Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING
RM1880E _58 Vehicle Interior _013247 INTERIOR PANELS / TRIM _0068695 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL REAR NO. 3 SIDE RAIL SPACER LH

a.

Attach the 3 claws to install the rear No. 3 side rail spacer.


Hide 2.INSTALL REAR NO. 3 SIDE RAIL SPACER LH

a.

Attach the 3 claws to install the rear No. 3 side rail spacer.


Hide 3.INSTALL REAR NO. 3 SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 4.INSTALL REAR NO. 2 SIDE RAIL SPACER LH

HINT:

Use the same procedure for all rear No. 2 side rail spacers.


a.

Attach the 2 claws to install the rear No. 2 side rail spacer.


Hide 5.INSTALL REAR NO. 2 SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 6.INSTALL SIDE RAIL SPACER (for LHD)

a.

Attach the 2 claws to install the side rail spacer.


Hide 7.INSTALL SIDE RAIL SPACER (for RHD)

HINT:

Use the same procedure described for the LHD.


Hide 8.INSTALL FRONT SIDE RAIL SPACER LH

a.

Attach the 3 claws to install the front side rail spacer.


Hide 9.INSTALL FRONT SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 10.INSTALL ROOF HEADLINING ASSEMBLY

B279287

a.

Place the roof headlining into the vehicle as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when placing it.



b.

Attach the 4 fasteners to install the roof headlining.


c.

Install the 8 clips.

B291507
3.823,0.115 4.188,0.448 0.365,0.333 10 false *B 0.292,0.104 0.708,0.438 0.417,0.333 10 false *A
*A for LHD *B for RHD



d.

Connect the connectors and attach the 5 clamps to the front pillar.


Hide 11.INSTALL ASSIST GRIP

HINT:

Use the same procedure for all assist grips.


a.

Install the assist grip with the 2 screws.


b.

Attach the 4 claws and close the 2 covers.


Hide 12.INSTALL VISOR HOLDER LH

a.

Attach the 2 claws to install the visor holder.


b.

Install the screw.


Hide 13.INSTALL VISOR HOLDER RH

HINT:

Use the same procedure described for the LH side.


Hide 14.INSTALL VISOR ASSEMBLY LH

a.

Install the visor with the 2 screws.


b.

Attach the guide.


Hide 15.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 19.INSTALL MAP LIGHT ASSEMBLY (w/ Map Light)

Hide 20.INSTALL INNER UPPER ROOF SIDE GARNISH LH

a.

Attach the 5 clips to install the inner upper roof side garnish.


b.

Connect the rear No. 2 seat belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Attach the 2 claws to close the rear No. 2 seat belt shoulder anchor cover.


Hide 21.INSTALL INNER UPPER ROOF SIDE GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 22.INSTALL QUARTER PILLAR GARNISH LH

a.

Attach the 3 clips to install the quarter pillar garnish.


b.

Connect the rear No. 1 seat belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Attach the 2 claws to close the rear No. 1 seat belt shoulder anchor cover.


Hide 23.INSTALL QUARTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 24.INSTALL QUARTER INSIDE TRIM BOARD LH

a.

Attach the 4 claws, 8 clips and 2 guides to install the quarter inside trim board.


b.

Install the clip.


c.

Connect the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Connect the rear No. 2 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 25.INSTALL QUARTER INSIDE TRIM BOARD RH

a.

Attach the 4 claws, 8 clips and 2 guides to install the quarter inside trim board.


b.

Install the clip.


c.

Connect the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Connect the rear No. 2 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 26.INSTALL QUARTER TRIM HOOK

HINT:

Use the same procedure for both quarter trim hooks.


a.

Install the quarter trim hook with the screw.


Hide 27.INSTALL BACK DOOR SCUFF PLATE

a.

Attach the 6 clips and 4 claws to install the back door scuff plate.


Hide 28.INSTALL CENTER PILLAR GARNISH LH

a.

Attach the guide and clip to install the center pillar garnish.


b.

Connect the front seat belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Attach the 4 claws to install the front seat belt shoulder anchor cover.


Hide 29.INSTALL CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 30.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Attach the 2 claws to install the lower center pillar garnish.


b.

Connect the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 31.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 32.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

B279292
0.938,1.469 1.167,1.26 1.167,1.26 1.302,1.26 false 1.396,1.177 1.813,1.49 0.417,0.313 10 false *1 2.281,0.406 2.667,0.729 0.385,0.323 10 false *2 1.073,0.865 1.5,1.156 0.427,0.292 10 false *2
*1 Paint Mark
*2 Mark Position


a.

Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the rear door opening trim weatherstrip as shown in the illustration.


Hide 33.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 34.INSTALL REAR DOOR SCUFF PLATE LH

a.

Attach the 3 clips and 7 claws to install the rear door scuff plate.


Hide 35.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 36.INSTALL FRONT DOOR OPENING TRIM LH

B279290
2.938,1.385 3.073,1.25 3.073,1.25 3.146,1.25 false 3.188,1.167 3.427,1.396 0.24,0.229 10 false *1 1.552,0.427 1.979,0.771 0.427,0.344 10 false *2 2.427,0.823 2.906,1.167 0.479,0.344 10 false *2
*1 Paint Mark
*2 Mark Position


a.

Align the paint mark on the front door opening trim with the mark position on the vehicle and install the front door opening trim as shown in the illustration.


Hide 37.INSTALL FRONT DOOR OPENING TRIM RH

HINT:

Use the same procedure described for the LH side.


Hide 38.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Attach the 3 clips and 7 claws to install the front door scuff plate.


Hide 39.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 40.INSTALL FRONT PILLAR GARNISH LH

a.

Attach the 3 clips to install the front pillar garnish.


Hide 41.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 42.INSTALL LOWER FRONT PILLAR GARNISH LH

a.

Attach the 3 claws and 3 guides to install the lower front pillar garnish.


Hide 43.INSTALL LOWER FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 44.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).