Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › from 2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212880 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)* is stuck high, the ECM stores this DTC.

*: w/ ID Code Box (Immobiliser Code ECU)


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)*2 is stuck high (1 trip detection logic*1).
·

Harness or connector

·

Certification ECU (smart key ECU assembly)

·

ID code box (immobiliser code ECU)*2

·

ECM


DTC output confirmation operation:

Turn the engine switch on (IG) and wait 6 seconds.



*1: Only output while a malfunction is present.

*2: w/ ID Code Box (Immobiliser Code ECU)


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

w/o ID Code Box (Immobiliser Code ECU):
B413961E05
4.927,2.073 6.708,2.594 1.781,0.521 10 false Certification ECU (Smart Key ECU Assembly) 5.021,0.844 6.802,1.365 1.781,0.521 10 false EFIO 4.948,1.896 5.333,2.156 0.385,0.26 10 false G17 4.771,0.844 6.552,1.365 1.781,0.521 10 false 35 2.313,0.948 2.698,1.208 0.385,0.26 10 false G142 2.698,0.948 3.083,1.208 0.385,0.26 10 false G140 3.146,0.948 3.531,1.208 0.385,0.26 10 false G50 3.5,0.948 3.885,1.208 0.385,0.26 10 false G145 1.75,0.521 2.135,0.781 0.385,0.26 10 false +B 2.396,0.729 2.76,0.917 0.365,0.188 10 false 10 2.802,0.729 3.167,0.917 0.365,0.188 10 false 30 3.208,0.719 3.573,0.906 0.365,0.188 10 false 16 3.583,0.729 3.948,0.917 0.365,0.188 10 false 10 2.417,1.188 2.781,1.375 0.365,0.188 10 false *1 2.833,1.188 3.198,1.375 0.365,0.188 10 false *2 3.229,1.177 3.594,1.365 0.365,0.188 10 false *3 3.604,1.188 3.969,1.375 0.365,0.188 10 false *4 1.292,1.906 1.969,2.083 0.677,0.177 10 false ECM 2.698,1.635 4.146,1.833 1.448,0.198 10 false *1: for 2TR-FE 2.698,1.896 4.469,2.156 1.771,0.26 10 false *2: for 1KD-FTV 2.698,2.156 4.438,2.417 1.74,0.26 10 false *3: for 1GD-FTV, 2GD-FTV 2.708,2.406 4.156,2.604 1.448,0.198 10 false *4: for 1GR-FE 2.031,0.833 3.813,1.354 1.781,0.521 10 false IMI

w/ ID Code Box (Immobiliser Code ECU):
B443339E01
1.292,1.906 1.75,2.104 0.458,0.198 10 false ECM 4.99,2.031 6.802,2.458 1.813,0.427 10 false ID Code Box (Immobiliser Code ECU) 2.313,0.958 2.771,1.156 0.458,0.198 10 false G142 1.771,0.521 2.229,0.719 0.458,0.198 10 false +B 2.76,0.958 3.219,1.156 0.458,0.198 10 false G50 3.115,0.958 3.573,1.156 0.458,0.198 10 false G145 2.396,1.177 2.854,1.375 0.458,0.198 10 false *1 2.823,1.177 3.281,1.375 0.458,0.198 10 false *2 3.198,1.177 3.656,1.375 0.458,0.198 10 false *3 2.385,1.854 4.188,2.01 1.802,0.156 10 false *1: for 2TR-FE 2.385,2.125 4.229,2.292 1.844,0.167 10 false *2: for 1GD-FTV, 2GD-FTV 2.385,2.396 4.229,2.563 1.844,0.167 10 false *3: for 1GR-FE 2.385,0.76 2.844,0.958 0.458,0.198 10 false 10 2.813,0.76 3.271,0.958 0.458,0.198 10 false 16 4.958,1.865 5.417,2.063 0.458,0.198 10 false G138 5.01,0.865 5.469,1.063 0.458,0.198 10 false EFIO 3.188,0.76 3.646,0.958 0.458,0.198 10 false 10 4.844,0.865 5.302,1.063 0.458,0.198 10 false 4 2.042,0.875 2.5,1.073 0.458,0.198 10 false IMI

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU)* or ECM, refer to Service Bulletin.

*: w/ ID Code Box (Immobiliser Code ECU)

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B279A and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the engine switch on (IG) and wait 10 seconds.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

If DTCs other than DTC B279A are output, troubleshoot those DTCs first.



Result:
Result Proceed to
DTC B279A is not output (w/ ID Code Box [Immobiliser Code ECU]) A
DTC B279A is not output (w/o ID Code Box [Immobiliser Code ECU]) B
DTC B279A and other DTCs are output C



A

3.CHECK CONNECTION OF CONNECTOR

B

10.CHECK CONNECTION OF CONNECTOR

C

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the G138 ID code box (immobiliser code ECU) connector.


b.

Disconnect the G142*1, G50*2 or G145*3 ECM connector.

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G138-4 (EFIO) - G142-10 (IMI) Always Below 1 Ω
G142-10 (IMI) - Body ground Always 10 kΩ or higher
G138-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G138-4 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G138-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G138-4 (EFIO) - G145-10 (IMI) Always Below 1 Ω
G145-10 (IMI) - Body ground Always 10 kΩ or higher
G138-4 (EFIO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 2TR-FE
Tester Connection Condition Specified Condition
G142-10 (IMI) - Body ground Always Below 1 V

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G50-16 (IMI) - Body ground Always Below 1 V

for 1GR-FE
Tester Connection Condition Specified Condition
G145-10 (IMI) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Recognition code registration is necessary when replacing the ID code box (immobiliser code ECU).

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.REGISTER RECOGNITION CODES
6.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A is not output.



Result:
Proceed to
OK
NG (for 2TR-FE)
NG (for 1GD-FTV)
NG (for 2GD-FTV)
NG (for 1GR-FE)



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG (for 2TR-FE)

NG (for 1GD-FTV)

NG (for 2GD-FTV)

NG (for 1GR-FE)

10.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

NG

CONNECT CONNECTORS PROPERLY

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G142*1, G140*2, G50*3 or G145*4 ECM connector.

*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G17-35 (EFIO) - G142-10 (IMI) Always Below 1 Ω
G142-10 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G17-35 (EFIO) - G140-30 (IMI) Always Below 1 Ω
G140-30 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G17-35 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G17-35 (EFIO) - G145-10 (IMI) Always Below 1 Ω
G145-10 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 2TR-FE
Tester Connection Condition Specified Condition
G142-10 (IMI) - Body ground Always Below 1 V

for 1KD-FTV
Tester Connection Condition Specified Condition
G140-30 (IMI) - Body ground Always Below 1 V

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G50-16 (IMI) - Body ground Always Below 1 V

for 1GR-FE
Tester Connection Condition Specified Condition
G145-10 (IMI) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

13.REGISTER RECOGNITION CODES
13.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.REGISTER ECU COMMUNICATION ID
14.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A is not output.



Result:
Proceed to
OK
NG (for 2TR-FE)
NG (for 1KD-FTV)
NG (for 1GD-FTV)
NG (for 2GD-FTV)
NG (for 1GR-FE)



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG (for 2TR-FE)

NG (for 1KD-FTV)

NG (for 1GD-FTV)

NG (for 2GD-FTV)

NG (for 1GR-FE)