Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows current to flow to the throttle actuator so that it can be restarted.

HINT:

The ETCS does not use a throttle cable.


A301330
0.177,0.167 4.302,0.531 4.125,0.365 10 Reference (System Diagram): 0.167,0.99 0.917,1.688 0.75,0.698 10 from MAIN Relay 0.094,1.76 1,2.5 0.906,0.74 10 from Battery 1.219,1.99 2.125,2.729 0.906,0.74 10 ETCS 6,0.75 6.833,1.667 0.833,0.917 10 Power Source Circuit for CPU 6,2.344 6.833,3.26 0.833,0.917 10 Throttle Actuator Control Circuit 4.76,0.906 5.417,1.25 0.656,0.344 10 +B 4.75,1.667 5.406,2.01 0.656,0.344 10 +BM 4.75,2.406 5.406,2.75 0.656,0.344 10 M+ 4.75,3.042 5.406,3.385 0.656,0.344 10 M- 4.75,3.729 5.406,4.073 0.656,0.344 10 ME01 5.656,4.208 6.313,4.552 0.656,0.344 10 ECM 0.823,3.552 1.906,3.969 1.083,0.417 10 Throttle Actuator

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2118 Throttle Actuator Control Motor Current Range / Performance Open in the ETCS power source (+BM) circuit (1 trip detection logic).
·

Open in ETCS power source circuit

·

Battery

·

Battery terminals

·

ETCS fuse

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 5 seconds after the engine is next started.

MONITOR STRATEGY

Required Sensors/Components Throttle actuator, Throttle body with motor assembly, ETCS fuse
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Battery voltage 8 V or higher
Electronic throttle actuator power ON

TYPICAL MALFUNCTION THRESHOLDS

Throttle actuator power supply voltage (+BM) Below 4 V

COMPONENT OPERATING RANGE

Throttle actuator power supply voltage (+BM) 11 to 14 V

CONFIRMATION DRIVING PATTERN

A199315
1.042,0.573 1.688,0.781 0.646,0.208 10 false 3000 rpm 1.281,1.958 1.719,2.198 0.438,0.24 10 false Idling 0.49,2.24 1.823,2.542 1.333,0.302 10 false Ignition Switch ON 3.146,2.229 4.813,2.469 1.667,0.24 10 false Approximately 5 seconds 3.469,2.802 4.885,3.063 1.417,0.26 10 false 16 seconds or more 2.01,2.344 2.313,2.583 0.302,0.24 10 false [A] 6,3.24 6.313,3.458 0.313,0.219 10 false [C] 4.604,0.417 4.906,0.646 0.302,0.229 10 false [B]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine.

7.

Slowly depress the accelerator pedal, raise the engine speed to approximately 3000 rpm over approximately 5 seconds, and then idle the engine [B].

8.

Check that 16 seconds or more have elapsed since the engine was started.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2118.

13.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again and, if necessary, drive the vehicle for a period of time.




Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

FAIL-SAFE

When this DTC or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A247779
5.729,4.167 6.25,4.396 0.521,0.229 10 false ECM 5.49,1.302 6.563,1.656 1.073,0.354 10 false Throttle Actuator Control Circuit 4.969,0.406 5.448,0.604 0.479,0.198 10 false +BM 2.521,1.063 2.885,1.323 0.365,0.26 10 false M+ 2.521,1.906 2.802,2.135 0.281,0.229 10 false M- 4.979,1.063 5.365,1.302 0.385,0.24 10 false M+ 4.979,1.906 5.302,2.125 0.323,0.219 10 false M- 4.969,2.625 5.552,3 0.583,0.375 10 false GE01 4.979,3.188 5.448,3.458 0.469,0.271 10 false E1 4.979,3.677 5.5,3.896 0.521,0.219 10 false ME01 4.635,1.167 5.063,1.396 0.427,0.229 10 false C75 4.646,2.01 4.938,2.167 0.292,0.156 10 false C75 4.635,2.635 4.99,2.813 0.354,0.177 10 false C75 4.635,3.188 5.01,3.375 0.375,0.188 10 false C75 4.635,3.688 5.125,4 0.49,0.313 10 false C76 4.635,0.51 5.063,0.792 0.427,0.281 10 false G89 4.74,0.323 4.865,0.479 0.125,0.156 10 false 7 4.729,0.99 4.833,1.146 0.104,0.156 10 false 5 4.729,1.813 4.885,2.01 0.156,0.198 10 false 4 4.729,2.448 4.833,2.604 0.104,0.156 10 false 8 4.729,3 4.865,3.156 0.135,0.156 10 false 3 4.719,3.5 4.823,3.656 0.104,0.156 10 false 3 3.875,2.375 4.573,2.646 0.698,0.271 10 false Shielded 2.802,1.063 3.083,1.354 0.281,0.292 10 false 2 2.802,1.917 3.083,2.156 0.281,0.24 10 false 1 1.833,2.417 2.229,2.635 0.396,0.219 10 false C67 1.844,2.573 3.104,2.906 1.26,0.333 10 false Throttle Actuator 0.979,0.667 1.458,0.885 0.479,0.219 10 false ETCS 0.615,3.771 1.375,4.104 0.76,0.333 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / +BM Voltage.

Powertrain > Engine > Data List
Tester Display
+BM Voltage
50003 61 123

e.

Read the value displayed on the intelligent tester.

Result:
Result Proceed to
Below 11 V or higher than 14 V A
11 to 14 V B




A

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
a.
A247780
2.458,1.01 2.823,1.25 0.365,0.24 2.073,2.833 2.427,2.104 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 2.521,1.052 2.938,1.271 0.417,0.219 10 false G89 2.021,2.854 2.667,3.198 0.646,0.344 10 false 7 (+BM)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G89-7 (+BM) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C75-3 (E1) - Body ground Always Below 1 Ω
C76-3 (ME01) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR