Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY
RM1880E _58 Vehicle Interior _013242 SUPPLEMENTAL RESTRAINT SYSTEMS _0068638 FRONT PASSENGER AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

HINT:

When scrapping a vehicle equipped with an SRS or disposing of the instrument panel passenger airbag, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the service department of the distributor.


CAUTION:
·

Never dispose of a instrument panel passenger airbag assembly with an inactivated airbag.

·

The airbag produces a loud, exploding sound when it activates. Perform the operation where it will not be a nuisance to people nearby.

·

When activating the airbag, always use the specified SST (SRS airbag deployment tool).

·

Perform procedures in a place away from electrical interference.

·

When activating the airbag, stand at least 10 m (32.8 ft.) away from the airbag.

·

The airbag becomes very hot when it is deployed. Do not touch it for at least 30 minutes after activation.

·

Use gloves and safety glasses when handling a deployed airbag.

·

Do not apply water to a deployed airbag.

·

Always wash your hands with water after completing the operation.



Hide 2.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)

HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371
0.938,1.219 0.938,0.896 0.938,0.896 0.74,0.896 false 0.427,0.833 0.76,1.063 0.333,0.229 10 false SST

Check the function of SST (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).



c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



d.

Remove the instrument panel passenger airbag assembly assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL).


e.
B290004

Install SST.

i.

Disconnect the connector.

NOTICE:

When handling the airbag connector, do not damage the airbag wire harness.



ii.
B290005
1.896,1.896 1.635,1.813 true 1.917,1.813 2.344,2.177 0.427,0.365 10 false SST

Connect SST connector to the instrument panel wire.

SST
09082-00700  
09082-00780  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.



iii.
C281354
1.708,0.833 1.969,0.375 1.969,0.375 2.135,0.375 true 0.594,1.563 0.594,1.323 0.594,1.323 0.396,1.323 true 2.167,0.292 2.479,0.604 0.313,0.313 10 false *1 1.677,1.677 1.979,1.969 0.302,0.292 10 false *a 0.115,1.24 0.5,1.5 0.385,0.26 10 false SST
*1 Battery
*a 10 m or more


Move SST at least 10 m (32.8 ft.) away from the front side window.


iv.

Maintaining enough clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



v.

Connect the SST red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.



f.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the airbag.

CAUTION:
·

When deploying the airbag, make sure that no one is near the vehicle.

·

The airbag becomes extremely hot when it is deployed. Do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a deployed airbag.

·

Do not apply water to a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




Hide 3.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

NOTICE:

Be sure to follow the procedure detailed below when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371
0.958,1.208 0.958,0.854 0.958,0.854 0.719,0.854 false 0.406,0.771 0.771,0.99 0.365,0.219 10 false SST

Check the function of SST (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


b.

Remove the instrument panel passenger airbag assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL).

CAUTION:
·

When removing the airbag, work must be started 90 seconds after the ignition switch is turned OFF and after the cable is disconnected from the negative (-) battery terminal.

·

When storing the airbag, keep the airbag deployment side facing upward.




c.
B104882
1.854,1.24 1.854,1.625 false 2.656,0.49 3.052,0.854 0.396,0.365 10 false *a 1.781,1.656 2.156,2 0.375,0.344 10 false *b
*a Wire Harness Diameter
*b Stripped Wire Harness Section


Using service wire harnesses for the vehicle, tie down the airbag to a tire.

Cross-sectional area of stripped wire harness section:

1.25 mm2 (0.0019 in.2 ) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie the instrument panel passenger airbag assembly, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.00192 in.2).


HINT:

To calculate the cross-sectional area of the stripped wire harness section: Cross-sectional area = 3.14 x (Diameter)2 / 4


i.

Position the airbag inside the tire so that the brackets contact the tire.

B112124
3.332,2.348 4.002,2.699 0.67,0.351 10 *b 0.483,3.105 0.908,3.298 0.425,0.193 10 *a
*a Width *b Inner Diameter


Tire size:

Must exceed the following dimensions

Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (14.2 in.)



ii.

Tie the instrument panel passenger airbag assembly to the tire with several wire harnesses

CAUTION:
·

Make sure that the wire harnesses are tight. If there is slack in the wire harnesses, the instrument panel passenger airbag may become loose due to the shock when the airbag is deployed.

·

Always tie the instrument panel passenger airbag with the airbag deployment side facing inside.



NOTICE:

As the tire may be damaged by the airbag deployment, use a tire that you are planning to throw away.




d.
B112125
0.667,0.719 0.667,0.469 0.667,0.469 0.583,0.469 false 0.302,0.396 0.781,0.729 0.479,0.333 10 false SST

Install SST.

i.

Connect the SST connector to the airbag.

SST
09082-00780  



e.
C106886
2.552,1.448 2.865,1.771 0.313,0.323 10 false *1 2.552,0.302 2.885,0.615 0.333,0.313 10 false *1
*1 Tire
(2 or more)


Place the tires.

i.

Place at least 2 tires under the tire to which the airbag is tied.


ii.

Place at least 2 tires on top of the tire to which the airbag is tied. The top tire should have a disc wheel installed.

NOTICE:
·

Do not place the SST connector under the tire as the connector may be damaged.

·

As the disc wheel may be damaged by the airbag deployment, use a disc wheel that you are planning to throw away.

·

As the tires may be damaged by the airbag deployment, use tires that you are planning to throw away.




iii.
C107328

Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. If there is slack in a wire harnesses, the tires may come loose when the airbag is deployed.




f.
C107076
2.646,1.396 2.458,0.323 2.458,0.323 1.646,0.323 true 1.625,1.667 1.406,1.667 true 1.635,1.583 1.938,1.865 0.302,0.281 10 false *2 0.156,1.896 0.667,2.271 0.51,0.375 10 false SST 1.49,2.573 1.771,2.875 0.281,0.302 10 false *a 1.49,0.24 1.802,0.531 0.313,0.292 10 false *1
*1 Instrument Panel Passenger Airbag
*2 Battery
*a 10 m or more


Connect SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



g.

Deploy the airbag.

i.

Connect the SST red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the airbag.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:

When deploying the airbag, make sure that no one is near the tires.


HINT:

The airbag is deployed as the SST activation switch LED illuminates.




h.
H041436

Dispose of the instrument panel passenger airbag assembly.

CAUTION:
·

The airbag becomes extremely hot when it is deployed. Do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a deployed airbag.

·

Do not apply water to a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the airbag from the tire.


ii.

Place the airbag in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.