The driver side junction block assembly drivers the door lock motors according to switch signals from the door control switch of the power window regulator master switch assembly and driver side door ley cylinder.
However, the driver side door key-linked lock/unlock function will not operate when the driver side seat belt is fastened.
When replacing the theft warning ECU assembly (w/ Theft Deterrent System) or door control transmitter sub-assembly, refer to the registration procedures.
w/ Theft Deterrent System: See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System)>REGISTRATION
w/o Theft Deterrent System: See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Theft Deterrent System)>REGISTRATION
Check the power door lock operation.
| Result | Proceed |
|---|---|
| No doors can be locked using power window regulator master switch assembly (door control switch) | A |
| No doors can be locked using key-linked switch | B |
A
B
Remove the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *a | Lock | *b | Unlock |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Lock | Below 1 Ω |
| 3 - 5, 3 - 8 | OFF | 10 kΩ or higher |
| 3 - 8 | Unlock | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - 5 | Lock | Below 1 Ω |
| 1 - 5, 1 - 8 | OFF | 10 kΩ or higher |
| 1 - 8 | Unlock | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I12*1 or H8*2 power window regulator master switch assembly connector.
*1: for LHD
*2: for RHD
Disconnect the 2A and 2D driver side junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I12-5 (L) - 2A-4 (L1) | Always | Below 1 Ω |
| I12-8 (UL) - 2D-4 (UL1) | Always | Below 1 Ω |
| I12-3 (E) - Body ground | Always | Below 1 Ω |
| I12-5 (L) or 2A-4 (L1) - Body ground | Always | 10 kΩ or higher |
| I12-8 (UL) or 2D-4 (UL1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H8-5 (L) - 2A-4 (L1) | Always | Below 1 Ω |
| H8-8 (UL) - 2D-4 (UL1) | Always | Below 1 Ω |
| H8-1 (E) - Body ground | Always | Below 1 Ω |
| H8-5 (L) or 2A-4 (L1) - Body ground | Always | 10 kΩ or higher |
| H8-8 (UL) or 2D-4 (UL1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front door lock assembly (for Driver Side).
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *a | Lock | *b | Off |
| *c | Unlock | - | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 7 - 9 | Lock | Below 1 Ω |
| 7 - 9, 7 - 10 | OFF | 10 kΩ or higher |
| 7 - 10 | Unlock | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 6 - 8 | Lock | Below 1 Ω |
| 5 - 8, 6 - 8 | OFF | 10 kΩ or higher |
| 5 - 8 | Unlock | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
When the driver side seat belt is not fastened, check that the driver side seat belt warning light in the combination meter assembly blinks.
When the driver side seat belt is fastened, check that the driver side seat belt warning light in the combination meter assembly turns off.
Driver side seat belt warning light blinks and turns off according to above operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for LHD
*2: for RHD
Disconnect K1*1 or K2*2 front seat inner belt assembly (for Driver Side) connector.
Disconnect the I2*1 or H1*2 front door lock assembly (for Driver Side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-1 (+) - I2-7 (E) | Always | Below 1 Ω |
| K1-1 (+) or I2-7 (E) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-1 (+) - H1-8 (E) | Always | Below 1 Ω |
| K2-1 (+) or H1-8 (E) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I1*2 or H1*2 front door lock assembly (for Driver Side) connector.
*1: for LHD
*1: for RHD
Disconnect the 2A and 2D driver side junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I2-10 (UL) - 2D-4 (UL1) | Always | Below 1 Ω |
| I2-9 (L) - 2A-4 (L1) | Always | Below 1 Ω |
| I2-7 (E) - Body ground | Driver side seat belt is not fastened | Below 1 Ω |
| I2-10 (UL) or 2D-4 (UL1) - Body ground | Always | 10 kΩ or higher |
| I2-9 (L) or 2A-4 (L1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H1-5 (UL) - 2D-4 (UL1) | Always | Below 1 Ω |
| H1-6 (L) - 2A-4 (L1) | Always | Below 1 Ω |
| H1-8 (E) - Body ground | Driver side seat belt is not fastened | Below 1 Ω |
| H1-5 (UL) or 2D-4 (UL1) - Body ground | Always | 10 kΩ or higher |
| H1-6 (L) or 2A-4 (L1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG