Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Theft Deterrent System)
RM1880E _58 Vehicle Interior _013237 DOOR LOCK _0068607 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Theft Deterrent System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Theft Deterrent System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the door control transmitter assembly and sends these signals to the driver side junction block assembly. The driver side junction block assembly then controls all doors by sending lock/unlock signals to each door.

WIRING DIAGRAM

B284788
5.667,0.656 6.167,0.958 0.5,0.302 10 false BECU 4.979,0.656 5.26,0.958 0.281,0.302 10 false 2L 4.979,0.438 5.302,0.74 0.323,0.302 10 false 12 4.083,0.802 4.646,1.135 0.563,0.333 10 false ECU-B 3.24,0.813 3.656,1.135 0.417,0.323 10 false DCC 1.354,1.469 1.667,1.771 0.313,0.302 10 false +B 1.656,1.365 1.917,1.635 0.26,0.271 10 false 5 1.24,1.896 1.667,2.198 0.427,0.302 10 false RDA 1.656,1.792 1.885,2.042 0.229,0.25 10 false 2 1.24,2.323 1.74,2.667 0.5,0.344 10 false PRG 5.667,1.896 6.094,2.208 0.427,0.313 10 false RDA 5.677,2.323 6.156,2.635 0.479,0.313 10 false PRG 1.656,2.219 1.906,2.51 0.25,0.292 10 false 3 1.25,2.76 1.646,3.135 0.396,0.375 10 false GND 1.656,2.656 1.906,2.938 0.25,0.281 10 false 1 0.417,3.01 0.875,3.417 0.458,0.406 10 false K37 0.417,3.177 1.823,3.615 1.406,0.438 10 false Door Control Receiver 1.677,3.885 2.052,4.219 0.375,0.333 10 false G10 1.698,4.052 3.813,4.438 2.115,0.385 10 false Unlock Warning Switch Assembly 4.906,4.979 6.667,5.385 1.76,0.406 10 false Driver Side Junction Block Assembly (Integrated Relay) 1.552,0.635 2.406,0.969 0.854,0.333 10 false from Battery 4.979,1.458 5.281,1.719 0.302,0.26 10 false 2K 4.979,1.281 5.25,1.542 0.271,0.26 10 false 12 4.979,1.906 5.313,2.188 0.333,0.281 10 false 2D 5.031,1.698 5.313,2.01 0.281,0.313 10 false 2 5.021,2.115 5.354,2.438 0.333,0.323 10 false 5 4.979,2.313 5.313,2.583 0.333,0.271 10 false 2D 4.969,3.656 5.281,3.969 0.313,0.313 10 false 2O 4.969,3.448 5.302,3.719 0.333,0.271 10 false 10 5.448,0.573 5.698,0.844 0.25,0.271 10 false 4 5.406,1.792 5.698,2.125 0.292,0.333 10 false 12 5.406,2.219 5.74,2.51 0.333,0.292 10 false 10 5.656,3.646 6.125,3.979 0.469,0.333 10 false KSW 5.406,3.563 5.708,3.875 0.302,0.313 10 false 17 3.438,3.552 3.698,3.844 0.26,0.292 10 false 1 3.073,3.552 3.5,3.885 0.427,0.333 10 false UN+ 2.219,3.563 2.594,3.906 0.375,0.344 10 false UN- 2.063,3.563 2.365,3.875 0.302,0.313 10 false 2 4.969,4.063 5.271,4.344 0.302,0.281 10 false 2D 5.01,3.854 5.26,4.146 0.25,0.292 10 false 9 5.656,4.063 6.135,4.365 0.479,0.302 10 false GND 5.469,3.979 5.698,4.25 0.229,0.271 10 false 1 4.979,4.469 5.292,4.75 0.313,0.281 10 false 2D 4.979,4.271 5.26,4.552 0.281,0.281 10 false 18

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the door control receiver or door control transmitter assembly, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Theft Deterrent System)>REGISTRATION).



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Each door locks and unlocks normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY

NG

2.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY
a.

Check whether the wireless door lock control functions operate normally with another registered transmitter.

OK:

Wireless door lock control functions operate normally.


Result:
Proceed to
OK
NG




OK

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY (LED)

NG

5.CHECK FOR ELECTRICAL NOISE
3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY (LED)
a.

Press and hold the lock switch of the door control transmitter assembly for 5 seconds and check the number of times that the transmitter LED illuminates.

Result:
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not third time C




A

4.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE DOOR CONTROL TRANSMITTER SUB-ASSEMBLY

C

REPLACE TRANSMITTER BATTERY

4.INSPECT TRANSMITTER BATTERY (VOLTAGE)
B262355

a.

Remove the battery from the door control transmitter assembly that does not operate.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT


b.

Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.



c.

Carefully extend the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before starting work, remove any static electricity that has built up by touching, for example, the vehicle to prevent the door control transmitter sub-assembly from being damaged.



d.

Measure the voltage according to the value(s) in the table below.

HINT:
·

Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter assembly.

·

Perform the measurement when the door control transmitter assembly is at room temperature.



Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive (+) - Battery negative (-) Ignition switch off, all doors closed and lock or unlock switch pushed 2.2 to 3.2 V



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

5.CHECK FOR ELECTRICAL NOISE
a.

Move the door control transmitter assembly in the vicinity of the door control receiver.

HINT:

Refer to Parts Location for the location of the door control receiver.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Theft Deterrent System)>PARTS LOCATION



b.

Press and hold either the lock or unlock transmitter switch for 1 second and check that the doors lock or unlock accordingly.

OK:

Wireless door lock control functions operate normally.


HINT:
·

Check if electrical noise is the cause by moving the door control transmitter assembly closer to the door control receiver. Moving it closer will decrease the effects of electrical noise.

·

If the operation check can be performed normally, there is a high probability that electrical noise or a decrease in output from the door control transmitter assembly is the cause of the malfunction. There is a high probability that electrical noise is the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.




Result:
Proceed to
OK
NG



OK

FIND CAUSE OF NOISE AND REMOVE IT

NG

6.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - DRIVER SIDE JUNCTION BLOCK)
6.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - DRIVER SIDE JUNCTION BLOCK)
a.

Disconnect the K37 door lock control receiver connector.


b.

Disconnect the 2D and 2K driver side junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K37-2 (RDA) - 2D-2 (RDA) Always Below 1 Ω
K37-3 (PRG) - 2D-5 (PRG) Always Below 1 Ω
K37-5 (+B) - 2K-12 (BECU) Always Below 1 Ω
K37-2 (RDA) or 2D-2 (RDA) - Body ground Always 10 kΩ or higher
K37-3 (PRG) or 2D-5 (PRG) - Body ground Always 10 kΩ or higher
K37-5 (+B) or 2K-12 (BECU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.

Disconnect the K37 door control receiver connector.


B219541
0.5,1 0.917,1.25 0.417,0.25 1.198,1.375 0.958,1.75 0.958,1.75 0.802,1.75 true 2.26,1.375 2.49,1.75 2.49,1.75 2.646,1.75 true 0.438,1.677 0.823,1.948 0.385,0.271 10 GND 2.698,1.656 3.052,1.844 0.354,0.188 10 +B 0.146,0.063 0.344,0.25 0.198,0.188 10 *a 0.573,1.042 0.948,1.292 0.375,0.25 10 K37
*a Front view of wire harness connector
(to Door Control Receiver)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K37-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K37-5 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.
B260824
0.76,1 1.177,1.25 0.417,0.25 1.854,1.51 2.344,1.885 2.344,1.885 2.49,1.885 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 0.854,1.052 1.313,1.25 0.458,0.198 10 false K37 2.583,1.792 3.042,1.99 0.458,0.198 10 false RDA
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K37-2 (RDA) - Body ground Ignition switch off, all doors closed and transmitter switch not pressed 11 to 14 V
Ignition switch off, all doors closed and transmitter switch pressed Pulse generation



Result:
Proceed to
OK
NG



OK

9.INSPECT UNLOCK WARNING SWITCH ASSEMBLY

NG

REPLACE DOOR CONTROL RECEIVER

9.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.
B274206
0.615,1.094 0.896,1.365 0.281,0.271 10 false *a 1.229,1.365 1.479,1.594 0.25,0.229 10 false *b
*a Pushed
*b Not pushed


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pushed Below 1 Ω
Not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - DRIVER SIDE JUNCTION BLOCK AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - DRIVER SIDE JUNCTION BLOCK AND BODY GROUND)
a.

Disconnect the G10 unlock warning switch assembly connector.


b.

Disconnect the 2O driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-1 (UN+) - 2O-10 (KSW) Always Below 1 Ω
G10-1 (UN+) or 2O-10 (KSW) - Body ground Always 10 kΩ or higher
G10-2 (UN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR