Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM1880E _56 Audio / Visual / Telematics _013234 AUDIO / VIDEO _0068593 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Speaker Circuit  


DESCRIPTION

The radio receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM

C240170
5.817,6.538 6.82,6.941 1.003,0.403 10 Radio Receiver Assembly 5.878,3.051 6.159,3.221 0.281,0.17 10 FL- 5.878,2.531 6.159,2.701 0.281,0.17 10 FL+ 5.521,3.051 5.806,3.221 0.286,0.17 10 G5 5.521,2.531 5.803,2.701 0.283,0.17 10 G5 5.878,1.653 6.18,1.823 0.302,0.17 10 FR- 5.878,1.132 6.18,1.303 0.302,0.17 10 FR+ 5.521,1.653 5.743,1.823 0.223,0.17 10 G5 5.521,1.132 5.743,1.303 0.223,0.17 10 G5 2.95,2.045 5.622,2.246 2.672,0.201 10 Front No. 2 Speaker Assembly RH* 2.95,3.447 5.242,3.648 2.293,0.201 10 Front No. 2 Speaker Assembly LH* 0.729,1.216 2.031,1.567 1.302,0.351 10 Front No. 1 Speaker Assembly RH 0.729,2.625 2.031,3.004 1.302,0.379 10 Front No. 1 Speaker Assembly LH 5.572,0.924 5.698,1.095 0.126,0.171 10 1 5.572,1.441 5.698,1.611 0.126,0.171 10 5 5.572,2.314 5.698,2.485 0.126,0.171 10 2 5.572,2.831 5.698,3.001 0.126,0.171 10 6 4.346,1.05 4.472,1.221 0.126,0.171 10 4 4.346,1.567 4.472,1.737 0.126,0.171 10 2 3.901,1.032 4.37,1.202 0.469,0.171 10 TWR+ 3.928,1.769 4.336,1.94 0.409,0.171 10 TWR- 3.512,1.05 3.638,1.221 0.126,0.171 10 3 3.512,1.567 3.638,1.737 0.126,0.171 10 1 3.694,1.06 3.82,1.23 0.126,0.171 10 + 3.694,1.737 3.82,1.908 0.126,0.171 10 - 3.896,2.433 4.365,2.603 0.469,0.171 10 TWL+ 3.922,3.17 4.331,3.341 0.409,0.171 10 TWL- 3.683,2.461 3.809,2.631 0.126,0.171 10 + 3.683,3.138 3.809,3.309 0.126,0.171 10 - 4.346,2.444 4.472,2.615 0.126,0.171 10 4 4.346,2.961 4.472,3.131 0.126,0.171 10 2 3.512,2.444 3.638,2.615 0.126,0.171 10 3 3.512,2.961 3.638,3.131 0.126,0.171 10 1 2.311,1.526 2.438,1.696 0.126,0.171 10 2 2.311,1.264 2.438,1.435 0.126,0.171 10 1 2.311,2.933 2.438,3.104 0.126,0.171 10 2 2.311,2.672 2.438,2.842 0.126,0.171 10 1 5.878,5.848 6.159,6.018 0.281,0.17 10 RL- 5.878,5.331 6.159,5.501 0.281,0.17 10 RL+ 5.521,5.848 5.732,6.018 0.212,0.17 10 G4 5.521,5.331 5.732,5.501 0.212,0.17 10 G4 5.878,4.45 6.18,4.62 0.302,0.17 10 RR- 5.878,3.937 6.18,4.107 0.302,0.17 10 RR+ 5.521,4.45 5.743,4.62 0.222,0.17 10 G4 5.521,3.937 5.743,4.107 0.222,0.17 10 G4 5.572,3.701 5.698,3.872 0.126,0.171 10 1 5.572,4.218 5.698,4.388 0.126,0.171 10 3 5.572,5.107 5.698,5.278 0.126,0.171 10 2 5.572,5.624 5.698,5.794 0.126,0.171 10 6 0.729,4.015 2.038,4.409 1.309,0.393 10 Rear Speaker Assembly RH 0.729,5.41 2.031,5.779 1.302,0.369 10 Rear Speaker Assembly LH 0.458,6.979 1.551,7.157 1.094,0.178 10 *: for 6 Speakers 2.311,5.471 2.438,5.642 0.126,0.171 10 1 2.311,5.741 2.438,5.912 0.126,0.171 10 2 2.311,4.042 2.438,4.212 0.126,0.171 10 1 2.311,4.312 2.438,4.483 0.126,0.171 10 2 2.95,1.902 3.261,2.072 0.311,0.17 10 H6 2.95,3.303 3.261,3.473 0.311,0.17 10 I6 0.729,1.041 1.04,1.211 0.311,0.17 10 H4 0.729,2.455 1.04,2.625 0.311,0.17 10 I1 0.729,3.845 1.04,4.015 0.311,0.17 10 J7 0.729,5.247 1.04,5.417 0.311,0.17 10 J3

PROCEDURE

1.CHECK SPEAKER
a.

Check the malfunctioning speakers.

Result:
Result Proceed to
Malfunction in front speaker area (for 6 Speakers) A
Malfunction in front speaker area (for 4 Speakers) B
Malfunction in rear speaker area C




A

2.CHECK FRONT SIDE SPEAKER

B

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

C

8.INSPECT REAR SPEAKER ASSEMBLY
2.CHECK FRONT SIDE SPEAKER
a.

Check the malfunctioning speakers.

Result:
Result Proceed to
Front No. 2 speaker assembly A
Front No. 1 speaker assembly B




A

3.INSPECT FRONT NO.2 SPEAKER ASSEMBLY

B

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
3.INSPECT FRONT NO.2 SPEAKER ASSEMBLY
a.

Temporarily replace the speaker with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Check that the malfunction disappears.

HINT:
·

Connect all the speaker connectors to the speakers.

·

When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.



Result:
Result Proceed to
Malfunction does not disappear A
Malfunction disappears B




A

4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 2 SPEAKER)

B

REPLACE FRONT NO.2 SPEAKER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 2 SPEAKER)
a.

Disconnect the G5 radio receiver assembly connector.


b.

Disconnect the H6*1 and/or I6*2 speaker connector.

*1: for RH

*2: for LH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
G5-1 (FR+) - H6-4 (TWR+) Always Below 1 Ω
G5-5 (FR-) - H6-2 (TWR-)
G5-1 (FR+) - Body ground Always 10 kΩ or higher
G5-5 (FR-) - Body ground

for LH
Tester Connection Condition Specified Condition
G5-2 (FL+) - I6-4 (TWL+) Always Below 1 Ω
G5-6 (FL-) - I6-2 (TWL-)
G5-2 (FL+) - Body ground Always 10 kΩ or higher
G5-6 (FL-) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Disconnect the H4*1 and/or I1*2 speaker connector.

*1: for RH

*2: for LH



b.
E178457

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 4 Ω


Result:
Result Proceed to
OK (for 6 Speakers) A
OK (for 4 Speakers) B
NG C




A

6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)

B

7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 1 SPEAKER)

C

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)

*1: for RH

*2: for LH


a.

Disconnect the H6*1 and/or I6*2 speaker connector.


b.

Disconnect the H4*1 and/or I1*2 speaker connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
H6-3 (+) - H4-1 Always Below 1 Ω
H6-1 (-) - H4-2
H6-3 (+) - Body ground Always 10 kΩ or higher
H6-1 (-) - Body ground

for LH
Tester Connection Condition Specified Condition
I6-3 (+) - I1-1 Always Below 1 Ω
I6-1 (-) - I1-2
I6-3 (+) - Body ground Always 10 kΩ or higher
I6-1 (-) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE FRONT NO.2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 1 SPEAKER)
a.

Disconnect the G5 radio receiver assembly connector.


b.

Disconnect the H4*1 and/or I1*2 speaker connector.

*1: for RH

*2: for LH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
G5-1 (FR+) - H4-1 Always Below 1 Ω
G5-5 (FR-) - H4-2
G5-1 (FR+) - Body ground Always 10 kΩ or higher
G5-5 (FR-) - Body ground

for LH
Tester Connection Condition Specified Condition
G5-2 (FL+) - I1-1 Always Below 1 Ω
G5-6 (FL-) - I1-2
G5-2 (FL+) - Body ground Always 10 kΩ or higher
G5-6 (FL-) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR SPEAKER ASSEMBLY
a.

Disconnect the J7*1 and/or J3*2 speaker connector.

*1: for RH

*2: for LH



b.
E178457

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 4 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR SPEAKER)

NG

9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR SPEAKER)
a.

Disconnect the G4 radio receiver assembly connector.


b.

Disconnect the J7*1 and/or J3*2 speaker connector.

*1: for RH

*2: for LH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
G4-1 (RR+) - J7-1 Always Below 1 Ω
G4-3 (RR-) - J7-2
G4-1 (RR+) - Body ground Always 10 kΩ or higher
G4-3 (RR-) - Body ground

for LH
Tester Connection Condition Specified Condition
G4-2 (RL+) - J3-1 Always Below 1 Ω
G4-6 (RL-) - J3-2
G4-2 (RL+) - Body ground Always 10 kΩ or higher
G4-6 (RL-) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR