Home › Audio / Visual / Telematics › AUDIO / VIDEO › FRONT DOOR SPEAKER
RM1880E _56 Audio / Visual / Telematics _013234 AUDIO / VIDEO _0068585 FRONT DOOR SPEAKER A

AUDIO / VIDEO  FRONT DOOR SPEAKER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

a.

Install a nose piece to an air riveter or hand riveter. Then insert the mandrel part of a new φ4 mm waterproof rivet into the nose piece.


b.
E226354

Using an air riveter or hand riveter, install the front No. 1 speaker assembly with 3 new rivets.

NOTICE:
·
B171664
1.229,1.104 1.083,1.635 1.083,1.635 1.24,2.198 false 1.083,1.635 0.813,1.635 false 1.792,0.896 2.031,1.635 2.031,1.635 1.75,2.521 true 2.031,1.635 2.313,1.635 false 2.26,0.604 2.563,0.813 0.302,0.208 10 false *a 2.26,2.448 2.583,2.688 0.323,0.24 10 false *b 2.365,1.531 2.677,1.729 0.313,0.198 10 false *1 0.573,1.552 0.844,1.74 0.271,0.188 10 false *2
*1 Mandrel
*2 Riveter
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B172390
0.719,0.104 1.021,0.104 false 0.802,1.146 1,1.146 false 0.802,2.438 1,2.438 false 2.313,0.563 2.646,0.792 0.333,0.229 10 false *a 2.313,2.76 2.625,2.99 0.313,0.229 10 false *b 1.052,2.365 1.354,2.635 0.302,0.271 10 false *1 2.313,1.573 2.625,1.823 0.313,0.25 10 false *a 1.052,1.073 1.333,1.26 0.281,0.188 10 false *1 1.052,0.031 1.365,0.24 0.313,0.208 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the speaker.

·

Do not tilt the riveter when installing the rivet to the speaker.

·

Do not leave any space between the rivet head and speaker.

·
B172391
0.729,0.646 0.927,0.646 false 0.719,2.156 0.927,2.156 false 2.292,1.042 2.615,1.281 0.323,0.24 10 false *a 2.292,2.469 2.635,2.688 0.344,0.219 10 false *b 0.979,0.563 1.292,0.792 0.313,0.229 10 false *1 0.979,2.073 1.271,2.281 0.292,0.208 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the speaker and door. Firmly hold together the 2 items while installing the rivet.




c.

Connect the connector.


Hide 2.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 3.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

Hide 4.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

a.

Install the front No. 2 speaker assembly with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the connector.


Hide 5.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).