Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068660 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  23  Pressure Switch Circuit  


DESCRIPTION

E113418
1.177,0.865 2.406,1.198 1.229,0.333 10 false Low-pressure Side 0.698,1.385 0.958,1.573 0.26,0.188 10 false On 4.49,0.844 5.781,1.104 1.292,0.26 10 false High-pressure Side 1.323,2.135 3.333,2.406 2.01,0.271 10 false 0.196 MPa 4.875,2.146 6.5,2.417 1.625,0.271 10 false 3.14 MPa 0.688,1.99 0.958,2.208 0.271,0.219 10 false Off 0.125,0.125 3.542,0.438 3.417,0.313 12 false Air Conditioner Pressure Sensor Condition: 1.333,2.292 3.344,2.563 2.01,0.271 10 false (2.0 kgf/cm2, 28 psi) 4.885,2.323 6.521,2.573 1.635,0.25 10 false (32.0 kgf/cm2, 455 psi)

The air conditioner pressure sensor turns off when the air conditioning refrigerant pressure extremely (0.196 MPa [2.0 kgf/cm2], 28 psi] or less) or extremely high (3.14 MPa [32.0 kgf/cm2, 455 psi] or more). When the air conditioning amplifier assembly detects the off state of the air conditioner pressure sensor, the air conditioning amplifier assembly outputs signals to the magnet clutch relay to turn the magnet clutch off.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
23 Pressure Switch Circuit When either condition below is met:
·

An open in pressure switch circuit

·

Abnormal refrigerant pressure:

0.196 MPa (2.0 kgf/cm2, 28 psi) or less

3.14 MPa (32.0 kgf/cm2, 455 psi) or high



·

Air conditioner tube & accessory assembly (air conditioner pressure sensor)

·

Refrigerant and refrigerant pipe line

·

Air conditioning amplifier assembly

·

Harness or connector


- -

HINT:

Memory: The air conditioning amplifier stores the DTC of the respective malfunction that has been detected for the period of time indicated in parentheses.


WIRING DIAGRAM

E235395
0.823,3.427 0.99,3.427 false 0.865,3.469 0.958,3.469 false 0.885,3.51 0.938,3.51 false 1.417,3.156 4.25,3.51 2.833,0.354 10 false Air Conditioner Tube & Accessory Assembly (Air Conditioner Pressure Sensor) 5.552,2.625 5.906,2.792 0.354,0.167 10 false PSW 1.417,2.979 1.719,3.125 0.302,0.146 10 false A16 5.302,2.51 5.458,2.656 0.156,0.146 10 false 5 3.594,2.531 3.719,2.677 0.125,0.146 10 false 2 1.969,2.531 2.094,2.677 0.125,0.146 10 false 1 0.625,2.302 1.344,2.542 0.719,0.24 10 false for RHD: 1.417,1.49 4.25,1.844 2.833,0.354 10 false Air Conditioner Tube & Accessory Assembly (Air Conditioner Pressure Sensor) 5.552,0.948 5.906,1.115 0.354,0.167 10 false PSW 5.208,3.938 5.594,4.083 0.385,0.146 10 false G95 1.417,1.323 1.719,1.469 0.302,0.146 10 false A66 5.302,0.844 5.458,0.99 0.156,0.146 10 false 5 2.188,0.854 2.385,1 0.198,0.146 10 false -S 3.313,0.865 3.51,1.01 0.198,0.146 10 false -S 3.594,0.854 3.719,1 0.125,0.146 10 false 4 1.969,0.854 2.094,1 0.125,0.146 10 false 1 5.208,4.104 6.844,4.552 1.635,0.448 10 false Air Conditioning Amplifier Assembly 0.625,0.635 1.344,0.875 0.719,0.24 10 false for LHD:

PROCEDURE

1.CHECK REFRIGERANT PRESSURE
a.

Install a manifold gauge.


b.

Check refrigerant pressure.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>ON-VEHICLE INSPECTION

Standard pressure:

Pressure on high-pressure side

1.37 to 1.57 MPa (13.9 to 16.0 kgf/cm2, 198 to 228 psi)



HINT:

If the refrigerant pressure is below 0.196 MPa (2.0 kgf/cm2, 28 psi), the refrigerant amount in the air conditioning cycle may have decreased significantly due to gas leakage or other problems.


Result:
Proceed to
OK
NG



OK

2.CHECK AIR CONDITIONING OPERATION

NG

CHECK REFRIGERANT AND REFRIGERANT PIPE LINE

2.CHECK AIR CONDITIONING OPERATION
E235399
0.323,0.833 0.793,1.085 0.469,0.252 0.412,0.842 0.692,1.02 0.279,0.179 10 A66 0.811,2.154 1.056,2.385 0.245,0.232 10 *B 0.323,2.294 0.793,2.546 0.469,0.252 0.412,2.302 0.692,2.481 0.279,0.179 10 A16 0.164,0.0 0.529,0.232 0.365,0.232 10 *a 0.811,0.651 1.056,0.883 0.245,0.232 10 *A 2.416,0.363 2.661,0.595 0.245,0.232 10 +S 2.445,1.573 2.735,1.804 0.29,0.232 10 -S 2.404,1.684 1.869,1.248 false 2.385,0.488 1.85,0.923 false
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)


a.

for LHD:

i.

Disconnect the A66 air conditioner pressure sensor connector.


ii.

Using a service wire, connect terminals 1 (+S) and 4 (-S) of the connector on the vehicle wire harness side.


iii.

Start the engine.


iv.

Turn the A/C switch on and check the magnet clutch.



OK:

With terminals 1 (+S) and 4 (-S) connected, magnet clutch is on.

With terminals 1 (+S) and 4 (-S) disconnected, magnet clutch is off.


b.

for RHD:

i.

Disconnect the A16 air conditioner pressure sensor connector.


ii.

Using a service wire, connect terminals 1 and 2 of the connector on the vehicle wire harness side.


iii.

Start the engine.


iv.

Turn the A/C switch on and check the magnet clutch.



OK:

With terminals 1 and 2 connected, magnet clutch is on.

With terminals 1 and 2 disconnected, magnet clutch is off.


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING TUBE & ACCESSORY ASSEMBLY (AIR CONDITIONER PRESSURE SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER AND BODY GROUND)
a.

for LHD:

i.

Disconnect the A66 air conditioner pressure sensor connector.


ii.

Disconnect the G95 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.



Standard Resistance:
Tester Connection Condition Specified Condition
G95-5 (PSW) - A66-4 (-S) Always Below 1 Ω
A66-1 (+S) - Body ground
G95-5 (PSW) - Body ground Always 10 kΩ or higher


b.

for RHD:

i.

Disconnect the A16 air conditioner pressure sensor connector.


ii.

Disconnect the G95 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.



Standard Resistance:
Tester Connection Condition Specified Condition
G95-5 (PSW) - A16-2 Always Below 1 Ω
A16-1 - Body ground
G95-5 (PSW) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (When troubleshooting according to problem symptoms table.) A
OK (When troubleshooting according to DTC.) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR