Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A240424
4.396,1.125 6.51,1.406 2.115,0.281 10 false 5 V Constant Voltage Circuit 5.354,1.979 6.49,2.427 1.135,0.448 10 false Microprocessor 1.531,1.458 2.781,1.76 1.25,0.302 10 false from MAIN Relay 1.708,1.094 2.771,1.365 1.063,0.271 10 false from EFI Fuse 2.906,1.031 3.427,1.25 0.521,0.219 10 false BATT 0.313,2.135 2.635,2.646 2.323,0.51 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.375,2.979 2.74,3.406 2.365,0.427 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.135 4.333,3.344 0.26,0.208 10 false R 2.99,1.375 3.344,1.573 0.354,0.198 10 false +B 3.167,2.292 3.458,2.521 0.292,0.229 10 false VC 4.885,0.458 5.333,0.688 0.448,0.229 10 false ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A247784
6.125,5.344 6.552,5.573 0.427,0.229 10 false ECM 5.385,0.396 5.635,0.583 0.25,0.188 10 false 18 5.646,0.469 5.979,0.667 0.333,0.198 10 false VC 5.333,0.563 5.75,0.729 0.417,0.167 10 false C75 5.333,0.958 5.708,1.146 0.375,0.188 10 false C75 5.333,1.354 5.677,1.5 0.344,0.146 10 false C75 5.333,1.76 5.688,1.979 0.354,0.219 10 false C75 5.396,0.792 5.635,0.979 0.24,0.188 10 false 20 5.385,1.198 5.573,1.354 0.188,0.156 10 false 19 5.385,1.594 5.688,1.792 0.302,0.198 10 false 28 5.646,0.958 6.156,1.135 0.51,0.177 10 false VTA1 5.646,1.354 6.135,1.552 0.49,0.198 10 false VTA2 5.646,1.677 5.979,1.875 0.333,0.198 10 false E2 5.385,2.667 5.656,2.854 0.271,0.188 10 false 26 5.323,2.823 5.719,3.01 0.396,0.188 10 false G89 5.323,3.229 5.667,3.406 0.344,0.177 10 false G89 5.323,3.625 5.719,3.813 0.396,0.188 10 false G89 5.323,4.052 5.729,4.281 0.406,0.229 10 false G89 5.323,4.448 5.708,4.615 0.385,0.167 10 false G89 5.323,4.854 5.667,5.031 0.344,0.177 10 false G89 5.385,3.073 5.646,3.271 0.26,0.198 10 false 27 5.385,3.469 5.656,3.646 0.271,0.177 10 false 18 5.385,3.896 5.677,4.115 0.292,0.219 10 false 19 5.385,4.292 5.656,4.5 0.271,0.208 10 false 20 5.385,4.688 5.625,4.917 0.24,0.229 10 false 21 5.646,2.719 6.115,2.906 0.469,0.188 10 false VCPA 5.646,3.625 6.094,3.844 0.448,0.219 10 false VPA 5.646,4.365 6.094,4.604 0.448,0.24 10 false EPA 5.646,4.052 6.094,4.219 0.448,0.167 10 false VPA2 5.646,4.76 6.177,4.979 0.531,0.219 10 false EPA2 5.646,3.135 6.167,3.333 0.521,0.198 10 false VCP2 0.219,2.052 0.646,2.271 0.427,0.219 10 false C67 0.219,2.219 1.875,2.448 1.656,0.229 10 false Throttle Position Sensor 2.594,0.552 2.938,0.75 0.344,0.198 10 false VC 2.531,0.948 2.969,1.156 0.438,0.208 10 false VTA 2.448,1.344 2.927,1.552 0.479,0.208 10 false VTA2 2.625,1.75 3.021,1.979 0.396,0.229 10 false E2 2.906,0.469 3.021,0.625 0.115,0.156 10 false 5 2.906,0.865 3.021,1.021 0.115,0.156 10 false 6 2.906,1.271 3.021,1.427 0.115,0.156 10 false 4 2.906,1.667 3.021,1.823 0.115,0.156 10 false 3 0.208,5.156 0.521,5.344 0.313,0.188 10 false G6 0.208,5.313 2.51,5.531 2.302,0.219 10 false Accelerator Pedal Position Sensor 2.396,2.833 2.917,3 0.521,0.167 10 false VCPA 2.406,3.229 2.927,3.438 0.521,0.208 10 false VCP2 2.469,3.635 3.01,3.917 0.542,0.281 10 false VPA 2.406,4.063 2.938,4.25 0.531,0.188 10 false VPA2 2.469,4.458 2.948,4.708 0.479,0.25 10 false EPA 2.396,4.865 2.896,5.094 0.5,0.229 10 false EPA2 2.906,2.74 3.021,2.896 0.115,0.156 10 false 4 2.906,3.146 3.021,3.302 0.115,0.156 10 false 1 2.906,3.542 3.021,3.698 0.115,0.156 10 false 6 2.906,3.979 3.021,4.135 0.115,0.156 10 false 3 2.906,4.385 3.021,4.542 0.115,0.156 10 false 5 2.906,4.771 3.021,4.927 0.115,0.156 10 false 2

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Check the communication between the intelligent tester and ECM.

Result:
Result Proceed to
Communication is possible A
Communication is not possible B




A

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B




A

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

B

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B




A

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

B

5.CHECK HARNESS AND CONNECTOR
5.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor connector.


b.

Disconnect the accelerator pedal position sensor connector.


c.

Disconnect the ECM connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C75-18 (VC) - Body ground Always 10 kΩ or higher
G89-26 (VCPA) - Body ground Always 10 kΩ or higher
G89-27 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR