Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068616 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Ignition Switch Circuit  


DESCRIPTION

When the ignition switch assembly is turned to ON, voltage is applied to terminal IG of the theft warning ECU assembly.

WIRING DIAGRAM

B278733
4.917,2.083 6.917,2.333 2,0.25 10 false Theft Warning ECU Assembly 4.917,1.917 5.365,2.323 0.448,0.406 10 false G124 5.448,0.583 5.688,0.813 0.24,0.229 10 false IG 5.448,1.531 5.688,1.771 0.24,0.24 10 false E 5.219,0.458 5.469,0.667 0.25,0.208 10 false 4 3.135,0.458 3.417,0.667 0.281,0.208 10 false 1 1.896,0.458 2.083,0.667 0.188,0.208 10 false 4 5.198,1.406 5.396,1.594 0.198,0.188 10 false 1 3.833,0.75 5.115,1.021 1.281,0.271 10 false ECU-IG&GAUGE 0.635,0.573 1.583,0.802 0.948,0.229 10 false from Battery 1.75,1.083 3.438,1.385 1.688,0.302 10 false Ignition Switch Assembly 1.75,0.917 2.104,1.125 0.354,0.208 10 false G9 2.781,0.698 3.094,0.906 0.313,0.208 10 false IG1 2.083,0.698 2.51,0.917 0.427,0.219 10 false AM1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the theft warning ECU assembly, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System)>REGISTRATION).



PROCEDURE

1.INSPECT IGNITION SWITCH ASSEMBLY
a.

Remove the ignition switch assembly.

Click hereEngine / Hybrid System>2TR-FE STARTING>IGNITION SWITCH>REMOVAL


b.
B275965
1.167,1 0.854,0.573 0.854,0.573 0.646,0.573 true 2,1.01 2.302,0.573 2.302,0.573 2.521,0.573 true 0.26,0.49 0.667,0.75 0.406,0.26 10 AM1 2.583,0.49 2.958,0.75 0.375,0.26 10 IG1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (IG1) - 4 (AM1) Off, ACC 10 kΩ or higher
ON, Start Below 1 Ω


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)

NG

REPLACE IGNITION SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)
a.

Disconnect the G124 theft warning ECU assembly connector.


B274165
0.25,1.083 0.667,1.333 0.417,0.25 0.865,1.188 0.625,0.885 0.625,0.885 0.448,0.885 true 1.25,1.208 0.802,0.563 0.802,0.563 0.625,0.563 true 0.083,0.083 0.427,0.302 0.344,0.219 10 false *a 0.302,1.125 0.646,1.385 0.344,0.26 10 false G124 0.458,0.5 0.677,0.708 0.219,0.208 10 false IG 0.292,0.802 0.469,1 0.177,0.198 10 false E
*a Front view of wire harness connector
(to Theft Warning ECU Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G124-1 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G124-4 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR