Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0198095 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder  


DESCRIPTION

The body ECU receives switch signals from the power window regulator master switch assembly and driver door key cylinder lock or unlock switch signals from the front door lock assembly RH. The body ECU activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

w/o Smart Entry and Start System
E322030E10
1.385,1.073 2.615,1.271 1.229,0.198 10 false 1*1, 9*2 2,1.073 3.229,1.271 1.229,0.198 10 false E 2.854,0.802 3,1.021 0.146,0.219 10 false L 3.052,0.802 3.719,1.052 0.667,0.25 10 false 2*1, 8*2 2.792,1.365 3.115,1.583 0.323,0.219 10 false UL 3.063,1.344 3.729,1.594 0.667,0.25 10 false 8*1, 2*2 1.719,1.813 3.167,2 1.448,0.188 10 false K15*1, J14*2 1.74,1.99 3.76,2.313 2.021,0.323 10 false Power Window Regulator Master Switch Assembly 1.396,3.052 2.625,3.25 1.229,0.198 10 false 7*1, 8*2 1.99,3.052 3.219,3.25 1.229,0.198 10 false E 3.063,2.792 3.729,3.042 0.667,0.25 10 false 9*1, 6*2 3.083,3.354 4.125,3.542 1.042,0.188 10 false 10*1, 5*2 2.854,2.802 3,3.021 0.146,0.219 10 false L 2.792,3.354 3.115,3.573 0.323,0.219 10 false UL 1.604,3.813 2.833,4.021 1.229,0.208 10 false K1*1, J1*2 1.594,3.979 4.323,4.198 2.729,0.219 10 false Front Door Lock Assembly LH*1, RH*2 4.708,0.813 4.99,1.042 0.281,0.229 10 false 19 4.719,1.354 5,1.583 0.281,0.229 10 false 12 4.719,2.771 5,3 0.281,0.229 10 false 18 4.708,3.354 5.406,3.583 0.698,0.229 10 false 11 4.979,0.802 5.302,1.021 0.323,0.219 10 false L1 5,1.375 5.49,1.594 0.49,0.219 10 false UL1 5,2.802 5.323,3.021 0.323,0.219 10 false L2 4.979,3.344 5.927,3.573 0.948,0.229 10 false UL2 5.052,4.083 5.625,4.313 0.573,0.229 10 false G33 5.052,4.219 6.563,4.406 1.51,0.188 10 false Body ECU 5.708,0.448 6.031,0.667 0.323,0.219 10 false +B 6.302,0.438 6.625,0.656 0.323,0.219 10 false +B 6.333,2.396 6.656,2.615 0.323,0.219 10 false +B 5.729,2.396 6.052,2.615 0.323,0.219 10 false +B 0.135,4.25 1.583,4.438 1.448,0.188 10 false *1: for LHD 0.135,4.51 1.583,4.698 1.448,0.188 10 false *2: for RHD


w/ Smart Entry and Start System
E322031E07
1.365,1.896 3.052,2.094 1.688,0.198 10 false K16*1, J5*2 1.365,2.063 3.375,2.417 2.01,0.354 10 false Power Window Regulator Master Switch Assembly 2.271,1.073 2.417,1.292 0.146,0.219 10 false IC 2.833,0.917 3.198,1.094 0.365,0.177 10 false LIN1 3.219,0.927 3.583,1.104 0.365,0.177 10 false 17 4.771,0.896 5.135,1.073 0.365,0.177 10 false 3 5.031,1.083 5.396,1.26 0.365,0.177 10 false LIN2 1.531,3.042 3.031,3.229 1.5,0.188 10 false 7*1, 8*2 2.167,3.063 2.375,3.26 0.208,0.198 10 false E 3,2.792 3.208,2.99 0.208,0.198 10 false L 2.927,3.333 3.271,3.51 0.344,0.177 10 false UL 3.219,2.792 4.719,2.979 1.5,0.188 10 false 9*1, 6*2 3.208,3.354 4.708,3.542 1.5,0.188 10 false 10*1, 5*2 1.719,3.802 3.219,3.99 1.5,0.188 10 false K1*1, J1*2 1.719,3.958 4.271,4.135 2.552,0.177 10 false Front Door Lock Assembly LH*1, RH*2 0.656,4.292 3.208,4.469 2.552,0.177 10 false : LIN Communication Line 5.729,4.083 6.063,4.292 0.333,0.208 10 false G33 5.74,4.25 6.615,4.49 0.875,0.24 10 false Body ECU 5.708,2.396 5.938,2.573 0.229,0.177 10 false +B 6.292,2.406 6.521,2.583 0.229,0.177 10 false +B 4.698,2.802 4.927,2.979 0.229,0.177 10 false 18 4.313,3.323 4.927,3.51 0.615,0.188 10 false 11*3, 4*4 5,2.792 5.26,2.969 0.26,0.177 10 false L2 5.01,3.344 5.927,3.51 0.917,0.167 10 false UL2*3, UL3*4 2.448,4.281 4.135,4.479 1.688,0.198 10 false *1: for LHD 2.448,4.531 4.135,4.729 1.688,0.198 10 false *2: for RHD 3.458,4.271 5.719,4.49 2.26,0.219 10 false *3: w/o Double Locking System 3.458,4.521 5.719,4.74 2.26,0.219 10 false *4: w/ Double Locking System

CAUTION / NOTICE / HINT

NOTICE:
·

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION



PROCEDURE

1.CHECK DOOR LOCK OPERATION

Result:
Result Proceed to
All doors cannot be locked by power window regulator master switch assembly (w/o Smart Entry and Start System) A
All doors cannot be locked by power window regulator master switch assembly (w/ Smart Entry and Start System) B
All doors cannot be locked by driver door key cylinder C



A

2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B

4.CHECK POWER WINDOW CONTROL SYSTEM

C

7.INSPECT FRONT DOOR LOCK ASSEMBLY
2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Inspect the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY ECU AND BODY GROUND)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY ECU AND BODY GROUND)
a.

Disconnect the K15*1 or J14*2 power window regulator master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G33 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
K15-2 (L) - G33-19 (L1) Always Below 1 Ω
K15-2 (L) or G33-19 (L1) - Body ground Always 10 kΩ or higher
K15-8 (UL) - G33-12 (UL1) Always Below 1 Ω
K15-8 (UL) or G33-12 (UL1) - Body ground Always 10 kΩ or higher
K15-1 (E) - Body ground Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
J14-8 (L) - G33-19 (L1) Always Below 1 Ω
J14-8 (L) or G33-19 (L1) - Body ground Always 10 kΩ or higher
J14-2 (UL) - G33-12 (UL1) Always Below 1 Ω
J14-2 (UL) or G33-12 (UL1) - Body ground Always 10 kΩ or higher
J14-9 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Power window control system operates normally.



Result:
Proceed to
OK
NG



OK

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Replace the power window master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DOOR LOCK OPERATION
6.CHECK DOOR LOCK OPERATION
a.

Check door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Power door lock control system operates normally.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

7.INSPECT FRONT DOOR LOCK ASSEMBLY
a.

Remove the front door lock assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.

Inspect the front door lock assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - BODY ECU AND BODY GROUND)

NG

REPLACE FRONT DOOR LOCK ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - BODY ECU AND BODY GROUND)
a.

Disconnect the K1*1 or J1*2 front door lock assembly LH*1 or RH*2 connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G33 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
K1-9 (L) - G33-18 (L2) Always Below 1 Ω
K1-9 (L) or G33-18 (L2) - Body ground Always 10 kΩ or higher
K1-10 (UL) - G33-11 (UL2) Always Below 1 Ω
K1-10 (UL) or G33-11 (UL2) - Body ground Always 10 kΩ or higher
K1-7 (E) - Body ground Always Below 1 Ω

for RHD, w/o Double Locking System:
Tester Connection Condition Specified Condition
J1-6 (L) - G33-18 (L2) Always Below 1 Ω
J1-6 (L) or G33-18 (L2) - Body ground Always 10 kΩ or higher
J1-5 (UL) - G33-11 (UL2) Always Below 1 Ω
J1-5 (UL) or G33-11 (UL2) - Body ground Always 10 kΩ or higher
J1-8 (E) - Body ground Always Below 1 Ω

for RHD, w/ Double Locking System:
Tester Connection Condition Specified Condition
J1-6 (L) - G33-18 (L2) Always Below 1 Ω
J1-6 (L) or G33-18 (L2) - Body ground Always 10 kΩ or higher
J1-5 (UL) - G33-4 (UL3) Always Below 1 Ω
J1-5 (UL) or G33-4 (UL3) - Body ground Always 10 kΩ or higher
J1-8 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR