Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.01
RM3270E _51 Engine / Hybrid System _048947 1GR-FE ENGINE MECHANICAL _0243428 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 2.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Attach the engine sling device and hang the engine assembly with the chain block.


b.

Remove the engine assembly from the engine stand.


Hide 3.INSTALL ENGINE ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Slowly lower the engine assembly into the engine compartment.


b.

Install the engine assembly to the body with the 4 bolts and 4 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
A358252C01
0.26,1.167 0.26,0.969 0.26,0.969 0.688,0.729 true 1.552,1.25 1.76,1.448 0.208,0.198 10 false *a 0.188,1.208 0.365,1.375 0.177,0.167 10 false *b
*a Front Engine Mounting Insulator
(LH Side)
*b Claw (Stopper)
V100135

Front


·

Make sure to tighten the side with the nut.

·

When installing a bolt with a claw (stopper), make sure to install the bolt with the claw (stopper) as shown in the illustration so that a clearance is maintained between the claw (stopper) and the intermediate shaft.




c.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.


Hide 32101 4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 6.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 41110F 10.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

Hide 11.INSTALL POWER STEERING LINK ASSEMBLY (for 4WD)

Hide 45219 12.CONNECT STEERING SLIDING YOKE (for 4WD)

Hide 43410D 13.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING (for 4WD)

Hide 43420 14.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)

Hide 43410 15.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:

Use the same procedure described for the LH side.


Hide 48069 16.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for 4WD)

Hide 48068 17.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for 4WD)

HINT:

Use the same procedure described for the LH side.


Hide 18.CONNECT TIE ROD END SUB-ASSEMBLY LH (for 4WD)

Hide 19.CONNECT TIE ROD END SUB-ASSEMBLY RH (for 4WD)

HINT:

Use the same procedure described for the LH side.


Hide 89543 20.CONNECT FRONT SPEED SENSOR LH (for 4WD)

Hide 89542 21.CONNECT FRONT SPEED SENSOR RH (for 4WD)

HINT:

Use the same procedure described for the LH side.


Hide 43502H 22.INSTALL FRONT AXLE SHAFT NUT (for 4WD)

Hide 43514C 23.INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)

Hide 37140 24.INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

Hide 23802B 26.CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

a.

Connect the No. 2 fuel pipe sub-assembly, and slide the clamp to secure the hose.


Hide 23801P 27.CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 28.INSTALL WATER HOSE SUB-ASSEMBLY

a.
A375348

Install the water hose sub-assembly, and slide the 4 clamps to secure the hose.


Hide 88320 29.CONNECT COOLER COMPRESSOR ASSEMBLY

Hide 82121 31.CONNECT ENGINE WIRE (for LHD)

a.
A349979

Connect the 2 connectors to the engine room relay block.


b.

Connect the engine wire to the engine room relay block with the nut.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.
A349978

Attach the 2 claws and install the No. 1 relay block cover side to the engine room relay block.


d.
A349977

Attach the 3 claws and install the No. 1 relay block cover upper to the engine room relay block.


e.
A349976

Attach the 2 clamps and connect the No. 2 engine wire with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


f.

Install the battery tray.


g.

Install the battery.


h.
A349975

Install the battery hold down clamp with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


i.
A349974

Tighten the nut and install the positive (+) battery terminal.

Torque:
5.35 N*m (55 kgf*cm, 47 in.*lbf)

HINT:
A349980N01
1.563,0.021 1.708,0.177 0.146,0.156 10 true 8° 1.75,0.021 1.896,0.177 0.146,0.156 10 true 8°

Position the positive (+) battery terminal as shown in the illustration.



j.
A349973

Connect the engine room main wire to the battery positive cable with the nut.

Torque:
7.55 N*m (77 kgf*cm, 67 in.*lbf)


k.
A375349N01
0.448,0.271 0.906,0.469 0.458,0.198 10 false 45° 0.906,0.271 1.365,0.469 0.458,0.198 10 false 45°

Push the engine wire through the dash panel into the cabin.

HINT:

The wire should be within the range shown in the illustration.



l.

Connect the engine wire and attach the clamp to the bracket.


m.
A375346

Connect the engine wire with the bolt.

Torque:
7.55 N*m (77 kgf*cm, 67 in.*lbf)


n.
A375345

Connect the connector.


o.
A375344

Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.


Hide 82121 32.CONNECT ENGINE WIRE (for RHD)

a.
A349979

Connect the 2 connectors to the engine room relay block.


b.

Connect the engine wire to the engine room relay block with the nut.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.
A349978

Attach the 2 claws and install the No. 1 relay block cover side to the engine room relay block.


d.
A349977

Attach the 3 claws and install the No. 1 relay block cover upper to the engine room relay block.


e.
A349976

Attach the 2 clamps and connect the No. 2 engine wire with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


f.

Install the battery tray.


g.

Install the battery.


h.
A349975

Install the battery hold down clamp with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


i.
A349974

Tighten the nut and install the positive (+) battery terminal.

Torque:
5.35 N*m (55 kgf*cm, 47 in.*lbf)

HINT:
A349980N01
1.563,0.021 1.708,0.177 0.146,0.156 10 true 8° 1.75,0.021 1.896,0.177 0.146,0.156 10 true 8°

Position the positive (+) battery terminal as shown in the illustration.



j.
A349973

Connect the engine room main wire to the battery positive cable with the nut.

Torque:
7.55 N*m (77 kgf*cm, 67 in.*lbf)


k.
A349972N01
2.26,0.24 2.573,0.448 0.313,0.208 10 false 45° 2.781,0.25 3.094,0.458 0.313,0.208 10 false 45°

Push the engine wire through the dash panel into the cabin.

HINT:

The wire should be within the range shown in the illustration.



l.

Connect the engine wire and attach the clamp to the bracket.


m.
A346254

Connect the engine wire with the bolt.

Torque:
7.55 N*m (77 kgf*cm, 67 in.*lbf)


n.
A346253

Connect the connector.


o.
A340245

Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.


Hide 55550 34.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55607 35.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 11363A 36.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 28100 37.INSTALL STARTER ASSEMBLY

Hide 17105 38.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17104 40.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17410 42.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17450B 43.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 17129 44.INSTALL INTAKE AIR SURGE TANK

Hide 44320 45.CONNECT VANE PUMP ASSEMBLY

a.

Connect the vane pump assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Do not hit other parts with the pulley when installing the vane pump.



b.

Connect the connector.


Hide 16400 46.INSTALL RADIATOR ASSEMBLY

Hide 32941 47.CONNECT NO. 1 OIL COOLER INLET HOSE

Hide 32942 48.CONNECT NO. 1 OIL COOLER OUTLET HOSE

Hide 16711 49.INSTALL FAN SHROUD

Hide 16470 50.INSTALL RADIATOR RESERVOIR

Hide 16571 51.INSTALL RADIATOR HOSE INLET

Hide 16572 52.INSTALL RADIATOR HOSE OUTLET

Hide 16593 53.INSTALL NO. 1 RADIATOR AIR GUIDE

Hide 17700 54.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Connect the 3 clamps to the air cleaner case sub-assembly.


Hide 17801 55.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 56.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

Hide 53294C 57.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 58.INSTALL RADIATOR SIDE DEFLECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 53735B 59.INSTALL FRONT UPPER FENDER APRON SEAL LH

a.

Install the front upper fender apron seal LH with 6 new clips.


Hide 53735B 60.INSTALL FRONT UPPER FENDER APRON SEAL RH

a.

Install the front upper fender apron seal RH with 6 new clips.


Hide 53882F 61.INSTALL FRONT FENDER SEAL LH

a.

Install the front fender seal LH with 6 new clips.


Hide 53882F 62.INSTALL FRONT FENDER SEAL RH

a.

Install the front fender seal RH with 6 new clips.


Hide 63.ADD DIFFERENTIAL OIL (for 4WD)

Hide 51407A 64.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51442 65.INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51410 66.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Torque:
for M6 bolt : 11.5 N*m (117 kgf*cm, 8 ft.*lbf)
for M8 bolt : 28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 53301 67.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the washer nozzle hose.


c.

Adjust the hood sub-assembly.

Click hereVehicle Exterior>DOOR / HATCH>HOOD>ADJUSTMENT


Hide 68.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION