Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068660 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  41  Front Air Mix Damper Control Servo Motor Circuit  


DESCRIPTION

The air mix damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the air mix control damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix control damper to any position. As a result, the air mix control damper varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air is as requested.

HINT:

This DTC is also output if the damper and damper link are malfunctioning or unable to move properly. When this DTC is output, confirm that the mechanical parts of the damper and damper link are not defective or damaged.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
41 Front Air Mix Damper Control Servo Motor Circuit The air mix control damper position does not change when the air conditioning amplifier assembly operates the air mix damper servo sub-assembly.
·

Air mix damper servo sub-assembly

·

Air conditioning amplifier assembly

·

Harness or connector


Memorized
(30 sec. or more)
-

HINT:

Memory: The air conditioning amplifier stores the DTC of therespective malfunction that has been detected for theperiod of time indicated in parentheses.


WIRING DIAGRAM

E233156
5.344,0.917 5.75,1.208 0.406,0.292 10 false G95 1.76,0.802 2.021,1.083 0.26,0.281 10 false 2 1.76,1.323 2.042,1.594 0.281,0.271 10 false 3 1.76,1.865 2,2.125 0.24,0.26 10 false 1 1.76,2.406 2.021,2.698 0.26,0.292 10 false 5 1.76,2.917 1.99,3.167 0.229,0.25 10 false 4 5.344,1.427 5.719,1.719 0.375,0.292 10 false G95 5.396,1.229 5.688,1.51 0.292,0.281 10 false 23 5.396,0.729 5.688,1 0.292,0.271 10 false 24 5.344,1.958 5.708,2.271 0.365,0.313 10 false G95 5.385,1.771 5.688,2.094 0.302,0.323 10 false 20 5.344,2.479 5.729,2.771 0.385,0.292 10 false G94 5.396,2.292 5.677,2.573 0.281,0.281 10 false 17 5.333,3.01 5.708,3.292 0.375,0.281 10 false G94 5.396,2.844 5.688,3.135 0.292,0.292 10 false 19 5.729,0.938 6.125,1.25 0.396,0.313 10 false PMA 0.25,3.458 0.688,3.781 0.438,0.323 10 false G81 5.708,1.438 6.146,1.76 0.438,0.323 10 false PMB 5.719,1.979 6.177,2.302 0.458,0.323 10 false SG-1 5.719,2.5 6.198,2.833 0.479,0.333 10 false AMH 5.708,3.01 6.156,3.313 0.448,0.302 10 false AMC 1.344,0.813 1.844,1.115 0.5,0.302 10 false MCP 1.333,1.323 1.792,1.625 0.458,0.302 10 false MHP 1.427,1.854 1.802,2.146 0.375,0.292 10 false SG 1.344,2.406 1.781,2.729 0.438,0.323 10 false MHD 1.344,2.927 1.792,3.292 0.448,0.365 10 false MCD 5.385,3.469 6.99,4.25 1.604,0.781 10 false Air Conditioning Amplifier Assembly 0.25,3.646 2.521,4.104 2.271,0.458 10 false Air Mix Damper Servo Sub-assembly

PROCEDURE

1.PERFORM ACTUATOR CHECK
a.

Warm up the engine.



c.

Place your hand in front of a vent and check that the air mix control damper position changes (the temperature of the air changes) according to the display code.

Display Code Air Mix Control Damper Position
0 COLD side (0% open)
1 COLD side (0% open)
2 COLD side (0% open)
3 COLD side (0% open)
4 COLD/HOT (50% open)
5 COLD/HOT (50% open)
6 HOT side (100% open)
7 HOT side (100% open)
8 HOT side (100% open)
9 HOT side (100% open)

OK:

Air mix control damper position changes in accordance with each display code.


HINT:

The progression through the steps of the actuator check can be changed from automatic to manual by pressing the front DEF switch.


Result:
Result Proceed to
OK (When troubleshooting according to problem symptoms table.) A
OK (When troubleshooting according to DTC.) B
NG C




A

B

C

2.CHECK HARNESS AND CONNECTOR (AIR MIX DAMPER SERVO - AIR CONDITIONING AMPLIFIER)
2.CHECK HARNESS AND CONNECTOR (AIR MIX DAMPER SERVO - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the G81 air mix damper servo sub-assembly connector.


b.

Disconnect the G94 and G95 air conditioning amplifier assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-5 (MHD) - G94-17 (AMH) Always Below 1 Ω
G81-4 (MCD) - G94-19 (AMC)
G81-3 (MHP) - G95-23 (PMB)
G81-2 (MCP) - G95-24 (PMA)
G81-1 (SG) - G95-20 (SG-1)
G81-1 (SG) - Body ground Always 10 kΩ or higher
G81-2 (MCP) - Body ground
G81-3 (MHP) - Body ground
G81-4 (MCD) - Body ground
G81-5 (MHD) - Body ground



Result:
Proceed to
OK
NG



OK

3.REPLACE AIR MIX DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE AIR MIX DAMPER SERVO SUB-ASSEMBLY
a.

Temporally replace the air mix damper servo sub-assembly with a new or normally functioning one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY


b.

Check the air mix control damper operates normally.

OK:

Air mix control damper operates normally.



Result:
Proceed to
OK
NG



OK

END (AIR MIX DAMPER SERVO IS DEFECTIVE)

NG