Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM
RM1880E _53 Suspension _013223 FRONT SUSPENSION _0068549 FRONT LOWER SUSPENSION ARM A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL LOWER BALL JOINT ASSEMBLY

a.
C237856
1.75,0.198 2.104,0.198 2.104,0.198 2.635,0.854 true 2.458,2.302 2.667,2.302 2.667,2.302 2.906,1.938 false 1.448,0.094 1.854,0.302 0.406,0.208 10 false SST 2.146,2.198 2.552,2.406 0.406,0.208 10 false SST

Using SST and press, press in a new lower ball joint.

SST
09226-10010  
09631-32020  


b.

Install a new snap ring.

NOTICE:

Make sure the snap ring is securely installed in the groove.



c.
C237891
1.615,0.75 1.76,0.75 false 2.115,0.75 2.25,0.75 false 1.646,0.771 1.76,0.771 false 2.115,0.771 2.229,0.771 false 0.844,0.583 1.385,0.583 1.385,0.583 1.667,0.76 true 1.125,0.594 1.125,1.115 1.125,1.115 1.583,1.115 true 0.656,0.469 1,0.729 0.344,0.26 10 false *1
*1 MP Grease No. 2


Pack the upper ball joint with MP grease No. 2.

Grease capacity:

8.0 g (0.282 oz.)



d.

Apply MP grease No. 2 to the locations shown in the illustration.

NOTICE:

Do not apply MP grease No. 2 to the tapered or threaded parts of the ball joint.



e.

Install a new dust cover to the lower arm.


f.

Install a new dust cover set ring.


Hide 2.INSTALL FRONT NO. 2 LOWER ARM BUSH

a.
C281517
0.51,3.375 1.156,3.021 1.156,3.021 0.521,3.854 true 0.688,1.385 0.51,1.385 false 0.635,0.74 0.458,0.74 false 1.208,2.885 1.521,3.156 0.313,0.271 10 false *a 0.188,1.281 0.792,1.479 0.604,0.198 10 false SST 0.156,0.635 0.76,0.833 0.604,0.198 10 false SST
*a Bush Positioning Protrusion


Using SST and a press, install a new bush.

SST
09710-20011  (09710-03081)
09726-27012  (09726-02041)

NOTICE:

Press the bush while making sure the bush positioning protrusions are perpendicular to the lower arm as shown in the illustration.



Hide 3.INSTALL FRONT NO. 1 LOWER ARM BUSH

a.
C281518
0.875,1.417 0.552,1.021 0.552,1.021 0.865,1.188 false 0.24,0.906 0.698,1.104 0.458,0.198 10 false SST

Using SST and a press, press in a new bush.

SST
09710-20011  (09710-06071)
09710-22021  (09710-01071)


Hide 4.INSTALL FRONT LOWER BALL JOINT ATTACHMENT LH

a.

Install the ball joint attachment with the nut and a new cotter pin.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 5.TEMPORARILY INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

F049925
0.969,0.635 1.76,0.365 1.76,0.365 2.646,0.792 true 1.698,0.125 1.927,0.333 0.229,0.208 10 true *1
*1 Matchmark


a.

Temporarily install the lower arm, and No. 1 and No. 2 camber adjusting cams with the 2 camber adjusting cams and 2 nuts.


b.

Align the matchmarks on the No. 1 camber adjusting cam and No. 2 camber adjusting cam with the corresponding matchmarks on the vehicle frame.


c.
F049924

Install the ball joint attachment with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 6.INSTALL FRONT SPRING BUMPER

a.
C237887
2.5,1.729 2.344,1.729 2.344,1.729 2.115,1.417 false 2.563,1.625 3.094,1.875 0.531,0.25 10 false SST

Using SST, install the front spring bumper to the lower arm.

SST
09922-10010  

Torque:
for use without SST : 31 N*m (316 kgf*cm, 23 ft.*lbf)
for use with SST : 23 N*m (231 kgf*cm, 17 ft.*lbf)

HINT:
·

Rotate SST in the direction shown in the illustration.

·

Use a torque wrench with a fulcrum length of 345 mm (13.6 in.).




Hide 7.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Temporarily install the shock absorber with coil spring with the bolt and nut.


Hide 8.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the stabilizer link to the lower arm with the nut.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 12.TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

a.

Tighten the 2 nuts.

Torque:
210 N*m (2141 kgf*cm, 155 ft.*lbf)


Hide 13.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Fix the nut in place and tighten the bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 14.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT