Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM1880E _59 Vehicle Exterior _013249 DOOR / HATCH _0068714 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door check.


b.

When reusing a bolt labeled B:

i.

Clean the threads of the bolt labeled B with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt labeled B.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B291441
2.052,1.167 1.938,1.167 1.938,1.167 1.938,1.271 true 1.948,0.521 1.948,0.313 1.948,0.313 2.354,0.313 true 1.427,1.74 1.198,1.74 false 2.438,0.198 2.729,0.417 0.292,0.219 10 false *1 2.063,1.052 2.26,1.271 0.198,0.219 10 true *1 0.958,1.646 1.177,1.833 0.219,0.188 10 true *2
*1 Bolt A
*2 Bolt B


Install the front door check with the 2 bolts labeled A and bolt labeled B.

Torque:
Bolt A : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Bolt B : 21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 2.INSTALL FRONT DOOR OUTSIDE MOULDING LH (w/ Outside Moulding)

Hide 3.INSTALL FRONT DOOR WEATHERSTRIP LH

HINT:

When installing the front door weatherstrip, heat the front door panel using a heat light.


Standard:
Item Temperature
Front Door Panel 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the front door panel excessively.


a.

Clean the front door panel surface.

i.

Using a heat light, heat the front door panel surface.


ii.

Remove the double-sided tape from the front door panel surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B291515
0.646,0.146 0.865,0.313 0.219,0.167 10 false A 0.219,0.417 0.458,0.594 0.24,0.177 10 false B 1.031,0.677 1.229,0.844 0.198,0.167 10 false C 2.396,0.146 2.625,0.344 0.229,0.198 10 false A 1.969,0.417 2.208,0.604 0.24,0.188 10 false B 2.552,0.75 2.781,0.938 0.229,0.188 10 false C

When reusing a front door weatherstrip:

i.

Remove the double-sided tape from the front door weatherstrip surface.


ii.

Wipe off any tape adhesive residue with cleaner.


iii.

While using the position shown in the illustration as a reference, apply the double-sided tape to the front door weatherstrip.

Standard:
Area Measurement
A 50 mm (1.97 in.)
B 7 mm (0.276 in.)
C 0.8 mm (0.0315 in.)




c.

Install the front door weatherstrip.

i.

Attach the 17 clips to install the front door weatherstrip.


ii.

Remove the peeling paper from the face of the front door weatherstrip and apply the double-sided tape to the front door panel.

HINT:
·

After removing the peeling paper, keep the exposed adhesive free from foreign matter.

·

Press the front door weatherstrip firmly to install it.





Hide 4.INSTALL FRONT DOOR PANEL CUSHION

a.

Install a new front door panel cushion.


Hide 5.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the front door rear outside handle pad.


Hide 6.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the front door front outside handle pad.


Hide 7.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.

Install the front door lock open rod to the front door outside handle frame.


b.
B291509
1.865,0.271 1.604,0.438 false 1.917,0.135 2.146,0.323 0.229,0.188 10 false *1
*1 Snap


Rotate the snap in the direction indicated by the arrow in the illustration to attach the snap to the front door lock open rod.


Hide 8.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door outside handle frame.


b.

Attach the claw to install the front door outside handle frame.


c.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 9.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B291510

Install the front door outside handle by moving it in the direction indicated by the arrow shown in the illustration.


Hide 10.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the front door inside locking cable.


b.

Attach the 3 claws to close the cover.


Hide 11.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the front door lock remote control cable.


Hide 12.INSTALL FRONT DOOR LOCK ASSEMBLY LH

Hide 13.INSTALL FRONT DOOR OUTSIDE HANDLE COVER

a.

Attach the 2 claws to install the front door outside handle cover to the door key cylinder.


b.

Using a T30 "TORX" socket wrench, install the front door outside handle cover together with the door key cylinder with the screw.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.

Install the hole plug.


Hide 14.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.

Install the front door rear lower frame with the 2 nuts.


Hide 15.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B276850

Apply MP grease to the sliding and rotating areas of the front door window regulator.


b.

Temporarily install the temporary bolt to the front door window regulator.


c.
B291427
1.688,0.156 1.76,0.156 1.76,0.156 1.99,0.479 true 1.5,0.052 1.76,0.281 0.26,0.229 10 false *1
*1 Temporary Bolt


Install the front door window regulator with the 5 bolts, and then tighten the temporary bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to drop the front door window regulator as it may become damaged.



d.

Connect the connector.


Hide 19.INSTALL FRONT DOOR GLASS RUN LH

a.

Install the front door glass run.


Hide 21.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Temporarily install the power window regulator master switch assembly with front door armrest base panel.


b.

Connect the cable to the negative (-) battery terminal.


c.

Operate the front door window regulator so that the front door glass can be installed.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



e.

Remove the power window regulator master switch assembly with front door armrest base panel.


f.
B291512
2.125,0.063 2.427,0.271 0.302,0.208 10 false (1) 0.781,0.323 1.073,0.521 0.292,0.198 10 true (2)

Insert the front door glass into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.


g.

Install the front door glass with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 22.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the front door panel.


b.

Pass the wire harness through a new front door service hole cover.


c.
B291513
0.531,0.521 0.75,0.719 true 2.917,0.604 2.708,0.781 true 0.344,0.396 0.573,0.604 0.229,0.208 10 true *a 2.969,0.469 3.24,0.667 0.271,0.198 10 false *a
*a Reference Point


Pass the front door inside locking cable and front door lock remote control cable through a new front door service hole cover, and then install the front door service hole cover using the reference points on the front door panel.


Hide 23.INSTALL FRONT DOOR NO. 1 TRIM BRACKET

a.

Install the front door No. 1 trim bracket with the 2 screws.


Hide 24.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.

Connect the front door inside locking cable and front door lock remote control cable to the front door inside handle.


b.
B291514

Attach the 2 guides as indicated by the arrow in the illustration, and then attach the claw to install the front door inside handle.


Hide 25.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 27.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)

Hide 28.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B291516

Install the front door inner glass weatherstrip to the front door trim board and fold down the 7 claws in the directions indicated by the arrows in the illustration.


Hide 29.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.

Attach the 9 clips to install the front door trim board.


Hide 30.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.

Attach the 3 clips to install the front door lower frame bracket garnish.


Hide 31.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

a.

Connect the connector.


b.

Attach the 8 claws and 2 clips to install the power window regulator master switch assembly with front door armrest base panel.


c.

Install the screw.


Hide 32.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 33.INITIALIZE POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)