Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068660 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Heater Relay Circuit  


DESCRIPTION

The heater relay is turned on by signals from the air conditioning amplifier assembly. The heater relay supplies power to the blower motor control.

WIRING DIAGRAM

E225442
5.927,0.594 6.292,0.917 0.365,0.323 10 false HR 4.458,0.979 5.521,1.625 1.063,0.646 10 false to Blower Motor Control 4.49,1.875 5.385,3.094 0.896,1.219 10 false to Blower with Fan Motor Sub-assembly 3.396,1.448 3.844,2.313 0.448,0.865 10 false No.1 Heater Relay 1.479,0.75 2.719,1.115 1.24,0.365 10 false ECU-IG&GAUGE 3.125,1.438 3.458,1.781 0.333,0.344 10 false 4 2.927,0.5 3.24,0.802 0.313,0.302 10 false 1 2.927,0.906 3.188,1.219 0.26,0.313 10 false 5 3.667,0.51 3.958,0.813 0.292,0.302 10 false 2 3.677,0.906 3.917,1.188 0.24,0.281 10 false 3 1.875,1.635 2.51,1.969 0.635,0.333 10 false FR HTR 5.615,2.698 6.802,3.438 1.188,0.74 10 false Air Conditioning Amplifier Assembly 5.604,2.552 6.031,2.854 0.427,0.302 10 false G94 5.688,0.51 6,0.823 0.313,0.313 10 false 14 0.469,1.427 1.417,1.865 0.948,0.438 10 false from Battery 0.479,0.573 1.438,1.135 0.958,0.563 10 false from Ignition Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT HEATER RELAY (HTR)
a.

Remove the No. 1 heater relay from the driver side junction block assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY(for Heater)>REMOVAL


b.
B106753
2.5,0.844 2.5,0.563 true 2.865,1.198 3.073,1.198 true 1.865,1.198 1.865,0.917 false 2.49,1.802 2.49,1.521 true 2.135,1.802 2.135,1.219 true 2.479,1.083 1.771,1.083 true 2.458,0.396 2.76,0.708 0.302,0.313 10 false 1 1.677,1.021 1.979,1.333 0.302,0.313 10 false 4 2.104,1.823 2.406,2.135 0.302,0.313 10 false 3 2.469,1.813 2.771,2.125 0.302,0.313 10 false 2 3.115,1.125 3.417,1.438 0.302,0.313 10 false 5 1.281,0.802 1.583,1.115 0.302,0.313 10 false 3 0.823,0.167 1.125,0.479 0.302,0.313 10 false 4 0.323,0.802 0.625,1.115 0.302,0.313 10 false 5 0.333,1.604 0.635,1.917 0.302,0.313 10 false 1 1.292,1.615 1.594,1.927 0.302,0.313 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
3 - 5 10 kΩ or higher
3 - 4 Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HTR RELAY - AIR CONDITIONING AMPLIFIER, BATTERY AND BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (HTR RELAY - AIR CONDITIONING AMPLIFIER, BATTERY AND BODY GROUND)
a.

Remove the HTR relay from the driver side junction block assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY(for Heater)>REMOVAL


b.

Disconnect the G94 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HTR relay terminal 2 - G94-14 (HR) Always Below 1 Ω
HTR relay terminal 2 - Body ground Always 10 kΩ or higher
HTR relay terminal 3 - Body ground Always 10 kΩ or higher
HTR relay terminal 4 - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HTR relay terminal 1 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
HTR relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.
E225456
0.833,0.135 1.25,0.385 0.417,0.25 1.385,1.75 0.802,1.01 true 0.146,0.125 0.49,0.458 0.344,0.333 10 false *a 0.917,0.177 1.26,0.51 0.344,0.333 10 false G94 1.354,1.76 1.719,2.042 0.365,0.281 10 false HR
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G94-14 (HR) - Body ground
·

Ignition switch off

·

Blower switch off


Below 1 V
·

Ignition switch ON

·

Blower switch on (LO level)


Below 1 V
·

Ignition switch ON

·

Blower switch off


11 to 14 V



Result:
Proceed to
OK
NG



OK

NG