Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate the detection of vehicle malfunctions by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A247786
0.75,2.896 1.396,3.177 0.646,0.281 10 false Battery 0.594,2.073 1.052,2.302 0.458,0.229 10 false AM2 1.146,1.198 1.552,1.427 0.406,0.229 10 false G9 1.146,1.323 2.292,1.635 1.146,0.313 10 false Ignition Switch 1.167,0.896 1.594,1.135 0.427,0.24 10 false AM2 1.771,0.896 2.125,1.115 0.354,0.219 10 false IG2 1.021,0.688 1.115,0.844 0.094,0.156 10 false 5 2.094,0.688 2.188,0.844 0.094,0.156 10 false 6 3.948,1.469 5.427,1.75 1.479,0.281 10 false Combination Meter 6.26,1.719 6.688,1.896 0.427,0.177 10 false G88 5.698,0.688 6.01,0.917 0.313,0.229 10 false 30 4.531,0.656 4.927,0.875 0.396,0.219 10 false MIL 2.708,0.938 3.229,1.156 0.521,0.219 10 false MET 5.302,0.688 5.604,0.875 0.302,0.188 10 false 39 3.948,1.333 4.385,1.563 0.438,0.229 10 false G19 3.865,0.927 4.323,1.219 0.458,0.292 10 false IG+ 4.917,0.927 5.354,1.115 0.438,0.188 10 false CHK 3.625,0.698 3.896,0.917 0.271,0.219 10 false 21 6.26,1.865 6.76,2.146 0.5,0.281 10 false ECM 5.938,0.917 6.094,1.052 0.156,0.135 10 false W

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
Result Proceed to
MIL remains on A
MIL does not illuminate B




A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Check if any DTCs have been stored. Note down any DTCs.


f.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

g.

Check if the MIL goes off.

OK:

MIL goes off.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-30 (W) or G19-39 (CHK) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL is illuminated.



Result:
Proceed to
OK
NG



OK

END

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The intelligent tester cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-30 (W) - G19-39 (CHK) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR