Turn the ignition switch to ON.
except Pre-Runner:
Finish switching to L4.
Check the rear differential lock indicator light.
Press the differential lock switch.
After 60 seconds, check the rear differential lock indicator light.
| Result | Proceed to |
|---|---|
| Rear differential lock indicator light blinks or illuminates | A |
| Rear differential lock indicator light remains off regardless of switch operation | B |
| Rear differential lock indicator light remains illuminated regardless of switch operation | C |
| Rear differential lock indicator light rapidly blinks | D |
Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
Rapidly blinking: Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
A
B
C
D
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
"Bus Check" indicates no malfunctions in CAN communication.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Differential Lock Control SW (R) | Differential lock switch status (differential lock switch input signal of R terminal on ECU side) | ON or OFF | ON: Switch pressed and held
OFF: Switch not pressed |
- |
| Tester Display |
|---|
| Rear Differential Lock Control SW (R) |
Display changes according to differential lock switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Perform Active Test of the combination meter assembly using the GTS.
| Tester Display |
|---|
| Indicat. Rr DIFF LOCK |
Check the combination meter assembly.
The rear differential lock indicator light turns on or off in accordance with the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the differential lock switch.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH>REMOVAL
Inspect the differential lock switch.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH>INSPECTION
The differential lock switch operates normally.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the C60 4 wheel drive control ECU connector.
Disconnect the G58 differential lock switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C60-15 (R) - G58-6 (B) | Always | Below 1 Ω |
| G58-3 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
"Bus Check" indicates no malfunctions in CAN communication.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Differential Lock Indicator Request | Rear differential lock indicator light request | Blink4*, Blink3, Blink2, Blink1, ON or OFF | ·
Blink3: Indicator light rapidly blinks ·
Blink2: Indicator light blinks 3 times ·
Blink1: Indicator light blinks ·
ON: Indicator light illuminates ·
OFF: Indicator light turns off |
·
Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off) ·
Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off) *: Item not supported, therefore not displayed |
| Tester Display |
|---|
| Rear Differential Lock Indicator Request |
except Pre-Runner:
Finish switching to L4.
Turn the differential lock switch on and off several times and check the GTS display condition of the rear differential lock indicator light.
| Result | Proceed to |
|---|---|
| Data List continues to display ON even when differential lock switch is operated | A |
| Data List display changes according to differential lock switch operation | B |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING