Home › Engine / Hybrid System › 2GD-FTV ENGINE MECHANICAL › CYLINDER HEAD GASKET › from 2016.01
RM3270E _51 Engine / Hybrid System _048923 2GD-FTV ENGINE MECHANICAL _0242426 CYLINDER HEAD GASKET A

2GD-FTV ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of ECM
·

Learning values save

·

Learning values write


Engine starting (Click here)
Code registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.
Replacement of engine assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)
Clear Crank Time Compensation Data Engine starting (Click here)
Replacement of crankshaft position sensor plate Clear Crank Time Compensation Data Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data (Click here)
Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)
·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly

·

Replacement of turbocharger sub-assembly

·

Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor


Perform initialization - (Click here)
for Automatic Transmission:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


·

for AC60E:

(Click here)

·

for AC60F:

(Click here)


for Automatic Transmission:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
for 4WD:

Front wheel alignment adjustment


·

Clearing zero point calibration data

·

Yaw rate and acceleration sensor zero point calibration


VSC malfunctioning (Click here)

CAUTION:
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 11310 2.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 13801 3.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 4.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 5.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A344477N01
3.073,1.823 3.208,2 0.135,0.177 10 false 1 0.406,0.229 0.542,0.406 0.135,0.177 10 false 2 1.073,0.208 1.208,0.385 0.135,0.177 10 false 8 1.708,0.208 1.927,0.375 0.219,0.167 10 false 10 2.417,0.208 2.552,0.385 0.135,0.177 10 false 5 3.083,0.229 3.219,0.406 0.135,0.177 10 false 3 2.406,1.844 2.542,2.021 0.135,0.177 10 false 7 1.74,1.844 1.875,2.021 0.135,0.177 10 false 9 1.063,1.844 1.198,2.021 0.135,0.177 10 false 6 0.396,1.833 0.531,2.01 0.135,0.177 10 true 4

Uniformly loosen the 10 cylinder head set bolts in several passes in the sequence shown in the illustration. Then remove the 10 cylinder head set bolts and 6 cylinder head set bolt spacers.

NOTICE:
·

Cylinder head sub-assembly warpage or cracking could result from removing bolts in the incorrect order.

·

Be careful not to drop the cylinder head set bolt spacers into the cylinder head sub-assembly.




b.

Lift the cylinder head sub-assembly from the ring pins on the cylinder block sub-assembly, and place the cylinder head sub-assembly on wooden blocks on a bench.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.


HINT:

If the cylinder head sub-assembly is difficult to lift, use a screwdriver to pry between the cylinder head sub-assembly and cylinder block sub-assembly.



Hide 11115 6.REMOVE CYLINDER HEAD GASKET

Hide 11101A 7.INSPECT CYLINDER HEAD SET BOLT