When the back door closer does not operate, one of the following may be the cause: 1) improper fit of the back door, or a foreign object is stuck in the back door, 2) a malfunction in the multiplex network door ECU power source circuit, 3) a malfunction in the back door lock assembly circuit, or 4) a malfunction in the multiplex network door ECU.
Inspect fuses for circuits related to this system before performing the following inspection procedure.
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system*.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
*: w/ Power Back Door System
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC B2250 is output | B |
| DTC B2251 is output | C |
A
B
C
Turn the power back door main switch so that it is not pushed.
Check if the back door can be fully closed by hand.
| Result | Proceed to |
|---|---|
| The back door can be closed normally | A |
| The back door cannot be closed normally | B |
A
B
w/ Power Back Door System:
| *a | Rear view of wire harness connector
(to Multiplex Network Door ECU) |
Disconnect the multiplex network door ECU connectors.
Disconnect the multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V13-7 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V12-1 (ECUB) - Body ground | Always | 11 to 14 V |
| V13-8 (B) - Body ground | Always | 11 to 14 V |
| V12-7 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V |
w/o Power Back Door System:
| *a | Rear view of wire harness connector
(to Multiplex Network Door ECU) |
Disconnect the multiplex network door ECU connectors.
Disconnect the multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V26-7 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V25-1 (ECUB) - Body ground | Always | 11 to 14 V |
| V26-8 (B) - Body ground | Always | 11 to 14 V |
| V25-7 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back door lock assembly.
Inspect the back door lock assembly.
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ Power Back Door System:
Disconnect the V23 and V24 back door lock assembly connectors.
Disconnect the V12 and V13 multiplex network door ECU connectors.
Disconnect the G9 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V24-2 (M+) - V13-10 (DC+) | Always | Below 1 Ω |
| V24-1 (M-) - V13-9 (DC-) | Always | Below 1 Ω |
| V23-4 (CTY) - V12-20 (FUL) | Always | Below 1 Ω |
| V23-2 (FSW) - V12-6 (PAWL) | Always | Below 1 Ω |
| V23-3 (CLS) - V12-24 (HAF) | Always | Below 1 Ω |
| V23-6 (OPN) - V12-21 (POS) | Always | Below 1 Ω |
| V23-1 (E) - Body ground | Always | Below 1 Ω |
| V23-2 (M+) or V13-10 (DC+) - Body ground | Always | 10 kΩ or higher |
| V23-1 (M-) or V13-9 (DC-) - Body ground | Always | 10 kΩ or higher |
| V23-2 (FSW) or V12-6 (PAWL) - Body ground | Always | 10 kΩ or higher |
| V23-4 (CTY) or V12-20 (FUL) - Body ground | Always | 10 kΩ or higher |
| V23-3 (CLS) or V12-24 (HAF) - Body ground | Always | 10 kΩ or higher |
| V23-6 (OPN) or V12-21 (POS) - Body ground | Always | 10 kΩ or higher |
w/o Power Back Door System:
Disconnect the V23 and V24 back door lock assembly connectors.
Disconnect the V25 and V26 multiplex network door ECU connectors.
Disconnect the G9 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V24-2 (M+) - V13-10 (DC+) | Always | Below 1 Ω |
| V24-1 (M-) - V13-9 (DC-) | Always | Below 1 Ω |
| V23-4 (CTY) - V12-20 (FUL) | Always | Below 1 Ω |
| V23-2 (FSW) - V12-6 (PAWL) | Always | Below 1 Ω |
| V23-3 (CLS) - V12-24 (HAF) | Always | Below 1 Ω |
| V23-6 (OPN) - V12-21 (POS) | Always | Below 1 Ω |
| V23-1 (E) - Body ground | Always | Below 1 Ω |
| V23-2 (M+) or V13-10 (DC+) - Body ground | Always | 10 kΩ or higher |
| V23-1 (M-) or V13-9 (DC-) - Body ground | Always | 10 kΩ or higher |
| V23-2 (FSW) or V12-6 (PAWL) - Body ground | Always | 10 kΩ or higher |
| V23-4 (CTY) or V12-20 (FUL) - Body ground | Always | 10 kΩ or higher |
| V23-3 (CLS) or V12-24 (HAF) - Body ground | Always | 10 kΩ or higher |
| V23-6 (OPN) or V12-21 (POS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG