Home › Engine / Hybrid System › 2GD-FTV ENGINE MECHANICAL › ENGINE UNIT › from 2016.01
RM3270E _51 Engine / Hybrid System _048923 2GD-FTV ENGINE MECHANICAL _0242430 ENGINE UNIT A

2GD-FTV ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12281A 1.REMOVE NO. 1 ENGINE HANGER

a.
A343515

Remove the 2 bolts and No. 1 engine hanger from the cylinder head sub-assembly.


Hide 12582 2.REMOVE NO. 2 CYLINDER BLOCK INSULATOR

a.
A343516

Remove the No. 2 cylinder block insulator from the front No. 1 engine mounting bracket LH.


Hide 12315 3.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.
A343517

Remove the 4 bolts and front No. 1 engine mounting bracket LH from the cylinder block sub-assembly.


Hide 12583A 4.REMOVE NO. 3 CYLINDER BLOCK INSULATOR

a.
A343518

Remove the No. 3 cylinder block insulator from the cylinder block sub-assembly.


Hide 12501 5.REMOVE GENERATOR BRACKET SUB-ASSEMBLY

a.
A343519

Remove the 4 bolts and generator bracket sub-assembly from the cylinder head sub-assembly and timing chain case assembly.


Hide 12311 6.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.
A343520

Remove the 4 bolts and front No. 1 engine mounting bracket RH from the cylinder block sub-assembly.


Hide 15071 7.REMOVE ENGINE OIL COOLER SET

Hide 15601 8.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 15600A 9.REMOVE OIL FILTER UNION

a.
A343521

Using a 27 mm deep socket wrench, remove the oil filter union from the oil filter bracket.


Hide 15677 10.REMOVE OIL FILTER BRACKET

a.
A343522

Remove the bolt, 2 nuts and oil filter bracket from the cylinder block sub-assembly.


b.

Remove the 2 O-rings from the cylinder block sub-assembly.


Hide 23670 11.REMOVE INJECTOR ASSEMBLY

Hide 23682 12.REMOVE NOZZLE HOLDER GASKET

Hide 11401Q 13.REMOVE CAMSHAFT POSITION SENSOR

Hide 12108 14.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


Hide 12108A 15.REMOVE OIL FILLER CAP GASKET

a.

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 11201 16.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12585 17.REMOVE NO. 5 CYLINDER BLOCK INSULATOR

a.
A343523

Remove the No. 5 cylinder block insulator from the cylinder block sub-assembly.


Hide 12581A 18.REMOVE NO. 1 CYLINDER BLOCK INSULATOR

a.
A343524

Remove the No. 1 cylinder block insulator from the cylinder block sub-assembly.


Hide 19.REMOVE CRANKSHAFT POSITION SENSOR HARNESS BRACKET

a.
A343525

Disconnect the crankshaft position sensor connector.


b.

Remove the bolt and crankshaft position sensor harness bracket from the cylinder block sub-assembly.


Hide 11401G 20.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12144 21.REMOVE OIL PAN COVER SILENCER

Hide 89491 22.REMOVE ENGINE OIL LEVEL SENSOR

Hide 12101 23.REMOVE OIL PAN SUB-ASSEMBLY

Hide 15104 24.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A343526

Remove the 4 bolts, oil strainer sub-assembly and gasket from the cylinder block sub-assembly.


Hide 11381 25.REMOVE REAR ENGINE OIL SEAL RETAINER

a.
A343527

Remove the 5 bolts.


b.
A343528

Remove the rear engine oil seal retainer by prying between the rear engine oil seal retainer and cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 11381A 26.REMOVE REAR ENGINE OIL SEAL

a.
A343529C01
2.156,1.385 2.833,1.385 true 0.5,1.615 1.177,1.615 true 2.885,1.292 3.198,1.448 0.313,0.156 10 false *a 0.323,1.51 0.635,1.667 0.313,0.156 10 false *a
*a Wooden Block


Place the rear engine oil seal retainer on wooden blocks.


b.

Using a screwdriver, tap out the rear engine oil seal from the rear engine oil seal retainer.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.



Hide 16100 27.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 28.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley and crankshaft pulley set bolt to the crankshaft.


b.
A347371C01
0.802,1.365 1.49,1.365 true 1.594,1.365 1.594,2.031 true 2.219,3.313 2.219,3.979 true 1.01,3.313 1.01,3.979 true 0.625,1.26 0.802,1.469 0.177,0.208 10 true *a 2.135,3.979 2.333,4.167 0.198,0.188 10 true *a 1.521,2.031 1.74,2.208 0.219,0.177 10 true *a 0.927,3.969 1.125,4.156 0.198,0.188 10 true *a
*a Timing Mark


Align the timing mark of the crankshaft pulley and timing chain cover sub-assembly by rotating the crankshaft clockwise.


c.

Make sure that the timing mark of the camshaft timing sprocket is at the top.

HINT:

If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).



Hide 11324 29.REMOVE TIMING CHAIN COVER PLATE

Hide 22100 30.REMOVE SUPPLY PUMP ASSEMBLY

NOTICE:
A347307

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.


a.
A343530C01
0.688,3.979 0.688,3.385 true 1.406,3.792 2.031,3.792 true 1.333,4.406 1.573,4.615 0.24,0.208 10 false *a 0.552,4 1.01,4.198 0.458,0.198 10 false SST 2.083,3.708 2.542,3.906 0.458,0.198 10 false SST
*a Hold
V100135

Turn


Using SST, hold the crankshaft pulley and loosen the supply pump shaft nut.

SST
09213-58014  (91551-80840)
09330-00021  

NOTICE:

Do not excessively loosen the supply pump shaft nut, otherwise SST cannot be installed.


HINT:

Rotate the supply pump shaft nut once to loosen it.



b.
A344938N01
1.219,0.198 1.406,0.198 1.406,0.198 1.885,0.719 true 0.917,0.104 1.229,0.333 0.313,0.229 10 true SST

Install SST to the timing chain cover sub-assembly with the 3 bolts.

SST
09241-11010  

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A347063C02
1.865,3.135 2.458,2.563 2.458,2.563 2.656,2.563 true 0.333,0.156 0.646,0.313 0.313,0.156 10 false *a 0.344,2.5 0.656,2.656 0.313,0.156 10 false *b 2.698,2.469 3.01,2.625 0.313,0.156 10 false *c
*a Engine Front Side
*b Engine Rear Side
*c Hexagonal Portion


·

Make sure that the installation direction of SST is as shown in the illustration.

·

Align the hexagonal portion of SST with the supply pump shaft nut to install SST.




c.
A343531

Loosen the 3 nuts to the ends of the stud bolts.

NOTICE:

Do not completely remove the nuts. Otherwise, the supply pump assembly may fall off.



d.
A343532N01
2.177,1.469 2.76,1.885 2.76,1.885 2.948,1.885 true 3,1.802 3.385,2 0.385,0.198 10 false SST

Using SST, loosen the supply pump shaft nut and detach the supply pump assembly and injection pump drive gear.


e.

Remove the 3 nuts from the stud bolts.


f.

Remove the O-ring from the supply pump assembly.


g.

Remove SST from the timing chain cover sub-assembly.


h.
A343534

Remove the supply pump shaft nut from the timing chain cover sub-assembly service hole.


i.

Remove the crankshaft pulley set bolt and crankshaft pulley from the crankshaft.


Hide 22815A 31.REMOVE INJECTION PUMP INSULATOR

a.
A343533

Remove the injection pump insulator from the cylinder block sub-assembly.


Hide 11302 32.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11303A 33.REMOVE FRONT CRANKSHAFT OIL SEAL

Hide 15133B 34.REMOVE OIL PUMP RELIEF VALVE PLUG

a.
A343535

Remove the oil pump relief valve plug and gasket from the timing chain cover sub-assembly.


Hide 35.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR

Hide 13519 36.REMOVE OIL PUMP DRIVE GEAR

Hide 13566B 37.REMOVE TIMING CHAIN GUIDE

Hide 13550 38.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A343536C01
1.823,0.25 2.031,0.25 2.031,0.25 2.031,0.969 true 1.792,2.01 2,2.01 2,2.01 2,1.521 true 1.615,1.906 1.813,2.094 0.198,0.188 10 true *a 1.646,0.146 1.823,0.333 0.177,0.188 10 true *b
*a Stopper Plate
*b Plunger


Allow the plunger to extend slightly, and then rotate the stopper plate clockwise to release the lock. Once the lock is released, push the plunger into the No. 2 chain tensioner assembly.


b.
A343537C01
1.302,1.979 2.052,1.979 true 1.125,1.875 1.333,2.063 0.208,0.188 10 true *a
*a Pin


Move the stopper plate counterclockwise to set the lock, and then insert a pin into the stopper plate hole.


c.
A343538

Remove the 2 bolts and No. 2 chain tensioner assembly from the timing chain case assembly.


Hide 39.REMOVE NO. 2 CHAIN TENSIONER SLIPPER

a.
A343539

Remove the bolt and No. 2 chain tensioner slipper from the timing chain case assembly.


Hide 13562 40.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A343540

Remove the 2 bolts and No. 2 chain vibration damper from the timing chain case assembly.


Hide 13507 41.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

a.

Remove the No. 2 chain sub-assembly from the camshaft timing sprockets and injection pump drive gear.


Hide 13540 42.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
A347238C01
0.635,1.25 0.635,0.656 true 1.615,1.719 1.615,1.125 true 2.49,1.656 2.708,1.271 2.708,1.271 2.875,1.271 true 0.563,1.26 0.875,1.417 0.313,0.156 10 false *a 1.552,1.75 1.865,1.906 0.313,0.156 10 false *b 2.927,1.188 3.24,1.344 0.313,0.156 10 false *c
*a No. 1 Chain Tensioner Assembly Body
*b Spring
*c Plunger


·

When the pin is removed from the No. 1 chain tensioner assembly, the plunger and spring may come off of the No. 1 chain tensioner assembly body, but this is not a malfunction.

·

Before installing the plunger and spring to the No. 1 chain tensioner assembly body, check that they are free of foreign matter and not damaged.



a.
A343541C01
0.448,2.729 1.135,2.729 true 1.906,2.115 1.906,2.76 true 2.531,0.958 2.771,0.354 2.771,0.354 2.927,0.354 true 2.521,1.01 2.521,1.375 2.521,1.375 2.698,1.375 true 0.281,2.635 0.479,2.813 0.198,0.177 10 true *a 1.844,2.781 2.052,2.969 0.208,0.188 10 true *b 2.958,0.271 3.198,0.427 0.24,0.156 10 false *c 2.74,1.271 2.938,1.448 0.198,0.177 10 true *a
*a Pin
*b Plunger
*c Plunger Groove


Fully insert the plunger, align the No. 1 chain tensioner assembly body hole with the plunger groove and insert the pin as shown in the illustration.


b.
A343542

Remove the 2 bolts, No. 1 chain tensioner assembly and gasket from the cylinder block sub-assembly.


Hide 13559 43.REMOVE NO. 1 CHAIN TENSIONER SLIPPER

a.
A343543

Remove the No. 1 chain tensioner slipper from the straight pin.


Hide 13561 44.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A343544

Remove the bolt and No. 1 chain vibration damper from the cylinder block sub-assembly.


Hide 13506 45.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

a.
A343545

Remove the crankshaft timing sprocket, injection pump drive gear with No. 1 chain sub-assembly from the crankshaft and supply pump shaft.


Hide 13523 46.REMOVE CAMSHAFT TIMING SPROCKET

a.

for Exhaust Side:

i.
A343546C01
2.833,0.021 3.146,0.177 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Hold the hexagonal portion of the No. 2 camshaft with a wrench and remove the camshaft timing sprocket bolt and camshaft timing sprocket from the No. 2 camshaft.

NOTICE:

Be careful not to damage the No. 2 camshaft or cylinder head sub-assembly with the wrench.




b.

for Intake Side:

i.
A343547C01
2.396,0.021 2.708,0.177 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Hold the hexagonal portion of the camshaft with a wrench and remove the camshaft timing sprocket bolt and camshaft timing sprocket from the camshaft.

NOTICE:

Be careful not to damage the camshaft or cylinder head sub-assembly with the wrench.




Hide 11310 47.REMOVE TIMING CHAIN CASE ASSEMBLY

Hide 48.REMOVE NO. 3 CAMSHAFT BEARING CAP

a.
A343548

Remove the 2 camshaft bearing cap bolts and No. 3 camshaft bearing cap from the cylinder head sub-assembly.


Hide 49.REMOVE NO. 1 AND NO. 2 CAMSHAFT BEARING CAP

a.
A347240N01
1.729,0.844 1.99,1 0.26,0.156 10 true 20 1.469,1.802 1.781,2 0.313,0.198 10 false 19 1.219,1.167 1.448,1.333 0.229,0.167 10 true 18 1.479,0.208 1.708,0.375 0.229,0.167 10 false 17 2.344,0.844 2.594,1 0.25,0.156 10 true 16 2.115,1.813 2.375,2.021 0.26,0.208 10 false 15 1.875,1.167 2.104,1.323 0.229,0.156 10 true 14 2.104,0.208 2.344,0.375 0.24,0.167 10 false 13 1.094,0.854 1.313,1.01 0.219,0.156 10 true 12 0.833,1.813 1.094,2.042 0.26,0.229 10 false 11 0.604,1.167 0.833,1.323 0.229,0.156 10 true 10 0.885,0.208 1.052,0.365 0.167,0.156 10 false 9 3.052,0.854 3.198,1.01 0.146,0.156 10 true 8 2.792,1.813 2.99,2 0.198,0.188 10 false 7 2.542,1.167 2.677,1.323 0.135,0.156 10 true 6 2.792,0.208 2.99,0.365 0.198,0.156 10 false 5 0.021,1.125 0.188,1.323 0.167,0.198 10 false 4 0.021,0.854 0.156,1.01 0.135,0.156 10 false 3 0.438,1.896 0.563,2.063 0.125,0.167 10 false 2 0.427,0.104 0.563,0.26 0.135,0.156 10 true 1

Remove the 20 camshaft bearing cap bolts in the sequence shown in the illustration.


b.

Remove the No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 50.REMOVE CAMSHAFT

a.

Remove the camshaft from the cylinder head sub-assembly.


Hide 13512 51.REMOVE NO. 2 CAMSHAFT

a.

Remove the No. 2 camshaft from the cylinder head sub-assembly.


Hide 13801 52.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 16 No. 1 valve rocker arm sub-assemblies from the 16 valve lash adjuster assemblies.


Hide 13750 53.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.


Hide 11101 54.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 13577D 56.REMOVE LOCK PLATE

a.
A343549

Remove the bolt and lock plate from the cylinder block sub-assembly.


Hide 57.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 58.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.