Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

A flat-type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 6 kHz and 15 kHz.

Knock sensors are fitted onto the engine block to detect engine knocking.

Each knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) Output voltage of the knock sensor (for Bank 1 Sensor 1) is 0.5 V or less (1 trip detection logic).
·

Short in knock sensor circuit

·

Knock sensor

·

ECM


Comes on DTC stored
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) Output voltage of the knock sensor (for Bank 1 Sensor 1) is 4.5 V or higher (1 trip detection logic).
·

Open in knock sensor circuit

·

Knock sensor

·

ECM


Comes on DTC stored

HINT:

When DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

A150243
0.333,0.51 2.083,0.802 1.75,0.292 10 false KNK1 Signal Waveform 2.635,1.927 3.104,2.177 0.469,0.25 10 false GND 2.5,1.063 3.313,1.302 0.813,0.24 10 false 1 V/DIV. 1.031,2.844 2.146,3.073 1.115,0.229 10 false 1 msec./DIV.

Tester Connection Tool Setting Condition Specified Condition
C75-29 (KNK1) - C75-30 (EKNK) 0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown

MONITOR DESCRIPTION

The ECM also senses background engine noise with the knock sensor and uses this noise to check for faults in the sensor. If the knock sensor output voltage is outside the normal range, the ECM interprets this as a fault in the knock sensor and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on.

6.

Start the engine and wait 5 minutes.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0327 or P0328.

11.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

WIRING DIAGRAM

A247767
0.896,1.99 1.031,2.188 0.135,0.198 10 false 1 0.906,0.958 1.104,1.208 0.198,0.25 10 false 2 0.302,2.063 0.688,2.26 0.385,0.198 10 false S1 0.302,2.198 1.458,2.531 1.156,0.333 10 false Knock Sensor 5.688,0.792 5.927,1 0.24,0.208 10 false 29 5.938,0.781 6.5,0.979 0.563,0.198 10 false KNK1 5.688,1.979 5.979,2.198 0.292,0.219 10 false 30 5.948,1.979 6.625,2.219 0.677,0.24 10 false EKNK 6.198,3.333 6.698,3.573 0.5,0.24 10 false ECM 4.625,2.292 4.698,2.427 0.073,0.135 10 false * 0.448,3.292 1.469,3.49 1.021,0.198 10 false *: Shielded 3.25,0.875 3.667,1.063 0.417,0.188 10 false CS1 3.25,2.052 3.719,2.271 0.469,0.219 10 false CS1 6.198,3.177 6.583,3.385 0.385,0.208 10 false C75 3.333,0.688 3.531,0.906 0.198,0.219 10 false 2 3.333,1.875 3.51,2.063 0.177,0.188 10 false 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT KNOCK SENSOR
a.

Disconnect the ECM connector.


b.
A247772
0.583,1.531 1.031,1.792 0.448,0.26 0.917,2.323 0.5,3.021 true 0.969,2.333 1.188,2.667 true 0.083,0.052 0.281,0.25 0.198,0.198 10 false *a 0.688,1.594 0.958,1.75 0.271,0.156 10 false C75 1.115,2.677 1.792,2.833 0.677,0.156 10 false 29 (KNK1) 0.427,3.042 1.135,3.198 0.708,0.156 10 false 30 (EKNK)
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C75-29 (KNK1) - C75-30 (EKNK) 20°C (68°F) 120 to 280 kΩ



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM

NG

3.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
2.INSPECT ECM
a.

Disconnect the CS1 connector.


b.

Turn the ignition switch to ON.


c.
A161605
1.479,0.802 1.896,1.073 0.417,0.271 0.802,2.792 1.469,2.146 true 2.542,2.781 1.927,2.167 true 0.125,0.042 0.333,0.219 0.208,0.177 10 false *a 1.542,0.854 1.865,1.031 0.323,0.177 10 false CS1 1.958,0.813 2.167,0.99 0.208,0.177 10 false *1 0.563,2.833 1.177,3.031 0.615,0.198 10 false EKNK 2.427,2.802 3.042,3 0.615,0.198 10 false KNK1
*1 Female
*a Front view of wire harness connector
(to ECM Wire)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
CS1 female connector 1 - 2 Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the knock sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S1-2 - C75-29 (KNK1) Always Below 1 Ω
S1-1 - C75-30 (EKNK) Always Below 1 Ω
S1-2 or C75-29 (KNK1) - Body ground Always 10 kΩ or higher
S1-1 or C75-30 (EKNK) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR