Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068615 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck on HI output, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output (1 trip detection logic*).
·

Harness or connector

·

Transponder key ECU assembly

·

ECM


ECM
DTC Output Confirmation Operation

Turn the ignition switch to ON and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stop). Engine cannot be started.

Related Data List and Active Test
DTC Code Data List and Active Test
B279A -

WIRING DIAGRAM

B281162
5.479,0.604 6.375,1.26 0.896,0.656 10 false +B 4.708,0.76 5.469,1.188 0.76,0.427 10 false ECU-B 4.25,0.76 4.813,1.26 0.563,0.5 10 false DCC 1.156,1.802 1.875,2.146 0.719,0.344 10 false G88 1.156,1.948 2.094,2.417 0.938,0.469 10 false ECM 2.948,0.583 3.875,0.917 0.927,0.333 10 false from Battery 5.281,0.5 5.698,0.854 0.417,0.354 10 false 1 5.49,0.99 6.313,1.448 0.823,0.458 10 false EFIO 1.49,0.99 2.167,1.5 0.677,0.51 10 false IMI 5.229,0.906 5.677,1.292 0.448,0.385 10 false 13 5.479,1.438 6.104,1.885 0.625,0.448 10 false GND 4.844,1.76 5.563,2.188 0.719,0.427 10 false G26 4.844,1.896 7.104,2.552 2.26,0.656 10 false Transponder Key ECU Assembly 5.219,1.344 5.708,1.656 0.49,0.313 10 false 16 1.781,0.906 2.385,1.354 0.604,0.448 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly or ECM, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

After troubleshooting for this DTC, make sure B279A is not present. If present, troubleshoot the SFI system DTCs next.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
No DTC is output A
DTC B279A and other DTCs are output B
DTC B279A is output C


HINT:

If any DTCs other than B279A are output, troubleshoot those DTCs first.




A

B

C

3.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)
3.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)
a.

Disconnect the G26 transponder key ECU assembly connector.


b.

Disconnect the G88 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G88-16 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G88-16 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G88-16 (IMI) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.
B274402
0.583,1.146 0.969,1.385 0.385,0.24 1.313,1.427 1.094,1.792 1.094,1.792 0.896,1.792 true 1.563,1.427 1.375,2.135 1.375,2.135 1.177,2.135 true 0.073,0.073 0.479,0.385 0.406,0.313 10 false *a 0.083,2.406 0.563,2.656 0.479,0.25 10 false *1 0.271,3.365 1,3.917 0.729,0.552 10 false GND 0.552,1.729 1.333,2.083 0.781,0.354 10 false GND 0.656,1.188 0.938,1.365 0.281,0.177 10 false G26 0.833,2.052 1.615,2.448 0.781,0.396 10 false EFIO
*1 Waveform
*a Component with harness connected
(Transponder Key ECU Assembly)


Using an oscilloscope, check the waveform.

Measurement Condition:
Item Content
Tester Connection G26-13 (EFIO) - G26-16 (GND)
Tool Setting 10V/DIV., 100 ms./DIV.
Condition Ignition switch ON


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
a.

Disconnect the G26 transponder key ECU assembly connector.


B274403
0.208,1.219 0.625,1.469 0.417,0.25 0.969,1.271 0.75,1.01 0.75,1.01 0.542,1.01 true 2.427,1.531 2.646,1.792 2.646,1.792 2.854,1.792 true 0.104,0.094 0.5,0.396 0.396,0.302 10 false *a 0.281,1.26 0.813,1.594 0.531,0.333 10 false G26 0.281,0.927 0.604,1.104 0.323,0.177 10 false +B 2.906,1.708 3.396,1.969 0.49,0.26 10 false GND
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G26-16 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G26-1 (+B) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
OK:

DTC B279A is not output.



Result:
Proceed to
OK
NG



OK

END (ECM IS DEFECTIVE)