Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › from 2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212880 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

When there is a communication malfunction between the ECM and certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)*, or when the communication ID codes do not match, the ECM stores this DTC.

*: w/ ID Code Box (Immobiliser Code ECU)


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*1):
·

A malfunction in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)*4.

·

A matching communication code cannot be verified during communication between the ECM and certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)*4.


·

Certification ECU (smart key ECU assembly)

·

ECM

·

ID code box (immobiliser code ECU)*4

·

Harness or connector


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: for Automatic Transmission

*3: for Manual Transmission

*4: w/ ID Code Box (Immobiliser Code ECU)


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

w/o ID Code Box (Immobiliser Code ECU):
B413956E05
4.948,2.854 6.75,3.385 1.802,0.531 10 false Certification ECU (Smart Key ECU Assembly) 4.646,1.917 6.448,2.448 1.802,0.531 10 false G17 4.646,1.01 6.448,1.542 1.802,0.531 10 false G16 4.708,0.781 6.51,1.313 1.802,0.531 10 false 3 4.698,1.688 6.5,2.219 1.802,0.531 10 false 35 5.042,1.771 6.854,1.99 1.813,0.219 10 false EFIO 5.042,0.885 6.854,1.104 1.813,0.219 10 false EFII 6,0.229 6.615,0.448 0.615,0.219 10 false +B 1.75,1.469 2.365,1.688 0.615,0.219 10 false +B 1.979,1.792 2.594,2.01 0.615,0.219 10 false IMI 1.99,0.865 2.604,1.083 0.615,0.219 10 false IMO 1.271,2.875 1.885,3.094 0.615,0.219 10 false ECM 2.313,1.01 2.927,1.229 0.615,0.219 10 false G142 2.313,1.917 2.927,2.135 0.615,0.219 10 false G142 2.708,1.01 3.323,1.229 0.615,0.219 10 false G140 2.708,1.917 3.323,2.135 0.615,0.219 10 false G140 3.146,1.917 3.76,2.135 0.615,0.219 10 false G50 3.156,1 3.771,1.219 0.615,0.219 10 false G50 3.51,1 4.125,1.219 0.615,0.219 10 false G145 3.5,1.906 4.115,2.125 0.615,0.219 10 false G145 2.417,2.146 3.031,2.365 0.615,0.219 10 false *1 2.823,2.156 3.417,2.365 0.594,0.208 10 false *2 3.219,2.156 3.813,2.365 0.594,0.208 10 false *3 3.635,2.167 4.229,2.375 0.594,0.208 10 false *4 2.406,1.229 3.021,1.448 0.615,0.219 10 false *1 2.823,1.229 3.417,1.438 0.594,0.208 10 false *2 3.24,1.229 3.833,1.438 0.594,0.208 10 false *3 3.635,1.229 4.229,1.438 0.594,0.208 10 false *4 2.406,1.667 3.021,1.885 0.615,0.219 10 false 10 2.802,1.667 3.417,1.885 0.615,0.219 10 false 30 3.208,1.677 3.823,1.896 0.615,0.219 10 false 16 3.604,1.677 4.219,1.896 0.615,0.219 10 false 10 2.427,0.771 3.042,0.99 0.615,0.219 10 false 9 2.813,0.76 3.427,0.979 0.615,0.219 10 false 29 3.219,0.76 3.833,0.979 0.615,0.219 10 false 17 3.625,0.76 4.24,0.979 0.615,0.219 10 false 8 2.844,2.604 4.844,2.823 2,0.219 10 false *1: for 2TR-FE 2.844,2.896 4.844,3.115 2,0.219 10 false *2: for 1KD-FTV 2.865,3.188 4.865,3.406 2,0.219 10 false *3: for 1GD-FTV, 2GD-FTV 2.854,3.479 4.854,3.698 2,0.219 10 false *4: for 1GR-FE

w/ ID Code Box (Immobiliser Code ECU):
B443338E01
1.24,2.958 1.698,3.156 0.458,0.198 10 false ECM 5,1.01 5.458,1.208 0.458,0.198 10 false EFII 5.01,1.917 5.469,2.115 0.458,0.198 10 false EFIO 4.844,1.01 5.302,1.208 0.458,0.198 10 false 3 4.854,1.917 5.313,2.115 0.458,0.198 10 false 4 2,1.01 2.458,1.208 0.458,0.198 10 false IMO 2.042,1.917 2.5,2.115 0.458,0.198 10 false IMI 2.313,2.01 2.771,2.208 0.458,0.198 10 false G142 2.323,1.104 2.781,1.302 0.458,0.198 10 false G142 2.75,1.104 3.208,1.302 0.458,0.198 10 false G50 2.75,2.021 3.208,2.219 0.458,0.198 10 false G50 3.104,2.01 3.563,2.208 0.458,0.198 10 false G145 3.115,1.104 3.573,1.302 0.458,0.198 10 false G145 2.438,0.906 2.896,1.104 0.458,0.198 10 false 9 2.417,1.802 2.875,2 0.458,0.198 10 false 10 2.802,1.802 3.26,2 0.458,0.198 10 false 16 2.813,0.906 3.271,1.104 0.458,0.198 10 false 17 3.198,1.802 3.677,2.01 0.479,0.208 10 false 10 3.25,0.906 3.708,1.104 0.458,0.198 10 false 8 4.948,3.115 6.792,3.531 1.844,0.417 10 false ID Code Box (Immobiliser Code ECU) 2.396,2.885 4.396,3.094 2,0.208 10 false *1: for 2TR-FE 2.396,3.146 4.396,3.354 2,0.208 10 false *2: for 1GD-FTV, 2GD-FTV 2.396,3.406 4.396,3.615 2,0.208 10 false *3: for 1GR-FE 2.417,1.313 2.875,1.51 0.458,0.198 10 false *1 2.813,1.313 3.271,1.51 0.458,0.198 10 false *2 3.219,1.313 3.677,1.51 0.458,0.198 10 false *3 2.427,2.219 2.885,2.417 0.458,0.198 10 false *1 2.823,2.219 3.281,2.417 0.458,0.198 10 false *2 3.219,2.219 3.677,2.417 0.458,0.198 10 false *3 4.938,2.948 5.396,3.146 0.458,0.198 10 false G138 5.99,0.333 6.448,0.531 0.458,0.198 10 false +B 1.74,1.573 2.198,1.771 0.458,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU)* or ECM, refer to Service Bulletin.

*: w/ ID Code Box (Immobiliser Code ECU)

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output.



Result:
Result Proceed to
OK A
NG (DTC B2799 is output) (w/ ID Code Box [Immobiliser Code ECU]) B
NG (DTC B2799 is output) (w/o ID Code Box [Immobiliser Code ECU]) C
NG (Other DTCs are output) D



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

4.INSPECT ECM (TERMINAL IMO)

C

15.INSPECT ECM (TERMINAL IMO)

D

4.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B443096C01
2.125,0.229 2.583,0.49 0.458,0.26 0.896,0.229 1.354,0.49 0.458,0.26 3.417,0.208 3.875,0.469 0.458,0.26 4.656,0.208 5.115,0.469 0.458,0.26 5.792,0.198 6.25,0.458 0.458,0.26 5.958,1.792 6.417,2.052 0.458,0.26 4.979,1.792 5.438,2.052 0.458,0.26 3.854,1.802 4.313,2.063 0.458,0.26 2.896,1.802 3.354,2.063 0.458,0.26 1.813,1.813 2.271,2.073 0.458,0.26 0.719,1.823 1.177,2.083 0.458,0.26 1.323,3.208 1.781,3.469 0.458,0.26 2.094,3.208 2.552,3.469 0.458,0.26 3.104,3.208 3.563,3.469 0.458,0.26 3.844,3.208 4.302,3.469 0.458,0.26 4.604,3.208 5.063,3.469 0.458,0.26 5.354,3.198 5.813,3.458 0.458,0.26 1.813,4.76 1.948,4.76 1.948,4.76 2.458,3.917 true 4.708,1.729 4.813,1.729 4.813,1.729 5.031,1.167 true 5.802,2.583 6.146,3.094 6.146,3.094 6.25,3.094 true 1.01,6.167 1.469,6.365 0.458,0.198 10 false GND 0.063,0.333 0.375,0.552 0.313,0.219 12 false *A 0.063,1.917 0.365,2.135 0.302,0.219 12 false *B 0.094,3.396 0.427,3.615 0.333,0.219 12 false *C 0.073,0.51 0.385,0.667 0.313,0.156 10 false *a 2.948,6.26 3.26,6.417 0.313,0.156 10 false *b 0.073,2.094 0.385,2.25 0.313,0.156 10 false *a 0.094,3.583 0.406,3.74 0.313,0.156 10 false *a 4.719,3.271 5.104,3.49 0.385,0.219 10 false C83 5.469,3.25 5.854,3.469 0.385,0.219 10 false C82 3.958,3.271 4.344,3.49 0.385,0.219 10 false C84 3.198,3.271 3.583,3.49 0.385,0.219 10 false C85 1.385,3.271 1.802,3.49 0.417,0.219 10 false G144 2.167,3.271 2.583,3.49 0.417,0.219 10 false G145 0.948,0.281 1.365,0.5 0.417,0.219 10 false C146 2.208,0.292 2.625,0.51 0.417,0.219 10 false C147 3.49,0.26 3.906,0.479 0.417,0.219 10 false C148 4.729,0.26 5.146,0.479 0.417,0.219 10 false G142 5.865,0.26 6.281,0.479 0.417,0.219 10 false G143 0.833,1.885 1.25,2.104 0.417,0.219 10 false C38 5.083,1.844 5.5,2.063 0.417,0.219 10 false G49 1.917,1.865 2.333,2.083 0.417,0.219 10 false C39 3.01,1.854 3.427,2.073 0.417,0.219 10 false C40 3.958,1.854 4.375,2.073 0.417,0.219 10 false C41 6.073,1.844 6.49,2.063 0.417,0.219 10 false G50 1.531,4.677 1.844,4.833 0.313,0.156 10 false IMO 4.427,1.656 4.74,1.813 0.313,0.156 10 false IMO 6.292,3.021 6.604,3.177 0.313,0.156 10 false IMO
*A for 2TR-FE *B for 1GD-FTV, 2GD-FTV
*C for 1GR-FE -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1GR-FE

Tester Connection G142-9 (IMO) - Body ground*1
G50-17 (IMO) - Body ground*2
G145-8 (IMO) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

OK:

The waveform is similar to that shown in the illustration.



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or abnormal waveform C



A

5.INSPECT ECM (TERMINAL IMI)

B

11.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

19.REPLACE ECM
5.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B443097C01
0.917,0.333 1.354,0.594 0.438,0.26 2.125,0.313 2.563,0.573 0.438,0.26 3.427,0.323 3.865,0.583 0.438,0.26 4.667,0.323 5.104,0.583 0.438,0.26 5.813,0.313 6.25,0.573 0.438,0.26 5.969,1.833 6.406,2.094 0.438,0.26 4.958,1.844 5.396,2.104 0.438,0.26 3.906,1.854 4.344,2.115 0.438,0.26 2.917,1.844 3.354,2.104 0.438,0.26 1.833,1.833 2.271,2.094 0.438,0.26 0.75,1.854 1.188,2.115 0.438,0.26 1.375,3.219 1.813,3.479 0.438,0.26 2.135,3.208 2.573,3.469 0.438,0.26 3.094,3.208 3.531,3.469 0.438,0.26 3.896,3.198 4.333,3.458 0.438,0.26 4.615,3.198 5.052,3.458 0.438,0.26 5.396,3.208 5.833,3.469 0.438,0.26 5.896,2.573 6.188,3.146 6.188,3.146 6.313,3.146 true 4.677,1.708 4.813,1.708 4.813,1.708 4.938,1.156 true 1.865,4.656 2,4.656 2,4.656 2.219,3.927 true 0.083,0.375 0.427,0.615 0.344,0.24 12 false *A 0.073,1.917 0.406,2.146 0.333,0.229 12 false *B 0.115,3.427 0.448,3.656 0.333,0.229 12 false *C 0.083,0.583 0.396,0.74 0.313,0.156 10 false *a 3.323,6.25 3.635,6.406 0.313,0.156 10 false *b 0.979,6.156 1.292,6.313 0.313,0.156 10 false GND 0.135,3.615 0.448,3.771 0.313,0.156 10 false *a 0.083,2.115 0.396,2.271 0.313,0.156 10 false *a 0.99,0.385 1.406,0.615 0.417,0.229 10 false C146 2.198,0.375 2.646,0.573 0.448,0.198 10 false C147 3.5,0.375 3.885,0.573 0.385,0.198 10 false C148 4.729,0.375 5.135,0.563 0.406,0.188 10 false G142 5.885,0.375 6.292,0.552 0.406,0.177 10 false G143 6.063,1.885 6.469,2.063 0.406,0.177 10 false G50 5.063,1.896 5.469,2.073 0.406,0.177 10 false G49 0.865,1.906 1.271,2.083 0.406,0.177 10 false C38 1.938,1.885 2.344,2.063 0.406,0.177 10 false C39 3.031,1.906 3.438,2.083 0.406,0.177 10 false C40 4.01,1.917 4.417,2.094 0.406,0.177 10 false C41 3.188,3.271 3.594,3.448 0.406,0.177 10 false C85 3.979,3.271 4.385,3.448 0.406,0.177 10 false C84 4.729,3.25 5.135,3.427 0.406,0.177 10 false C83 5.5,3.271 5.906,3.448 0.406,0.177 10 false C82 1.438,3.271 1.844,3.448 0.406,0.177 10 false G144 2.188,3.25 2.594,3.427 0.406,0.177 10 false G145 4.438,1.635 4.844,1.813 0.406,0.177 10 false IMI 6.365,3.073 6.771,3.25 0.406,0.177 10 false IMI 1.656,4.573 2.063,4.75 0.406,0.177 10 false IMI
*A for 2TR-FE *B for 1GD-FTV, 2GD-FTV
*C for 1GR-FE -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1GR-FE

Tester Connection G142-10 (IMI) - Body ground*1
G50-16 (IMI) - Body ground*2
G145-10 (IMI) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

6.REGISTER ECU COMMUNICATION ID

NG

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
6.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER ENGINE STARTS
7.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

8.REPLACE ECM
8.REPLACE ECM
a.

Temporarily replace the ECM with a new one.



Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

11.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

B443098C01
0.979,0.323 1.427,0.563 0.448,0.24 3.531,0.323 3.979,0.563 0.448,0.24 5.813,0.281 6.26,0.521 0.448,0.24 3.938,2.156 4.063,2.156 4.063,2.156 4.323,1.385 true 0.656,2.156 0.781,2.156 0.781,2.156 1.042,1.385 true 5.552,2.177 5.677,2.177 5.677,2.177 5.875,1.313 true 0.396,0.094 0.74,0.302 0.344,0.208 12 false *A 2.906,0.104 3.219,0.333 0.313,0.229 12 false *B 5.156,0.104 5.469,0.458 0.313,0.354 12 false *C 0.396,0.25 0.708,0.406 0.313,0.156 10 false *a 5.167,0.292 5.479,0.448 0.313,0.156 10 false *a 2.917,0.292 3.229,0.448 0.313,0.156 10 false *a 1.042,0.375 1.448,0.604 0.406,0.229 10 false G142 3.646,0.365 4.052,0.594 0.406,0.229 10 false G50 5.885,0.323 6.292,0.552 0.406,0.229 10 false G145 0.375,2.073 0.781,2.302 0.406,0.229 10 false IMO 3.667,2.073 4.073,2.302 0.406,0.229 10 false IMO 5.25,2.083 5.656,2.313 0.406,0.229 10 false IMO
*A for 2TR-FE *B for 1GD-FTV, 2GD-FTV
*C for 1GR-FE - -
*a Front view of wire harness connector
(to ECM)
- -


Standard Voltage:
Tester Connection Condition Result

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1GR-FE

G142-9 (IMO) - Body ground*1
G50-17 (IMO) - Body ground*2
G145-8 (IMO) - Body ground*3
Engine switch on (IG) using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

19.REPLACE ECM
12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the G138 ID code box (immobiliser code ECU) connector.


b.

Disconnect the G142*1, G50*2 or G145*3 ECM connector.

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G138-3 (EFII) - G142-9 (IMO) Always Below 1 Ω
G138-4 (EFIO) - G142-10 (IMI) Always Below 1 Ω
G142-9 (IMO) - Body ground Always 10 kΩ or higher
G138-3 (EFII) - Body ground Always 10 kΩ or higher
G142-10 (IMI) - Body ground Always 10 kΩ or higher
G138-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G138-3 (EFII) - G50-17 (IMO) Always Below 1 Ω
G138-4 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-17 (IMO) - Body ground Always 10 kΩ or higher
G138-3 (EFII) - Body ground Always 10 kΩ or higher
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G138-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G138-3 (EFII) - G145-8 (IMO) Always Below 1 Ω
G138-4 (EFIO) - G145-10 (IMI) Always Below 1 Ω
G145-8 (IMO) - Body ground Always 10 kΩ or higher
G138-3 (EFII) - Body ground Always 10 kΩ or higher
G145-10 (IMI) - Body ground Always 10 kΩ or higher
G138-4 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Recognition code registration is necessary when replacing the ID code box (immobiliser code ECU).

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 2TR-FE)
NG (for 1GD-FTV)
NG (for 2GD-FTV)
NG (for 1GR-FE)



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG (for 2TR-FE)

NG (for 1GD-FTV)

NG (for 2GD-FTV)

NG (for 1GR-FE)

15.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B443099C01
0.938,0.219 1.313,0.469 0.375,0.25 2.177,0.219 2.552,0.469 0.375,0.25 3.448,0.219 3.823,0.469 0.375,0.25 4.698,0.219 5.073,0.469 0.375,0.25 5.844,0.208 6.219,0.458 0.375,0.25 5.354,1.698 5.729,1.948 0.375,0.25 4.167,1.708 4.542,1.958 0.375,0.25 2.76,1.698 3.135,1.948 0.375,0.25 1.5,1.708 1.875,1.958 0.375,0.25 0.771,3.198 1.146,3.448 0.375,0.25 1.854,3.208 2.229,3.458 0.375,0.25 2.938,3.208 3.313,3.458 0.375,0.25 3.906,3.198 4.281,3.448 0.375,0.25 5.021,3.198 5.396,3.448 0.375,0.25 6,3.198 6.375,3.448 0.375,0.25 5.417,4.49 5.792,4.74 0.375,0.25 4.656,4.49 5.031,4.74 0.375,0.25 3.948,4.49 4.323,4.74 0.375,0.25 3.167,4.49 3.542,4.74 0.375,0.25 2.156,4.49 2.531,4.74 0.375,0.25 1.406,4.49 1.781,4.74 0.375,0.25 4.563,3.094 4.656,3.094 4.656,3.094 4.698,2.802 true 4.875,1.625 4.969,1.625 4.969,1.625 5.042,1.063 true 5.406,4.375 5.5,4.375 5.5,4.375 5.792,3.885 true 2.115,5.865 2.208,5.865 2.208,5.865 2.469,5.146 true 0.063,0.146 0.396,0.438 0.333,0.292 12 false *A 0.104,1.865 0.427,2.135 0.323,0.271 12 false *B 0.135,3.177 0.438,3.438 0.302,0.26 12 false *C 0.167,4.625 0.521,4.854 0.354,0.229 12 false *D 0.063,0.323 0.375,0.479 0.313,0.156 10 false *a 2.917,7.26 3.229,7.417 0.313,0.156 10 false *b 0.104,2.031 0.417,2.188 0.313,0.156 10 false *a 0.135,3.344 0.448,3.5 0.313,0.156 10 false *a 0.167,4.792 0.479,4.948 0.313,0.156 10 false *a 1.021,7.177 1.427,7.385 0.406,0.208 10 false GND 4.208,1.76 4.594,1.969 0.385,0.208 10 false G140 5.385,1.75 5.771,1.958 0.385,0.208 10 false G141 1.531,1.76 1.917,1.969 0.385,0.208 10 false C114 2.802,1.75 3.188,1.958 0.385,0.208 10 false C115 0.99,0.26 1.375,0.469 0.385,0.208 10 false C146 2.208,0.26 2.594,0.469 0.385,0.208 10 false C147 3.49,0.271 3.875,0.479 0.385,0.208 10 false C148 4.729,0.271 5.115,0.479 0.385,0.208 10 false G142 5.885,0.271 6.271,0.479 0.385,0.208 10 false G143 0.854,3.24 1.24,3.448 0.385,0.208 10 false C38 1.938,3.25 2.323,3.458 0.385,0.208 10 false C39 3.021,3.24 3.406,3.448 0.385,0.208 10 false C40 3.969,3.25 4.354,3.458 0.385,0.208 10 false C41 5.104,3.24 5.49,3.448 0.385,0.208 10 false G49 6.083,3.24 6.469,3.448 0.385,0.208 10 false G50 3.25,4.542 3.635,4.75 0.385,0.208 10 false C85 4.042,4.531 4.427,4.74 0.385,0.208 10 false C84 4.729,4.531 5.115,4.74 0.385,0.208 10 false C83 5.49,4.542 5.875,4.75 0.385,0.208 10 false C82 1.438,4.531 1.844,4.729 0.406,0.198 10 false G144 2.188,4.531 2.594,4.729 0.406,0.198 10 false G145 4.594,1.552 4.979,1.76 0.385,0.208 10 false IMO 4.292,3.021 4.677,3.229 0.385,0.208 10 false IMO 5.135,4.302 5.521,4.51 0.385,0.208 10 false IMO 1.833,5.781 2.219,5.99 0.385,0.208 10 false IMO
*A for 2TR-FE *B for 1KD-FTV
*C for 1GD-FTV, 2GD-FTV *D for 1GR-FE
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content

*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE

Tester Connection G142-9 (IMO) - Body ground*1
G140-29 (IMO) - Body ground*2
G50-17 (IMO) - Body ground*3
G145-8 (IMO) - Body ground*4
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

OK:

The waveform is similar to that shown in the illustration.



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or abnormal waveform C



A

16.INSPECT ECM (TERMINAL IMI)

B

22.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

19.REPLACE ECM
16.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B443100C01
0.958,0.229 1.333,0.479 0.375,0.25 2.188,0.229 2.563,0.479 0.375,0.25 3.469,0.229 3.844,0.479 0.375,0.25 4.688,0.24 5.063,0.49 0.375,0.25 5.844,0.24 6.219,0.49 0.375,0.25 5.323,1.719 5.698,1.969 0.375,0.25 4.167,1.729 4.542,1.979 0.375,0.25 2.771,1.719 3.146,1.969 0.375,0.25 1.5,1.719 1.875,1.969 0.375,0.25 0.76,3.177 1.135,3.427 0.375,0.25 1.823,3.177 2.198,3.427 0.375,0.25 2.938,3.188 3.313,3.438 0.375,0.25 3.917,3.188 4.292,3.438 0.375,0.25 4.99,3.177 5.365,3.427 0.375,0.25 6,3.188 6.375,3.438 0.375,0.25 5.385,4.479 5.76,4.729 0.375,0.25 4.667,4.49 5.042,4.74 0.375,0.25 3.917,4.479 4.292,4.729 0.375,0.25 3.146,4.479 3.521,4.729 0.375,0.25 2.177,4.49 2.552,4.74 0.375,0.25 1.417,4.479 1.792,4.729 0.375,0.25 4.646,1.615 4.771,1.615 4.771,1.615 4.938,1.063 true 4.333,3.073 4.458,3.073 4.458,3.073 4.573,2.792 true 5.885,3.865 6.052,4.385 6.052,4.385 6.167,4.385 true 1.833,5.875 1.958,5.875 1.958,5.875 2.208,5.146 true 0.083,0.219 0.406,0.427 0.323,0.208 12 false *A 0.094,1.75 0.396,1.948 0.302,0.198 12 false *B 0.104,3.146 0.469,3.375 0.365,0.229 12 false *C 0.146,4.542 0.448,4.76 0.302,0.219 12 false *D 0.094,0.396 0.406,0.552 0.313,0.156 10 false *a 3.323,7.281 3.635,7.438 0.313,0.156 10 false *b 0.094,1.927 0.406,2.083 0.313,0.156 10 false *a 0.115,3.313 0.427,3.469 0.313,0.156 10 false *a 0.156,4.75 0.469,4.906 0.313,0.156 10 false *a 1,7.177 1.344,7.375 0.344,0.198 10 false GND 1,0.271 1.354,0.458 0.354,0.188 10 false C146 2.219,0.281 2.573,0.469 0.354,0.188 10 false C147 3.521,0.292 3.875,0.479 0.354,0.188 10 false C148 4.729,0.292 5.083,0.479 0.354,0.188 10 false G142 5.875,0.302 6.229,0.49 0.354,0.188 10 false G143 1.552,1.781 1.906,1.969 0.354,0.188 10 false C114 2.833,1.781 3.188,1.969 0.354,0.188 10 false C115 4.198,1.771 4.552,1.958 0.354,0.188 10 false G140 5.365,1.771 5.719,1.958 0.354,0.188 10 false G141 0.844,3.229 1.198,3.417 0.354,0.188 10 false C38 1.906,3.219 2.26,3.406 0.354,0.188 10 false C39 3.01,3.229 3.365,3.417 0.354,0.188 10 false C40 3.99,3.24 4.344,3.427 0.354,0.188 10 false C41 5.073,3.219 5.427,3.406 0.354,0.188 10 false G49 6.083,3.24 6.438,3.427 0.354,0.188 10 false G50 1.448,4.531 1.802,4.719 0.354,0.188 10 false G144 2.219,4.531 2.573,4.719 0.354,0.188 10 false G145 3.229,4.521 3.583,4.708 0.354,0.188 10 false C85 3.99,4.521 4.344,4.708 0.354,0.188 10 false C84 4.74,4.531 5.094,4.719 0.354,0.188 10 false C83 5.448,4.521 5.802,4.708 0.354,0.188 10 false C82 4.417,1.542 4.771,1.729 0.354,0.188 10 false IMI 4.135,3.01 4.49,3.198 0.354,0.188 10 false IMI 6.208,4.302 6.563,4.49 0.354,0.188 10 false IMI 1.615,5.792 1.969,5.979 0.354,0.188 10 false IMI
*A for 2TR-FE *B for 1KD-FTV
*C for 1GD-FTV, 2GD-FTV *D for 1GR-FE
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content

*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE

Tester Connection G142-10 (IMI) - Body ground*1
G140-30 (IMI) - Body ground*2
G50-16 (IMI) - Body ground*3
G145-10 (IMI) - Body ground*4
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected


OK:

The waveform is similar to that shown in the illustration.


Result:
Proceed to
OK
NG



OK

17.REGISTER ECU COMMUNICATION ID

NG

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
17.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER ENGINE STARTS
18.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

19.REPLACE ECM
19.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

20.REGISTER ECU COMMUNICATION ID
20.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER ENGINE STARTS
21.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

22.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

B413960C05
0.844,0.396 1.24,0.656 0.396,0.26 2.615,0.396 3.01,0.656 0.396,0.26 4.458,0.406 4.854,0.667 0.396,0.26 6.063,0.24 6.458,0.5 0.396,0.26 0.792,1.406 1.073,2.24 1.073,2.24 1.229,2.24 true 2.385,1.719 2.552,2.229 2.552,2.229 2.708,2.229 true 5.24,1.427 5.042,2.198 5.042,2.198 4.875,2.198 true 6.125,1.323 5.917,2.177 5.917,2.177 5.75,2.177 true 0.094,0.208 0.406,0.406 0.313,0.198 10 false *a 0.104,0.042 0.417,0.24 0.313,0.198 12 false *A 1.906,0.031 2.219,0.229 0.313,0.198 12 false *B 3.719,0.042 4.031,0.24 0.313,0.198 12 false *C 5.521,0.052 5.833,0.25 0.313,0.198 12 false *D 1.927,0.198 2.24,0.396 0.313,0.198 10 false *a 3.75,0.208 4.063,0.406 0.313,0.198 10 false *a 5.542,0.219 5.854,0.417 0.313,0.198 10 false *a 1.271,2.167 1.729,2.365 0.458,0.198 10 false IMO 2.76,2.156 3.219,2.354 0.458,0.198 10 false IMO 4.594,2.125 5.052,2.323 0.458,0.198 10 false IMO 5.479,2.104 5.938,2.302 0.458,0.198 10 false IMO 0.885,0.438 1.344,0.635 0.458,0.198 10 false G142 2.667,0.448 3.125,0.646 0.458,0.198 10 false G140 4.531,0.458 4.99,0.656 0.458,0.198 10 false G50 6.104,0.292 6.563,0.49 0.458,0.198 10 false G145
*A for 2TR-FE *B for 1KD-FTV
*C for 1GD-FTV, 2GD-FTV *D for 1GR-FE
*a Front view of wire harness connector
(to ECM)
- -


Standard Voltage:
Tester Connection Condition Result

*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE

G142-9 (IMO) - Body ground*1
G140-29 (IMO) - Body ground*2
G50-17 (IMO) - Body ground*3
G145-8 (IMO) - Body ground*4
Engine switch on (IG) using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

B

19.REPLACE ECM
23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G142*1, G140*2, G50*3 or G145*4 ECM connector.

*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G16-3 (EFII) - G142-9 (IMO) Always Below 1 Ω
G17-35 (EFIO) - G142-10 (IMI) Always Below 1 Ω
G142-9 (IMO) - Body ground Always 10 kΩ or higher
G16-3 (EFII) - Body ground Always 10 kΩ or higher
G142-10 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G16-3 (EFII) - G140-29 (IMO) Always Below 1 Ω
G17-35 (EFIO) - G140-30 (IMI) Always Below 1 Ω
G140-29 (IMO) - Body ground Always 10 kΩ or higher
G16-3 (EFII) - Body ground Always 10 kΩ or higher
G140-30 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G16-3 (EFII) - G50-17 (IMO) Always Below 1 Ω
G17-35 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-17 (IMO) - Body ground Always 10 kΩ or higher
G16-3 (EFII) - Body ground Always 10 kΩ or higher
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G16-3 (EFII) - G145-8 (IMO) Always Below 1 Ω
G17-35 (EFIO) - G145-10 (IMI) Always Below 1 Ω
G145-8 (IMO) - Body ground Always 10 kΩ or higher
G16-3 (EFII) - Body ground Always 10 kΩ or higher
G145-10 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Recognition code registration is necessary when replacing the certification ECU (smart key ECU assembly).

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

25.CHECK WHETHER ENGINE STARTS
25.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 2TR-FE)
NG (for 1KD-FTV)
NG (for 1GD-FTV)
NG (for 2GD-FTV)
NG (for 1GR-FE)



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG (for 2TR-FE)

NG (for 1KD-FTV)

NG (for 1GD-FTV)

NG (for 2GD-FTV)

NG (for 1GR-FE)