Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1880E _58 Vehicle Interior _013242 SUPPLEMENTAL RESTRAINT SYSTEMS _0068641 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light does not Come ON  


DESCRIPTION

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF CONNECTOR

NG

REPLACE OR RECHARGE BATTERY

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the combination meter.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK COMBINATION METER ASSEMBLY

NG

CONNECT CONNECTOR PROPERLY

3.CHECK COMBINATION METER ASSEMBLY
a.

Disconnect the G19 connector from the combination meter.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


H100390
1.479,0.51 1.896,0.76 0.417,0.25 0.5,1.729 0.667,1.406 true 0.948,1.729 0.802,1.417 true 0.125,0.073 0.469,0.406 0.344,0.333 10 false *a 1.563,0.552 2.01,0.865 0.448,0.313 10 false G19 0.344,1.729 0.792,2.042 0.448,0.313 10 false IG+ 0.979,1.719 1.323,2 0.344,0.281 10 false EP
*a Front view of wire harness connector
(to Combination Meter)


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G19-21 (IG+) - Body ground Ignition switch ON 11 to 14 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-22 (EP) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SRS WARNING LIGHT (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SRS WARNING LIGHT (OPERATION)
a.

Connect the connector to the combination meter.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Check the SRS warning light condition.

NOTICE:

Make sure that nobody is in the vehicle.


OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

5.REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

5.REPLACE CENTER AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.



d.

Check the SRS warning light condition.

OK:

SRS warning light illuminates normally.



Result:
Proceed to
OK
NG



OK

END (CENTER AIRBAG SENSOR IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY