While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch and to terminal STA of the ECM (STA signal).
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Refer to DTC P0617.
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>P0617
Inspect the fuses for circuits related to this system before performing the following procedure.
This procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table.
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
Confirm the vehicle specifications.
| Result | Proceed to |
|---|---|
| w/o Entry and Start System | A |
| w/ Entry and Start System | B |
A
B
Connect the GTS to DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block Assembly |
| *2 | ST NO. 1 Relay |
Remove the ST NO. 1 relay from the engine room relay block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 2 - Body ground | Engine cranking | 11 to 14 V |
The engine does not crank because the relay is not installed.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Manual Transmission Models) | B |
| NG (for Automatic Transmission Models) | C |
A
B
C
Inspect the ST NO.1 relay.
Click hereEngine / Hybrid System>2TR-FE STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for Manual Transmission Models) | A |
| OK (for Automatic Transmission Models) | B |
| NG | C |
A
B
C
Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.
Disconnect the clutch start switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 2 - B2-1 | Always | Below 1 Ω |
| ST NO. 1 relay terminal 2 - C147-17 (STA) | Always | Below 1 Ω |
| ST NO. 1 relay terminal 2, B2-1 or C147-17 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the clutch start switch assembly.
Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G135-2 (ST2) - B2-2 | Always | Below 1 Ω |
| G135-2 (ST2) - C147-15(NSW) | Always | Below 1 Ω |
| G135-2 (ST2), C147-15(NSW) or B2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>2TR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-5 (L) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| C147-17 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| C22-5 (L), C147-17 (STA) or ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the park/neutral position switch assembly.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G135-2 (ST2) - C22-4 (B) | Always | Below 1 Ω |
| G135-2 (ST2) - C147-15 (NSW) | Always | Below 1 Ω |
| G135-2 (ST2), C22-4 (B) or C147-15 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>2TR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Inspect the park/neutral position switch assembly.
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO.1 relay terminal 2 - C22-5(L) | Always | Below 1 Ω |
| ST NO.1 relay terminal 2 - C147-17 (STA) | Always | Below 1 Ω |
| ST NO. 1 relay terminal 2, C22-5 (L) or C147-17 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-16 (STAR) - C22-4 (B) | Always | Below 1 Ω |
| G17-16 (STAR) - C147-15 (NSW) | Always | Below 1 Ω |
| G17-16 (STAR) or C22-4 (B) or C147-15 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG