Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM1880E _54 Brake _013228 BRAKE (FRONT) _0068569 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT DISC

a.
C111369
1.677,1.115 0.906,0.344 0.906,0.344 0.771,0.344 true 1.677,1.24 0.906,0.344 true 0.604,0.271 0.75,0.406 0.146,0.135 10 false *1
*1 Matchmark


Align the matchmarks and install the disc.

HINT:

When replacing the disc with a new one, select the installation position where the disc has the minimum runout.



Hide 2.INSTALL FRONT DISC BRAKE BUSH DUST BOOT

a.
C122649
0.49,2.927 0.854,3.219 0.365,0.292 10 false *1
*1 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to 2 new boots.


b.

Install the 2 boots to the mounting.


Hide 3.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C239762
2.271,0.708 2.271,0.354 2.271,0.354 1.875,0.354 false 2.198,2.042 2.198,2.552 2.198,2.552 2.365,2.552 false 0.823,2.156 0.823,1.844 0.823,1.844 0.552,1.844 false 1.698,0.281 2,0.563 0.302,0.281 10 false *1 2.385,2.479 2.708,2.74 0.323,0.26 10 false *2 0.365,1.76 0.656,2.042 0.292,0.281 10 false *3 0.688,2.917 1.177,3.167 0.49,0.25 10 false *4
*1 Cylinder Slide Pin (Upper)
*2 Cylinder Slide Pin (Lower)
*3 Cylinder Slide Bush
*4 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the pins and a new bush as shown in the illustration.


b.

Install the bush to the pin (lower).


c.

Install the 2 pins (upper and lower) to the mounting.


Hide 4.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH

a.

Install the cylinder mounting with the 2 bolts.

Torque:
117 N*m (1191 kgf*cm, 86 ft.*lbf)


Hide 5.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the 2 plates to the mounting.


Hide 6.INSTALL FRONT ANTI SQUEAL SHIM KIT

a.
C177135
2.344,0.865 2.344,0.354 2.344,0.354 1.49,0.354 false 0.938,2.354 0.938,2.781 0.938,2.781 1.896,2.781 false 1.313,0.25 1.646,0.51 0.333,0.26 10 false *1 1.927,2.708 2.271,2.958 0.344,0.25 10 false *2
*1 No. 1 Anti-squeal Shim
*2 No. 2 Anti-squeal Shim


Install the No. 1 and No. 2 anti-squeal shims to each pad as shown in the illustration.

NOTICE:

There should be no oil or grease on the friction surface of the pads and disc.



Hide 7.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 disc brake pads to the mounting.

NOTICE:

There should be no oil grease on the friction surface of the pads and disc.



Hide 8.INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

a.
C242453
0.667,4.229 1.063,4.521 0.396,0.292 10 false *1 1,2.354 1.344,2.646 0.344,0.292 10 false *a
*1 Silicon grease
*a Inner Side


Apply silicon grease on contact surface of each fingers.


b.

Install the cylinder with the 2 bolts.

Torque:
29 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 9.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the flexible hose with a new gasket and the new union bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Install the flexible hose lock securely in the lock hole in the cylinder.



Hide 11.BLEED AIR FROM CLUTCH LINE (for Manual Transmission)