Home › Suspension › FRONT SUSPENSION › FRONT UPPER SUSPENSION ARM
RM1880E _53 Suspension _013223 FRONT SUSPENSION _0068548 FRONT UPPER SUSPENSION ARM A

FRONT SUSPENSION  FRONT UPPER SUSPENSION ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT UPPER BALL JOINT

a.
C237853
0.844,0.938 1.521,0.542 1.521,0.542 1.823,0.542 true 0.521,1.875 0.719,2.292 0.719,2.292 0.896,2.292 false 1.885,0.458 2.281,0.677 0.396,0.219 10 false SST 0.958,2.198 1.354,2.417 0.396,0.219 10 false SST

Using SST and a press, press in a new upper ball joint.

SST
09612-30012  
09223-00010  


b.

Using a snap ring expander, install a new snap ring.

NOTICE:

Make sure the snap ring is securely installed in the groove.



Hide 2.INSTALL UPPER BALL JOINT DUST COVER

a.
C159213
1.906,1.25 2,1.25 false 1.427,1.25 1.521,1.25 false 2.521,1.656 2.521,0.938 2.521,0.938 2.063,0.938 true 2.51,1.417 2.094,1.417 2.094,1.417 1.948,1.25 false 1.427,1.25 0.979,1.25 false 0.781,1.146 1.146,1.469 0.365,0.323 10 false *1 2.479,1.719 2.75,1.969 0.271,0.25 10 false *1
*1 MP Grease No. 2


Pack the upper ball joint with MP grease No. 2.

Grease capacity:

8.0 g (0.282 oz.)



b.

Apply MP grease No. 2 to the locations shown in the illustration.

NOTICE:

Do not apply MP grease No. 2 to the tapered or threaded parts of the ball joint.



c.

Install a new dust cover to the upper arm.


d.

Install a new dust cover set ring.


Hide 3.INSTALL FRONT UPPER SUSPENSION ARM BUSH

a.
F049921
0.396,0.385 0.688,0.385 0.688,0.385 0.865,0.563 false 0.094,0.292 0.51,0.552 0.417,0.26 10 false SST

Using SST and a press, press in a new upper arm bush.

SST
09710-22021  (09710-01031)


Hide 4.TEMPORARILY INSTALL FRONT UPPER SUSPENSION ARM ASSEMBLY LH

F049917

a.

Temporarily install the upper arm with the 2 bolts and 2 nuts.

HINT:

Fix the nuts in place and temporarily install the bolts.



b.

Install the upper arm to the front axle with the nut.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


c.

Install a new clip.


Hide 5.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 8.TIGHTEN FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.

Tighten the 2 bolts of the upper arm.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


Hide 9.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT