Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY
RM1880E _52 Drivetrain _013221 AXLE AND DIFFERENTIAL _0068544 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 1.ASSEMBLE DIFFERENTIAL CASE

a.
C236671

Install the side gear thrust washer to the side gear.

HINT:

Using the table below, select 2 thrust washers which will ensure that the backlash is within the specifications.


Standard Washer Thickness:
Thickness mm (in.)
0.96 to 1.04 (0.00378 to 0.0409)
1.06 to 1.14 (0.0418 to 0.0448)
1.16 to 1.24 (0.0457 to 0.0488)
1.26 to 1.34 (0.0496 to 0.0527)



b.
C236669

Install the 2 side gears (with thrust washers), 2 pinion gears, 2 pinion gear thrust washers and pinion shaft to the differential case.

HINT:

Align the holes of the differential case and pinion shaft.



c.
C236672

Measure the side gear backlash.

i.

Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


If the backlash is not as specified, install 2 side gear thrust washers with different thicknesses.




d.
C236668

Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the pinion shaft.


e.

Stake the differential case.


Hide 2.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the differential case and ring gear.


b.

Heat the ring gear in boiling water that is approximately 100°C (212°F).


c.

Carefully remove the ring gear from the boiling water.


d.
C236674
0.969,1.323 2.667,1.323 true 0.938,1.5 2.406,1.5 2.406,1.5 2.406,1.333 true 2.719,1.219 3.115,1.573 0.396,0.354 10 false *1
*1 Matchmark


After the moisture on the ring gear has completely evaporated, quickly align the matchmarks on the ring gear and differential case and install the ring gear to the differential case.


e.

Temporarily install 5 new lock plates and the 10 bolts.


f.

After the ring gear cools down, diametrically tighten the 10 bolts uniformly in several passes.

Torque:
97 N*m (989 kgf*cm, 72 ft.*lbf)


g.
C236675
0.406,1.656 0.406,1.281 0.406,1.281 0.271,1.281 false 0.635,2.104 0.271,1.885 0.271,1.885 0.208,1.885 false 1.781,1.771 1.667,1.771 false 2.417,2 2.958,1.917 2.958,1.917 3.146,1.917 false 0.083,1.813 0.208,1.969 0.125,0.156 10 false A 0.125,1.208 0.25,1.365 0.125,0.156 10 false B 1.552,1.698 1.677,1.854 0.125,0.156 10 false B 3.188,1.854 3.427,2.063 0.24,0.208 10 false A

Using a chisel and hammer, stake the 5 lock plates.

HINT:

Strike the tab labeled A so that it is flush with the flat surface of the bolt. Strike the tab labeled B so that half of the tab contacts the bolt as shown in the illustration.



Hide 3.INSTALL REAR DIFFERENTIAL CASE BEARING

a.
C236676
1.542,0.385 0.719,0.385 false 1.385,0.646 0.969,0.646 0.969,0.646 0.969,0.385 false 1.427,1.948 0.552,1.948 false 0.417,0.292 0.875,0.573 0.458,0.281 10 false SST 0.26,1.854 0.688,2.094 0.427,0.24 10 false SST

Using SST and a press, press the 2 case bearings (inner) onto the differential case.

SST
09950-60010  
09950-70010  (09951-00560, 09951-00570, 09951-07150)


Hide 4.INSPECT DIFFERENTIAL RING GEAR RUNOUT

a.

Install the differential case and 2 case bearings (outer) to the carrier, and install the 2 adjusting nuts so that there is no play in the bearing.


b.

Install the 2 bearing caps with the 4 bolts.

Torque:
85 N*m (870 kgf*cm, 63 ft.*lbf)


c.
C237352

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.07 mm (0.00276 in.)


If the runout exceeds the specified maximum value, remove the ring gear and check the runout of the differential case.


d.

Remove the 4 bolts, 2 bearing caps, 2 adjusting nuts and differential case.


Hide 5.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C236677
1.948,0.583 2.427,0.583 false 1.958,0.906 2.24,0.906 2.24,0.906 2.24,0.583 true 2.479,0.49 2.979,0.813 0.5,0.323 10 false SST

Using SST and a press, press the bearing (outer) into the carrier.

SST
09316-60011  (09316-00011, 09316-00021)


Hide 6.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C236678
1.688,0.667 2.198,0.302 2.198,0.302 1.604,1.146 true 2.24,0.167 2.813,0.49 0.573,0.323 10 false SST

Using SST and a press, press the bearing (outer) into the carrier.

SST
09316-60011  (09316-00011, 09316-00041)


Hide 7.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.

Install the plate washer to the drive pinion.

HINT:

First, install a washer that has the same thickness as the removed washer. After checking the tooth contact pattern, replace the washer with one of a different thickness if necessary.



b.
C236679
1.885,1.354 2.344,0.865 2.344,0.865 2.469,0.865 true 2.531,0.781 3.125,1.063 0.594,0.281 10 false SST

Using SST and a press, press the bearing (inner) onto the drive pinion.

SST
09506-30012  


Hide 8.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

a.
C237303

Install the drive pinion, bearing (inner) and oil slinger.

HINT:

Install the spacer and oil seal after adjusting the gear contact pattern.



b.
C237304
1.448,0.698 1.01,0.698 false 0.698,0.594 1.25,0.948 0.552,0.354 10 false SST 2.74,1.24 3.146,1.604 0.406,0.365 10 false *a 0.406,1.604 0.76,1.906 0.354,0.302 10 false *b
*a Turn
*b Hold


Using SST, install the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



c.
C237305
1.76,0.625 1.76,0.125 1.76,0.125 1.927,0.125 false 1.99,0.031 2.563,0.313 0.573,0.281 10 false SST

Adjust the drive pinion preload by installing the drive pinion nut.


d.

Using SST to hold the companion flange in place, tighten the nut.

SST
09330-00021  (09330-00030)

Torque:
230 N*m (2345 kgf*cm, 170 ft.*lbf)

or less


NOTICE:
·

As there is no spacer, tighten a little at a time. Be careful not to overtighten the nut.

·

Apply hypoid gear oil LSD to drive pinion thread and nut seat face.




e.
C237317

Using a torque wrench, measure the preload.

Standard Drive Pinion Preload (Starting Torque):
Bearing Specified Condition
New bearing 1.4 to 2.0 N*m (15 to 20 kgf*cm, 13 to 17 in.*lbf)
Reused bearing 0.6 to 0.9 N*m (7 to 9 kgf*cm, 6 to 7 in.*lbf)


NOTICE:
·

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.

·

Record the differential drive pinion preload for the total preload measurement.




Hide 9.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C236658

Install the differential case and 2 case bearings (outer) to the differential carrier.

HINT:

Make sure the 2 case bearings (outer) are not interchanged.



Hide 10.INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT

a.
C237306

Install the 2 adjusting nuts to the carrier, making sure the nuts are threaded properly.


Hide 11.INSPECT AND ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

a.
C236657
1.656,1.281 0.313,1.281 true 1.646,1.229 1,1.229 1,1.229 1,1.271 true 1.229,0.896 0.833,0.896 0.833,0.896 0.833,1.271 true 1.229,0.854 0.563,0.854 0.563,0.854 0.563,1.271 true 0.156,1.198 0.479,1.521 0.323,0.323 10 false *1
*1 Matchmark


Align the matchmarks on the caps and carrier.


b.
C237308

Install the right and left bearing caps with the 4 bolts.

Torque:
85 N*m (870 kgf*cm, 63 ft.*lbf)

If the bearing cap does not fit tightly on the carrier, the adjusting nuts are not threaded properly.

HINT:

Reinstall the adjusting nuts if necessary.




c.
C237309
1.604,1.385 1.604,2.021 1.604,2.021 1.802,2.021 true 1.542,3.625 1.24,4.115 1.24,4.115 1.24,4.333 true 0.104,0.052 0.469,0.406 0.365,0.354 10 false *a 0.135,2.354 0.563,2.656 0.427,0.302 10 false *b 1.885,1.927 2.427,2.302 0.542,0.375 10 false SST 1.125,4.365 1.573,4.646 0.448,0.281 10 false SST
*a for LH Side
*b for RH Side


Loosen the 4 bearing cap bolts to the point where the adjusting nuts can be turned by SST.


d.

Using SST, tighten the adjusting nut on the ring gear side until the ring gear has a backlash of about 0.2 mm (0.00787 in.).

SST
09504-00011  
09960-10010  (09962-01000, 09963-00700)


e.

While turning the ring gear, use SST to fully tighten the adjusting nut on the drive pinion side. After the bearings have settled, loosen the adjusting nut on the drive pinion side.

SST
09504-00011  
09960-10010  (09962-01000, 09963-00700)


f.

Using SST, tighten the adjusting nut 1 to 1.5 notches from the 0 preload position.


g.
C237310
1.583,1.604 1.583,1.969 1.583,1.969 1.99,1.969 true 2.042,1.875 2.583,2.094 0.542,0.219 10 false SST

Using a dial indicator, adjust the ring gear backlash until it is within the specification.

Standard backlash:

0.13 to 0.18 mm (0.00512 to 0.00708 in.)


HINT:
·

The backlash is adjusted by turning the left and right adjusting nuts by an equal amount. For example, loosen the nut on the right side one notch and loosen the nut on the left side one notch.

·

Perform the measurement at 3 or more positions around the circumference of the ring gear.




h.
C236657

Tighten the bearing cap bolts.

Torque:
85 N*m (870 kgf*cm, 63 ft.*lbf)


Hide 12.INSPECT TOTAL PRELOAD

a.
C236639

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Total Preload:
Bearing Specified Condition
New Bearing 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload
Reused Bearing 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload


If the result is not as specified, adjust the preload.

NOTICE:

Record the differential ring gear preload.



Hide 13.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.
C237311

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


b.

Hold the companion flange firmly in place and rotate the ring gear in both directions.


c.

Inspect the tooth contact pattern.

C267774
0.51,0.99 1.01,1.354 0.5,0.365 10 *a 2.854,0.604 3.333,0.938 0.479,0.333 10 *b 6.375,0.635 6.938,1.094 0.563,0.458 10 *c 2.865,2.427 3.458,2.771 0.594,0.344 10 *d 6.396,2.438 7.031,2.896 0.635,0.458 10 *e 4.729,1.583 5.229,1.958 0.5,0.375 10 *f 4.688,3.333 5.198,3.771 0.51,0.438 10 *g
*a Proper Contact *b Heel Contact
*c Face Contact *d Toe Contact
*e Flank Contact *f Select an adjusting washer that brings the drive pinion closer to the ring gear
*g Select an adjusting washer that shifts the drive pinion away from the ring gear - -


C237312
1.74,1.448 1.74,1.844 1.74,1.844 2.083,1.844 false 2.135,1.74 2.479,2.042 0.344,0.302 10 false *1
*1 Plate Washer


If the teeth are not contacting properly, use the following chart to select a proper washer.

Standard Plate Washer Thickness:
Thickness mm (in.) Thickness mm (in.)
2.23 to 2.25 (0.0878 to 0.0885) 2.50 to 2.52 (0.0985 to 0.0992)
2.26 to 2.28 (0.0890 to 0.0897) 2.53 to 2.55 (0.0996 to 0.1003)
2.29 to 2.31 (0.0902 to 0.0909) 2.56 to 2.58 (0.1008 to 0.1015)
2.32 to 2.34 (0.0914 to 0.0921) 2.59 to 2.61 (0.1020 to 0.1027)
2.35 to 2.37 (0.0926 to 0.0933) 2.62 to 2.64 (0.1032 to 0.1039)
2.38 to 2.40 (0.0937 to 0.0944) 2.65 to 2.67 (0.1044 to 0.1051)
2.41 to 2.43 (0.0949 to 0.0956) 2.68 to 2.70 (0.1056 to 0.1062)
2.44 to 2.46 (0.0961 to 0.0968) 2.71 to 2.73 (0.1070 to 0.1074)
2.47 to 2.49 (0.0973 to 0.0980) -




Hide 15.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 16.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 17.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 18.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 19.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C237314

Install the bearing (inner) to the drive pinion.


Hide 20.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 22.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 23.INSPECT TOTAL PRELOAD

a.
C237317

Using a torque wrench, measure the preload.

Standard Total Preload:
Bearing Specified Condition
New bearing 1.5 to 2.1 N*m (15 to 21 kgf*cm, 14 to 19 in.*lbf) + ring gear preload
Reused bearing 0.7 to 1.0 N*m (7 to 10 kgf*cm, 6 to 9 in.*lbf) + ring gear preload


If necessary, disassemble and inspect the differential.



Hide 24.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C236650

Using a dial indicator, check the backlash of the ring gear.

Standard backlash:

0.13 to 0.18 mm (0.00511 to 0.00709 in.)


If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 25.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 27.INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C237318

Install 2 new adjusting nut locks to the bearing caps with the 2 bolts.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


b.

Bend the nut locks.