Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER
RM1880E _53 Suspension _013223 FRONT SUSPENSION _0068547 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT COIL SPRING LH

a.
C159782
0.115,0.613 0.414,0.758 0.3,0.145 10 SST 0.464,0.688 0.688,0.688 false 0.688,0.688 0.727,0.793 false

Secure SST in a vise.

SST
09727-30022  (09727-00010, 09727-00021, 09727-00031)


b.
C275706
0.208,0.135 0.521,0.292 0.313,0.156 10 false *a 0.271,2.542 0.583,2.698 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Attach the arm of SST to the diameter of the coilspring.

CAUTION:
·

Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




c.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench.




d.
C281512
2.656,1.167 2.656,0.667 true 1.854,1.917 2.01,1.729 2.01,1.729 2.313,1.729 false 2.604,1.208 2.917,1.365 0.313,0.156 10 false *a 2.406,1.656 2.906,1.813 0.5,0.156 10 false SST
*a Recess


Install the coil spring to the shock absorber. Fit the lower end of the coil spring into the recess of the spring lower seat.


Hide 2.INSTALL FRONT COIL SPRING UPPER INSULATOR LH

a.

Install the upper insulator to the shock absorber.


Hide 3.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH

a.

Install the cushion retainer to the shock absorber.


b.

Install the suspension support to the shock absorber.


Hide 4.INSTALL FRONT SHOCK ABSORBER CUSHION

a.

Install the cushion to the shock absorber.


Hide 5.INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER

a.

Install the cushion retainer to the shock absorber.


Hide 6.INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C113158
0.885,1.427 0.885,1.698 false 2.344,1.063 2.344,1.677 true 0.25,0.125 0.479,0.365 0.229,0.24 10 false *a 2.927,0.094 3.156,0.333 0.229,0.24 10 false *c 1.604,0.083 1.833,0.323 0.229,0.24 10 false *b 0.833,1.729 1.063,1.969 0.229,0.24 10 false *1 2.292,1.719 2.531,1.958 0.24,0.24 10 false *2
*1 Suspension Support
*2 Absorber Bush
*a for LH
*b Front
*c for RH


Align the suspension support and absorber bushes as shown in the illustration.


b.

Install a new lock nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Do not use an impact wrench. It will damage the shock absorber rod.



c.

Release the coil spring while checking the position of the spring lower seat and suspension support.


Hide 7.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

F049915

a.

Install the shock absorber to the vehicle body so that: 1) the coil spring LH lower tip is facing away from the vehicle, and 2) the coil spring RH lower tip is facing toward the vehicle.


b.
C288511
0.75,0.198 1.125,0.198 1.125,0.198 1.417,0.427 true 0.531,3.667 0.854,3.667 0.854,3.667 1.052,4.146 false 2.01,2.323 2.323,2.479 0.313,0.156 10 false *a 0.427,0.115 0.833,0.323 0.406,0.208 10 true SST 0.219,3.594 0.677,3.792 0.458,0.198 10 false SST
*a Fulcrum Length


Using SST and 150 mm extension bar, install the 3 nuts to the upper side of the shock absorber with coil spring.

SST
09249-B1010  

Torque:
without SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)
with SST : 28 N*m (286 kgf*cm, 21 ft.*lbf)

HINT:

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).



c.
F049906

Temporarily install the bolt and nut as shown in the illustration.

HINT:

Fix the nut in place and temporarily install the bolt.



Hide 10.INSTALL FRONT STABILIZE LINK ASSEMBLY LH

a.

Connect the stabilizer link to the lower arm with the nut.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 11.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 12.INSTALL FRONT WHEEL

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

Hide 13.STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Press down on the vehicle several times to stabilize the suspension.


Hide 14.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Fix the nut in place and tighten the bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 15.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT