Home › Drivetrain › RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › from 2016.01
RM3270E _52 Drivetrain _048961 RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE _0242084 MANUAL TRANSMISSION ASSEMBLY A

RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C03
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58810J 3.REMOVE CONSOLE BOX ASSEMBLY

Hide 58280A 4.REMOVE SHIFT LEVER BOOT ASSEMBLY

a.
C324629

Remove the 6 screws, 4 clips and shift lever boot assembly.


Hide 33530F 5.REMOVE SHIFT LEVER ASSEMBLY

a.
C332406

Detach the shift lever cap boot from the manual transmission.


b.

Cover the shift lever cap with a cloth.


c.
C353574C01
1.865,0.99 2,1.24 2,1.24 2.458,1.24 true 2.521,1.156 2.833,1.354 0.313,0.198 10 false *1
*1 Shift Lever Cap
V113147

Push
V113148

Counterclockwise
V113149

Pull out


Pull out the shift lever assembly to remove it as shown in the illustration.


Hide 33548F 6.REMOVE NO. 1 FLOOR SHIFT BUSH

a.
C329824

Remove the No. 1 floor shift bush from the shift lever assembly.


Hide 51410 8.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

Hide 17410 10.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 1GD-FTV)

Hide 17410 11.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2GD-FTV)

Hide 17410 12.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2KD-FTV)

Hide 13.REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY

Hide 28100 14.REMOVE STARTER ASSEMBLY (for 1GD-FTV)

Hide 28100 16.REMOVE STARTER ASSEMBLY (for 2KD-FTV)

Hide 12584 17.REMOVE NO. 4 CYLINDER BLOCK INSULATOR

a.

Remove the No. 4 cylinder block insulator.


Hide 33119 18.REMOVE STIFFENER PLATE LH

a.
C324648

Remove the 4 bolts and stiffener plate LH.


Hide 33118 19.REMOVE STIFFENER PLATE RH

a.
C325402

Remove the 4 bolts and stiffener plate RH.


Hide 21.DISCONNECT GROUND CABLE

a.
C335925

Remove the bolt and disconnect the ground cable.


Hide 22.SUPPORT MANUAL TRANSMISSION ASSEMBLY

a.
C324639

Support the manual transmission with a transmission jack.

NOTICE:
·

Make sure the high transmission jack attachment is centered on the safety stand.

·

Secure the part with a rope, attachment, etc.




Hide 51204 23.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C351866

Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.


b.
C325680

Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.


Hide 12371A 24.REMOVE REAR ENGINE MOUNTING INSULATOR

a.
C324650

Remove the 4 bolts and rear engine mounting insulator from the manual transmission assembly.


Hide 25.DISCONNECT WIRE HARNESS

a.
C328310

w/ Intelligent Manual Transmission Switch:

i.

Detach the 5 wire harness clamps.


ii.

Remove the bolt.


iii.

Disconnect the connector and wire harness.



b.
C328311

w/o Intelligent Manual Transmission Switch:

i.

Detach the 3 wire harness clamps.


ii.

Remove the bolt.


iii.

Disconnect the connector and wire harness.



Hide 26.REMOVE MANUAL TRANSMISSION ASSEMBLY

a.
C324649

Remove the 5 bolts and manual transmission assembly.

NOTICE:

As the manual transmission assembly is very heavy, be sure to support it securely.



Hide 33019C 27.REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY

a.
C324642

Detach the 4 breather hose clamps and bracket.


b.

Remove the transmission breather sub-assembly from the control shift lever retainer sub-assembly.


c.
C324645

Remove the 3 bolts and 3 brackets.


Hide 28.REMOVE WIRING HARNESS CLAMP BRACKET

a.
C324644

w/ Intelligent Manual Transmission Switch:

i.

Remove the 6 bolts and 5 wiring harness clamp brackets.



b.
C328314

w/o Intelligent Manual Transmission Switch:

i.

Remove the 5 bolts and 4 wiring harness clamp brackets.



Hide 33146 29.REMOVE EXTENSION HOUSING DUST DEFLECTOR

a.
C324652C01
1.167,0.188 1.469,0.583 true 0.99,0.063 1.302,0.219 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, pry out the extension housing dust deflector.

NOTICE:

Be careful not to damage the extension housing sub-assembly.


HINT:

Tape the screwdriver tip before use.