When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
No. 3 injection pipe sub-assembly ·
No. 4 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing Gear Case Assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
11322A
1.REMOVE NO. 1 TIMING BELT COVER
13568
2.REMOVE TIMING BELT
13505
3.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
13408
4.REMOVE CRANKSHAFT PULLEY SUB-ASSEMBLY
12278
5.REMOVE VENTILATION HOSE HEAT INSULATOR
Remove the 2 bolts and ventilation hose heat insulator from the cylinder head sub-assembly.
6.REMOVE EXHAUST MANIFOLD WITH TURBOCHARGER
88440D
7.REMOVE NO. 2 IDLE PULLEY ASSEMBLY
27020
8.REMOVE GENERATOR ASSEMBLY
12511C
9.REMOVE GENERATOR BRACKET
Remove the bolt and generator bracket.
16620
10.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 4 bolts and V-ribbed belt tensioner assembly from the cylinder block sub-assembly.
88431
11.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly.
16321
12.REMOVE WATER INLET
16331A
13.REMOVE THERMOSTAT
16331
14.REMOVE WATER OUTLET
Remove the 2 bolts, water outlet and gasket from the cylinder head sub-assembly.
26100G
15.REMOVE DIESEL THROTTLE BODY ASSEMBLY
17111
16.REMOVE INTAKE MANIFOLD
25617A
17.REMOVE NO. 2 EGR HOLE COVER PLATE
Remove the 2 nuts and No. 2 EGR hole cover plate.
Remove the gasket.
19850
18.REMOVE GLOW PLUG ASSEMBLY
23810A
19.REMOVE COMMON RAIL ASSEMBLY
22100
20.REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY
15701C
21.REMOVE OIL COOLER COVER SUB-ASSEMBLY
29300
22.REMOVE VACUUM PUMP ASSEMBLY
Remove the 2 nuts, vacuum pump assembly and 2 O-rings from the timing gear cover.
44320
23.REMOVE VANE PUMP ASSEMBLY
Remove the 2 nuts, vane pump assembly and O-ring from the timing gear case assembly.
24.REMOVE CRANKSHAFT POSITION SENSOR
25.REMOVE CAMSHAFT POSITION SENSOR
26.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
12311
27.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH
| *a | LH Side |
| *b | RH Side |
Remove the 4 bolts and front No. 1 engine mounting bracket RH from the cylinder block sub-assembly.
12315
28.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
Remove the 4 bolts and front No. 1 engine mounting bracket LH from th cylinder block sub-assembly.