Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › from 2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212879 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the driver door only, but the entry lock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the driver door lock position switch system.

WIRING DIAGRAM

B406561E05
5.917,1.219 6.531,1.417 0.615,0.198 10 false PRG3 5.917,1.698 6.531,1.896 0.615,0.198 10 false RDA3 5.604,1.104 6.219,1.302 0.615,0.198 10 false 36 5.615,1.583 6.229,1.781 0.615,0.198 10 false 13 5.052,1.104 5.667,1.302 0.615,0.198 10 false 9 5.052,1.594 5.667,1.792 0.615,0.198 10 false 16 4.604,1.208 5.219,1.406 0.615,0.198 10 false PRG 4.615,1.708 5.229,1.906 0.615,0.198 10 false RDA 3.115,1.333 3.729,1.531 0.615,0.198 10 false LSWD 2.823,1.333 3.438,1.531 0.615,0.198 10 false 15 2.167,1.333 2.781,1.531 0.615,0.198 10 false 8*1, 7*2 1.677,1.333 2.292,1.531 0.615,0.198 10 false LSSR 0.74,1.333 1.354,1.531 0.615,0.198 10 false E 0.125,1.333 0.74,1.531 0.615,0.198 10 false 7*1, 8*2 0.385,2.042 2.073,2.49 1.688,0.448 10 false Front Door Lock Assembly (for Driver Door) 3.979,1.042 4.594,1.24 0.615,0.198 10 false +B 0.385,1.885 1.906,2.115 1.521,0.229 10 false K1*1, J1*2 3.552,2.479 4.219,2.646 0.667,0.167 10 false G33 3.563,2.646 4.896,2.896 1.333,0.25 10 false Body ECU 5.458,2.49 6.125,2.656 0.667,0.167 10 false G17 5.479,2.646 7.031,3.25 1.552,0.604 10 false Certification ECU (Smart Key ECU Assembly) 0.104,3.052 1.625,3.281 1.521,0.229 10 false *1: for LHD 0.104,3.323 1.635,3.5 1.531,0.177 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).

While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window master switch is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly), body ECU and door lock assembly before performing the inspection.


OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR) (LOCK POSITION SWITCH)

NG

2.INSPECT FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR) (LOCK POSITION SWITCH)
a.

Remove the front door lock assembly (for Driver Door).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.

Inspect the front door lock assembly (for Driver Door).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR) - BODY ECU AND BODY GROUND)

NG

REPLACE FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR)

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR) - BODY ECU AND BODY GROUND)
a.

Disconnect the K1*1 or J1*2 front door lock assembly (for Driver Door) connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G33 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K1-8 (LSSR) - G33-15 (LSWD) Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
K1-8 (LSSR) or G33-15 (LSWD) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J1-7 (LSSR) - G33-15 (LSWD) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
J1-7 (LSSR) or G33-15 (LSWD) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

4.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the entry lock/unlock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly), body ECU and front door lock assembly (for Driver Door) before performing the inspection.


OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

NG

5.REPLACE BODY ECU
5.REPLACE BODY ECU
a.

Replace the body ECU with a new or known good one.



Result:
Proceed to
NEXT



NEXT

6.CHECK ENTRY DOOR LOCK OPERATION
6.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the entry lock/unlock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

END (BODY ECU WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)