Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM1880E _56 Audio / Visual / Telematics _013234 AUDIO / VIDEO _0068593 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM

C240222
0.823,3.49 1.385,3.729 0.563,0.24 10 false LH Side 0.823,5.01 1.365,5.25 0.542,0.24 10 false RH Side 5.781,4.531 5.979,4.719 0.198,0.188 10 false 7 5.75,3.01 5.958,3.208 0.208,0.198 10 false 23 5.75,1.49 5.948,1.688 0.198,0.198 10 false 10 4.865,3.125 5.063,3.333 0.198,0.208 10 false 4 4,3.115 4.198,3.313 0.198,0.198 10 false 8 4.844,1.604 5.063,1.823 0.219,0.219 10 false 12 5.729,1.688 5.99,1.896 0.26,0.208 10 false G5 5.74,3.208 6.031,3.438 0.292,0.229 10 false G1 5.729,4.729 6.042,4.938 0.313,0.208 10 false G5 1.354,5.802 1.615,6.021 0.26,0.219 10 false z3 4.031,5.802 4.385,6.042 0.354,0.24 10 false G12 1.104,4.281 1.479,4.51 0.375,0.229 10 false DISP 1.104,2.865 1.594,3.115 0.49,0.25 10 false MODE 6.052,4.729 6.385,4.99 0.333,0.26 10 false GND 6.042,3.219 6.51,3.417 0.469,0.198 10 false SWG 6.052,1.719 6.406,1.958 0.354,0.24 10 false ILL+ 4.333,3.115 4.708,3.365 0.375,0.25 10 false EAU 4.333,1.583 4.698,1.833 0.365,0.25 10 false IL+2 1.115,2.375 1.542,2.604 0.427,0.229 10 false Seek 1.208,1.875 1.51,2.115 0.302,0.24 10 false Vol 3.99,1.594 4.198,1.802 0.208,0.208 10 false 5 6.021,5.979 6.979,6.427 0.958,0.448 10 false Radio Receiver Assembly 4.031,5.979 4.99,6.448 0.958,0.469 10 false Spiral Cable Sub-assembly 1.354,5.979 3.292,6.26 1.938,0.281 10 false Steering Pad Switch Assembly 0.521,0.427 1.979,0.865 1.458,0.438 10 false from Headlight Dimmer Switch Assembly

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio receiver assembly, steering pad switch assembly, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio receiver assembly. B
No illumination comes on (radio receiver assembly, hazard switch, glove box, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY)

B

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BATTERY AND BODY GROUND)

C

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY)
a.

Disconnect the G12 spiral cable sub-assembly connector.


b.
E198671
1.438,0.5 1.875,0.75 0.438,0.25 2.042,1.635 2.5,1.74 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.521,0.552 1.906,0.771 0.385,0.219 10 false G12 2.563,1.667 3,1.896 0.438,0.229 10 false IL+2
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G12-12 (IL+2) - Body ground Light control switch TAIL or HEAD 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


C237718
3.385,0.125 3.719,0.375 0.333,0.25 3,0.583 3.073,0.583 3.073,0.583 3.552,0.844 true 2.865,0.208 2.979,0.208 2.979,0.208 3.698,0.75 true 2.667,0.51 3.031,0.708 0.365,0.198 10 false EAU 2.542,0.135 2.906,0.333 0.365,0.198 10 false IL+2 3.479,0.167 3.844,0.365 0.365,0.198 10 false z3
*A w/ Multi-information Display - -


b.

Connect the positive (+) lead of the battery to terminal z3-5 (IL+2) and the negative (-) lead to terminal z3-8 (EAU) of the steering pad switch assembly connector.


c.

Check if the illumination for the steering pad switch assembly comes on.

OK:

Illumination for the steering pad switch assembly comes on.



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

C282256
1.958,0.979 1.729,0.604 true 2.375,0.99 1.917,0.708 true 5.656,2.427 5.292,1.958 true 5.188,2.385 5.135,2.031 true 1.375,0.156 1.688,0.354 0.313,0.198 10 false *a 4.604,1.448 4.917,1.646 0.313,0.198 10 false *b 1.875,1.021 2.333,1.219 0.458,0.198 10 false IL+2 2.302,1.021 2.76,1.219 0.458,0.198 10 false EAU 5.667,2.427 6.125,2.625 0.458,0.198 10 false IL+2 5.135,2.427 5.594,2.625 0.458,0.198 10 false EAU
*a Steering Pad Switch Side *b Vehicle Side


Standard Resistance:
Tester Connection Condition Specified Condition
8 (EAU) - 4 (EAU) Spiral cable is turned 2.5 rotations counterclockwise Below 1 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
5 (IL+2) - 12 (IL+2) Spiral cable is turned 2.5 rotations counterclockwise
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise


CAUTION:

The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)
a.

Disconnect the G1 radio receiver assembly connector.


b.

Disconnect the G12 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-23 (SWG) - G12-4 (EAU) Always Below 1 Ω
G1-23 (SWG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BATTERY AND BODY GROUND)
a.

Disconnect the G5 radio receiver assembly connector.


E178447
1.5,0.417 1.927,0.667 0.427,0.25 2.135,1.385 2.5,1.76 true 1.604,1.375 1.25,1.771 true 0.167,0.115 0.5,0.333 0.333,0.219 10 false *a 2.552,1.708 3.01,1.948 0.458,0.24 10 false ILL+ 1.604,0.469 1.917,0.667 0.313,0.198 10 false G5 0.885,1.708 1.448,1.948 0.563,0.24 10 false GND
*a Front view of wire harness connector
(to Radio Receiver Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G5-10 (ILL+) - Body ground Light control switch TAIL or HEAD 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR