Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM1880E _54 Brake _013226 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0068558 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

When one of the following conditions is met, the brake warning light remains on:

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

The PKB terminal circuit is shorted.


WIRING DIAGRAM

C241552
5.333,5.385 5.635,5.563 0.302,0.177 10 false A13 5.333,5.594 6.979,5.969 1.646,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 2.313,1.448 2.667,1.615 0.354,0.167 10 false G19 2.323,1.615 4.344,1.781 2.021,0.167 10 false Combination Meter Assembly 3.5,0.844 3.927,1.021 0.427,0.177 10 false Brake 4.531,0.542 4.74,0.708 0.208,0.167 10 false 36 2.052,0.531 2.24,0.708 0.188,0.177 10 false 21 0.49,0.615 1.458,0.813 0.969,0.198 10 false from IG Circuit 1.146,2.635 1.51,2.844 0.365,0.208 10 false A18 1.146,2.823 4.125,3.292 2.979,0.469 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly) 2.479,2.354 2.667,2.552 0.188,0.198 10 false 1 1.313,2.365 1.5,2.563 0.188,0.198 10 false 2 1.156,4.135 1.469,4.313 0.313,0.177 10 false K6 1.167,4.292 3.188,4.5 2.021,0.208 10 false Parking Brake Switch Assembly 2.49,3.781 2.677,3.979 0.188,0.198 10 false 1 5.76,3.865 6.167,4.063 0.406,0.198 10 false PKB 5.458,3.802 5.667,4.01 0.208,0.208 10 false 18 4.167,0.542 4.438,0.708 0.271,0.167 10 false SW 2.323,0.542 2.594,0.698 0.271,0.156 10 false IG+

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.

Turn the ignition switch to ON.


b.

With the brake fluid at the specified level, disconnect the brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off B


HINT:

If the brake warning light turns off, the brake fluid level warning switch (brake master cylinder reservoir sub-assembly) has an internal short circuit.




A

2.INSPECT PARKING BRAKE SWITCH ASSEMBLY

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Remove the parking brake switch.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL


c.

Inspect the parking brake switch.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BRAKE WARNING LIGHT CIRCUIT)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BRAKE WARNING LIGHT CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G19 combination meter connector.


d.

Disconnect the parking brake switch connector.


e.

Disconnect the brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-18 (PKB) - G19-36 (SW) Always Below 1 Ω
A13-18 (PKB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SKID CONTROL ECU (PKB INTERNAL CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SKID CONTROL ECU (PKB INTERNAL CIRCUIT)
a.

Turn the ignition switch off.


b.

Release the parking brake.


c.

Start the engine.


d.

Disconnect the skid control ECU (brake actuator assembly) connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off B


HINT:

If the brake warning light turns off, the skid control ECU (brake actuator assembly) has an internal short circuit.




A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B