When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. Upon receiving the signal, the ECM cancels the cruise control system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0571 | Brake Switch "A" Circuit | When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds or more | ·
Stop light switch assembly ·
ECM ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-2 (GND) -Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-6 (B) - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |
| A64-7 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A64 stop light switch assembly connector.
Disconnect the G145*1, G143*2, G50*3 or G140*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV
for Automatic Transmission:
w/ Smart Entry and Start System:
Disconnect the I4 shift lock control ECU connector.
w/o Smart Entry and Start System:
Disconnect the I6 shift lock control ECU connector.
w/ Vehicle Stability Control System:
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
w/ Smart Entry and Start System:
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
for 1KD-FTV:
Disconnect the G147 TCM connector.
Measure the resistance according to the value(s) in the table below.
for 1GR-FE:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G145-34 (ST1-) - A64-5 (L) | Always | Below 1 Ω |
| G145-35 (STP) - A64-3 (L) | Always | Below 1 Ω |
| G145-34 (ST1-) or A64-5 (L) - Body ground | Always | 10 kΩ or higher |
| G145-35 (STP) or A64-3 (L) - Body ground | Always | 10 kΩ or higher |
for 2TR-FE:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G143-11 (ST1-) - A64-5 (L) | Always | Below 1 Ω |
| G143-10 (STP) - A64-3 (L) | Always | Below 1 Ω |
| G143-11 (ST1-) or A64-5 (L) - Body ground | Always | 10 kΩ or higher |
| G143-10 (STP) or A64-3 (L) - Body ground | Always | 10 kΩ or higher |
for 1GD-FTV, 2GD-FTV:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G50-12 (ST1-) - A64-5 (L) | Always | Below 1 Ω |
| G50-13 (STP) - A64-3 (L) | Always | Below 1 Ω |
| G50-12 (ST1-) or A64-5 (L) - Body ground | Always | 10 kΩ or higher |
| G50-13 (STP) or A64-3 (L) - Body ground | Always | 10 kΩ or higher |
for 1KD-FTV:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G140-14 (ST1-) - A64-5 (L) | Always | Below 1 Ω |
| G140-15 (STP) - A64-3 (L) | Always | Below 1 Ω |
| G140-14 (ST1-) or A64-5 (L) - Body ground | Always | 10 kΩ or higher |
| G140-15 (STP) or A64-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G145-34 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | Below 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| G145-35 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V |
for 2TR-FE
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G143-11 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | Below 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| G143-10 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V |
for 1GD-FTV, 2GD-FTV
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G50-12 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| G50-13 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | 0 to 1.5 V |
for 1KD-FTV
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G140-14 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| G140-15 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | 0 to 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>REMOVAL
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
NG