Home › Engine / Hybrid System › 1GR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD › from 2016.01
RM3270E _51 Engine / Hybrid System _048950 1GR-FE INTAKE / EXHAUST _0241382 EXHAUST MANIFOLD A

1GR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

Hide 17105 2.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A346120C01
2.75,1 2.917,1 2.917,1 3.104,1.24 false 2.583,0.917 2.896,1.115 0.313,0.198 10 false *a
*a Oval Shape
V100135

Forward


Install a new gasket to the cylinder head LH with the oval shape facing rearward.

NOTICE:

Make sure the gasket is installed facing the proper direction.



b.

Install the exhaust manifold sub-assembly LH with 6 new nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Connect the air fuel ratio sensor connector.


Hide 17119 3.INSTALL NO. 2 MANIFOLD STAY

a.

Install the No. 2 manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 89467B 4.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 17104 5.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A346121C01
2.167,1.396 2.5,1 2.5,1 2.667,1 true 2.667,0.917 2.917,1.083 0.25,0.167 10 true *a
*a Oval Shape
V100135

Forward


Install a new gasket to the cylinder head sub-assembly RH with the oval shape facing forward.

NOTICE:

Make sure the gasket is installed facing the proper direction.



b.

Install the exhaust manifold sub-assembly RH with 6 new nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Connect the air fuel ratio sensor connector.


Hide 17118 6.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17410 7.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install the front exhaust pipe assembly to the No. 1 exhaust pipe support.


b.

Using a wire brush, remove any foreign matter from the gasket installation surface.


c.

Install a new gasket to the end of the front exhaust pipe assembly that connects to the exhaust manifold sub-assembly RH.

NOTICE:

Do not reuse the gasket.



d.

Connect the front exhaust pipe assembly to the exhaust manifold sub-assembly RH with the 2 new nuts.

Torque:
54.3 N*m (554 kgf*cm, 40 ft.*lbf)


e.
A111834

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

40 mm (1.57 in.)


If the free length is less than the minimum, replace the compression spring.


f.
A076194C38
2.031,1.583 1.594,1.885 1.594,1.885 1.479,1.885 true 2.438,0.979 3.042,0.979 true 1.271,1.781 1.49,1.958 0.219,0.177 10 false *1 3.104,0.875 3.323,1.052 0.219,0.177 10 false *a
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap on a new gasket until its surface is flush with the front exhaust pipe assembly.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the tail exhaust pipe assembly, do not push in the gasket with the tail exhaust pipe assembly.




g.

Connect the front exhaust pipe assembly to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


h.
A374940

Connect the heated oxygen sensor connector.


i.

Attach the 2 clamps.


Hide 17450B 8.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 10.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

Hide 53882F 11.INSTALL FRONT FENDER SEAL RH

Hide 53882F 12.INSTALL FRONT FENDER SEAL LH

Hide 53736 13.INSTALL FRONT UPPER FENDER APRON SEAL RH

Hide 53737B 14.INSTALL FRONT UPPER FENDER APRON SEAL LH