resistance value.

The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via a resistor R. That is, resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes in accordance with changes in the fuel temperature, the potential at the terminal THF also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during low engine revolution and high fuel temperature.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0180 Fuel Temperature Sensor "A" Circuit Open or short in fuel temperature sensor circuit for 0.5 seconds or more.
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A337317E36
0.448,2.813 0.896,3.01 0.448,0.198 10 false C117 5.552,3.01 6.01,3.208 0.458,0.198 10 false C175 5.583,3.208 6.042,3.406 0.458,0.198 10 false ECM 0.438,3.021 2.969,3.24 2.531,0.219 10 false Fuel Temperature Sensor 5.26,1.333 5.719,1.531 0.458,0.198 10 false THF 5.26,1.917 5.781,2.115 0.521,0.198 10 false ETHF 2.177,1.333 2.635,1.531 0.458,0.198 10 false 2 2.177,1.927 2.635,2.125 0.458,0.198 10 false 1 5.021,1.333 5.479,1.531 0.458,0.198 10 false 23 5.031,1.927 5.49,2.125 0.458,0.198 10 false 31 5.906,0.948 6.365,1.146 0.458,0.198 10 false 5 V 5.854,1.219 6.313,1.417 0.458,0.198 10 false R

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (FUEL TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 61 403

d.

Read the value.

Result:
Display Proceed to
-40°C (-40°F) A
140°C (284°F) or more B
The same as actual engine coolant temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

B

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

C

2.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)
a.
A204471C26
0.646,3.365 1.031,3.604 0.385,0.24 0.677,3.406 1.063,3.604 0.385,0.198 10 false C117 0.677,2.698 0.99,2.896 0.313,0.198 10 false *a 2.375,1.49 2.688,1.688 0.313,0.198 10 false E2 2.365,1.031 2.823,1.229 0.458,0.198 10 false THF 0.635,0.292 0.979,0.51 0.344,0.219 11 false *1 2.646,0.26 2.958,0.458 0.313,0.198 10 false *2
*1 Fuel Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


Disconnect the fuel temperature sensor connector.


b.

Connect terminals 1 and 2 of the fuel temperaturesensor connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 61 403

f.

Read the value.

OK:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

REPLACE FUEL TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)
3.CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C117-2 - C175-23 (THF) Always Below 1 Ω
C117-1 - C175-31 (ETHF) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.
A302633C38
2.469,1.063 2.917,1.323 0.448,0.26 10 false THF 2.479,1.51 3,1.708 0.521,0.198 10 false ETHF 0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.583,0.25 2.896,0.448 0.313,0.198 10 false *2
*1 Fuel Temperature Sensor
*2 ECM


Disconnect the fuel temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 61 403

e.

Read the value.

OK:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

REPLACE INJECTION PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C117-2 or C175-23 (THF) - Body ground and other terminals Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR