Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068615 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2796  No Communication in Immobiliser System  B2798  Communication Malfunction No. 2  


DESCRIPTION

DTC B2796 is stored when a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU assembly.

DTC B2798 is stored when a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
B2796 No Communication in Immobiliser System The key code cannot be transmitted (1 trip detection logic*).
·

Key

·

Transponder key amplifier

·

Harness or connector

·

Transponder key ECU assembly


Transponder Key ECU Assembly
DTC Output Confirmation Operation

Insert the key into the ignition key cylinder


B2798 Communication Malfunction No. 2 Key code identification cannot be completed within the specified time (1 trip detection logic*). Key Transponder Key ECU Assembly
DTC Output Confirmation Operation

Insert the key into the ignition key cylinder



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started. -

Related Data List and Active Test
DTC Code Data List and Active Test
B2796 Response
B2798 Frame Error

WIRING DIAGRAM

B278720
0.875,0.771 1.708,1.208 0.833,0.438 10 false Transponder Key Coil 1.25,2.125 3.552,2.542 2.302,0.417 10 false Transponder Key Amplifier 4.948,2.125 7.073,2.729 2.125,0.604 10 false Transponder Key ECU Assembly 1.25,1.969 1.875,2.219 0.625,0.25 10 false G28 4.948,1.948 5.552,2.292 0.604,0.344 10 false G26 5.49,0.427 6.156,0.865 0.667,0.438 10 false VC5 5.188,0.333 5.594,0.719 0.406,0.385 10 false 14 3.406,0.333 3.865,0.75 0.458,0.417 10 false 1 5.188,0.698 5.771,1.156 0.583,0.458 10 false 15 3.406,0.688 3.792,1.042 0.385,0.354 10 false 4 5.25,1.052 5.906,1.573 0.656,0.521 10 false 4 3.406,1.052 3.781,1.333 0.375,0.281 10 false 5 5.25,1.417 5.698,1.917 0.448,0.5 10 false 5 3.406,1.427 3.667,1.656 0.26,0.229 10 false 7 5.469,0.781 6.219,1.375 0.75,0.594 10 false CODE 5.49,1.156 6.479,1.813 0.99,0.656 10 false TXCT 5.49,1.521 6.302,2.042 0.813,0.521 10 false AGND 3.042,0.333 3.521,0.615 0.479,0.281 10 false VC5 1.844,0.313 2.49,0.656 0.646,0.344 10 false ANT2 1.854,1.656 2.5,1.948 0.646,0.292 10 false ANT1 2.917,0.688 3.552,1.052 0.635,0.365 10 false CODE 2.948,1.052 3.625,1.49 0.677,0.438 10 false TXCT 2.917,1.427 3.583,1.938 0.667,0.51 10 false AGND

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
OK:

DTC B2796 or B2798 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM)
3.READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM)
a.

Use the Data List to check if the engine immobiliser system is functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Immobiliser > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system status determined by transponder key ECU assembly Set or Unset Set: Engine immobiliser set (engine start prohibited [no key in ignition key cylinder])
Unset: Engine immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.
Body Electrical > Immobiliser > Data List
Tester Display
Immobiliser
50003 260 8
OK:

Set (the key is not inserted in the ignition key cylinder) and Unset (the key is inserted in the ignition key cylinder) appear on the screen according to the key insertion condition.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

4.CHECK WHETHER ENGINE STARTS WITH OTHER KEY
4.CHECK WHETHER ENGINE STARTS WITH OTHER KEY
a.

Check whether the engine starts with an already registered vehicle key.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

REREGISTER OR REPLACE KEY THAT CANNOT START ENGINE

NG

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
a.

Disconnect the G26 transponder key ECU assembly connector.


b.

Disconnect the G28 transponder key amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G26-14 (VC5) - G28-1 (VC5) Always Below 1 Ω
G26-15 (CODE) - G28-4 (CODE) Always Below 1 Ω
G26-4 (TXCT) - G28-5 (TXCT) Always Below 1 Ω
G26-5 (AGND) - G28-7 (AGND) Always Below 1 Ω
G26-14 (VC5) or G28-1 (VC5) - Body ground Always 10 kΩ or higher
G26-15 (CODE) or G28-4 (CODE) - Body ground Always 10 kΩ or higher
G26-4 (TXCT) or G28-5 (TXCT) - Body ground Always 10 kΩ or higher
]G26-5 (AGND) or G28-7 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE TRANSPONDER KEY AMPLIFIER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TRANSPONDER KEY AMPLIFIER
a.

Temporally replace the transponder key amplifier with a new or normally functioning one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY AMPLIFIER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER ENGINE STARTS
7.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY AMPLIFIER IS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY