Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2016.01
RM3270E _56 Audio / Visual / Telematics _041699 AUDIO / VIDEO _0249874 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Broadcast cannot be Received (Bad Reception)  


WIRING DIAGRAM

E321037E02
1.156,0.375 5.74,0.573 4.583,0.198 10 false No. 1 Amplifier Antenna Assembly 1.646,0.927 1.781,1.104 0.135,0.177 10 false 2 1.646,1.313 1.781,1.49 0.135,0.177 10 false 1 3.104,0.948 3.24,1.125 0.135,0.177 10 false 2 4.542,0.938 4.677,1.115 0.135,0.177 10 false 2 3.094,1.333 3.229,1.51 0.135,0.177 10 false 3 4.552,1.323 4.688,1.5 0.135,0.177 10 false 3 5.594,0.927 5.729,1.104 0.135,0.177 10 false 3 6.052,1.042 6.625,1.219 0.573,0.177 10 false MAIN 5.583,1.333 5.719,1.51 0.135,0.177 10 false 5 4.135,0.958 4.281,1.219 0.146,0.26 10 false 2 6.052,1.552 6.625,1.729 0.573,0.177 10 false ANT+ 4.135,1.313 4.281,1.573 0.146,0.26 10 false 3 1.469,1.865 2.75,2.208 1.281,0.344 10 false No. 3 Antenna Cord Sub-assembly 4.667,1.885 5.573,2.24 0.906,0.354 10 false Antenna Cord Sub-assembly 2.688,0.927 2.823,1.104 0.135,0.177 10 false 2 2.677,1.344 2.813,1.521 0.135,0.177 10 false 3 5.948,1.906 6.521,2.083 0.573,0.177 10 false RA 5.979,2.073 6.938,2.438 0.958,0.365 10 false Radio Receiver Assembly 3.125,1.885 4.406,2.229 1.281,0.344 10 false No. 2 Antenna Cord Sub-assembly

PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without the permission of the customer.



Result:
Proceed to
OK
NG



OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK RADIO RECEIVER ASSEMBLY
3.CHECK RADIO RECEIVER ASSEMBLY
a.
E276819

Remove the antenna connector from the radio receiver assembly.


b.

Turn the ignition switch ACC with the radio receiver assembly connector connected.


c.

Turn the radio on and tune into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

4.INSPECT RADIO RECEIVER ASSEMBLY
a.
E188455E31
1.552,1.104 1.146,1.479 true 0.844,1.51 1.24,1.677 0.396,0.167 10 ANT+

Disconnect the RA radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC, radio switch on and FM or AM selected 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

5.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E318869C01
0.479,0.823 0.948,1.073 0.469,0.25 0.979,1.552 1.135,1.552 1.135,1.552 1.458,1.208 true 1.906,0.969 2.125,0.781 2.125,0.781 2.292,0.781 true 0.135,0.094 0.448,0.25 0.313,0.156 10 false *a 0.125,1.917 0.438,2.073 0.313,0.156 10 false *b 0.604,0.854 0.917,1.01 0.313,0.156 10 false RA 2.354,0.656 2.865,0.917 0.51,0.26 10 false ANT+ 0.563,1.448 1.073,1.708 0.51,0.26 10 false MAIN
*a Front view of wire harness connector
(to Radio Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Remove the antenna connector from the radio receiver assembly.


b.

Remove the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 2 Always Below 1 Ω
RA-5 (ANT+) - 3 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E318870C01
0.198,0.135 0.51,0.292 0.313,0.156 10 false *a 0.115,1.969 0.427,2.125 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Remove the antenna connector from the antenna cord sub-assembly.


b.

Remove the antenna connector from the No. 3 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 2 Always Below 1 Ω
3 - 3 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E318871C01
0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.146,1.781 0.458,1.938 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Antenna Amplifier Assembly)


Remove the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Remove the antenna connector from the No. 1 antenna amplifier assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 2 Always Below 1 Ω
3 - 1 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO RECEIVER ASSEMBLY