Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2012.09
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068707 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Apply Primer G to the glass where the stoppers will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Install 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.

B084568
1.458,1.292 1.135,0.573 1.135,0.573 0.938,0.573 true 5.688,1.292 6.01,0.573 6.01,0.573 6.208,0.573 true 0.125,0.104 0.417,0.427 0.292,0.323 10 false *a 1.385,0.74 1.76,1.021 0.375,0.281 10 false *b 0.719,0.5 1.083,0.823 0.365,0.323 10 false *1 1.177,1.833 1.458,2.115 0.281,0.281 10 false b 5.896,1.854 6.208,2.125 0.313,0.271 10 false b 2.125,1.25 2.448,1.531 0.323,0.281 10 false a 4.958,1.25 5.24,1.615 0.281,0.365 10 false a 5.625,0.781 5.927,1.156 0.302,0.375 10 false *b 6.323,0.49 6.698,0.854 0.375,0.365 10 false *1
*1 Ceramic Notch - -
*a Backside *b Center


Standard measurement:
Area Specified Condition
a 7.7 mm (0.303 in.)
b 40.0 mm (1.575 in.)



Hide 2.INSTALL NO. 1 WINDSHIELD GLASS STOPPER

B342540
1.833,0.469 2.281,0.469 false 0.292,1.448 0.292,1 0.292,1 0.542,1 false 1.635,0.396 1.969,0.688 0.333,0.292 10 false *1 0.219,1.5 0.531,1.771 0.313,0.271 10 false *2
*1 Vehicle Body
*2 Stopper


a.

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.


Hide 3.INSTALL NO. 2 WINDOW GLASS ADHESIVE DAM

a.

Apply Primer G to the glass where the No. 2 window glass adhesive dams will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from a new No. 2 window glass adhesive part of the dam. Install the No. 2 window glass adhesive dam (adhesive side) to the glass (Primer G area), but exclude the spacer area as shown in the illustration.

B282354
5.417,0.667 5.5,0.417 5.5,0.417 5.583,0.417 true 4.208,0.656 4.167,0.417 4.167,0.417 4.083,0.417 true 4.969,2.229 5.083,2.417 5.083,2.417 5.167,2.417 true 0.719,0.625 1.073,0.927 0.354,0.302 10 false A 2.021,0.615 2.323,0.917 0.302,0.302 10 false B 1.177,1.052 1.594,1.323 0.417,0.271 10 false C 1.167,0.698 1.583,1.083 0.417,0.385 10 false C 2.677,0.313 3.094,0.604 0.417,0.292 10 false A 4.125,1.573 4.688,1.938 0.563,0.365 10 false C - C 4.99,0.313 5.344,0.677 0.354,0.365 10 false B 5.604,0.333 5.875,0.594 0.271,0.26 10 false *1 5.188,2.333 5.688,2.667 0.5,0.333 10 false *2 0.125,0.094 0.542,0.438 0.417,0.344 10 false *a 5.031,1.625 5.427,1.917 0.396,0.292 10 false a 3.927,0.333 4.135,0.573 0.208,0.24 10 false *1
*1 Ceramic Notch *2 Dam Reference Line
*a Backside - -


Standard measurement:
Area Specified Condition
a 7.0 mm (0.276 in.)



Hide 4.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Apply Primer G to the glass where the glass adhesive dams will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from the adhesive part of a new window glass adhesive dam. Install the window glass adhesive dam (adhesive side) to the glass (Primer G area), but exclude the spacer area as shown in the illustration.

B251146
0.865,2.094 0.865,2.333 true 3.146,0.688 3.198,0.406 3.198,0.406 3.323,0.406 true 6.448,0.688 6.385,0.396 6.385,0.396 6.271,0.396 true 3.604,2.208 3.677,2.427 3.677,2.427 3.74,2.427 true 6,2.177 5.833,1.865 5.833,1.865 5.656,1.865 false 0.708,0.51 1.156,0.938 0.448,0.427 10 false A 2.01,0.51 2.271,0.865 0.26,0.354 10 false B 2.74,1.573 2.958,1.885 0.219,0.313 10 false C 2.375,1.688 2.677,1.969 0.302,0.281 10 false C 0.198,1.073 0.438,1.365 0.24,0.292 10 false C 0.542,1.167 0.802,1.427 0.26,0.26 10 false C 1.104,1.875 1.344,2.094 0.24,0.219 10 false D 1.104,2.25 1.438,2.563 0.333,0.313 10 false D 2.781,0.396 3.073,0.667 0.292,0.271 10 false A 4.938,0.396 5.229,0.667 0.292,0.271 10 false B 3.104,1.542 3.656,1.781 0.552,0.24 10 false C - C 5.198,1.542 5.74,1.875 0.542,0.333 10 false D - D 3.375,0.354 3.698,0.594 0.323,0.24 10 false *1 6.104,0.344 6.396,0.594 0.292,0.25 10 false *1 3.781,2.344 4.073,2.563 0.292,0.219 10 false *2 5.469,1.771 5.781,2.052 0.313,0.281 10 false *2 3.927,1.708 4.208,2.021 0.281,0.313 10 false a 0.781,2.385 1.094,2.656 0.313,0.271 10 false *2 0.146,0.135 0.458,0.458 0.313,0.323 10 false *a
*1 Ceramic Notch *2 Dam Reference Line
*a Backside - -


Standard measurement:
Area Specified Condition
a 7.0 mm (0.276 in.)



Hide 5.INSTALL WINDSHIELD GLASS

B106104
1.802,0.479 2.135,0.24 2.135,0.24 1.792,0.781 true 2.146,0.083 2.552,0.375 0.406,0.292 10 false *1
*1 Matchmark


a.

Position the windshield glass.

i.

Using suction cups, place the glass in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.

HINT:
·

Placing matchmarks is only necessary when installing new windshield glass. If it the windshield glass is being reused, matchmarks should already be present.

·

When reusing the windshield glass, check and correct the matchmark positions.



NOTICE:

Check that the stoppers are attached to the vehicle body correctly.



iv.

Using suction cups, remove the windshield glass.



b.
B106085
2.302,2.281 1.896,2.281 true 2.417,1.115 1.917,0.771 false 2.344,2.177 1.844,1.833 true 2.156,0.24 2.417,0.5 0.26,0.26 10 false *a 1.729,0.656 2.104,0.906 0.375,0.25 10 false *1 1.625,1.708 1.875,1.938 0.25,0.229 10 false *1 0.552,4.385 0.833,4.583 0.281,0.198 10 false *1 1.688,2.188 1.948,2.49 0.26,0.302 10 false *2 2.25,2.406 2.583,2.667 0.333,0.26 10 false *b
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT


Using a brush, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Using a brush or sponge, apply Primer G to the contact surface of the glass.

B282355
2.979,0.646 4.208,2.073 1.229,1.427 4.25,0.646 5.594,2.073 1.344,1.427 5.667,0.646 7.01,2.073 1.344,1.427 2.24,2.021 2.24,2.438 true 3.167,1.344 3.167,1.677 true 4.5,1.344 4.5,1.677 true 6.24,1.344 6.333,1.667 6.333,1.667 6.448,1.344 true 0.104,0.094 0.521,0.438 0.417,0.344 10 false *a 1.042,0.573 1.563,1.083 0.521,0.51 10 false A 2.365,0.563 2.833,0.833 0.469,0.271 10 false A 2.365,0.927 2.667,1.271 0.302,0.344 10 false A 1.052,0.927 1.417,1.26 0.365,0.333 10 false A 1.708,0.573 1.958,0.792 0.25,0.219 10 false B 1.708,0.938 1.958,1.156 0.25,0.219 10 false B 2.458,1.625 2.708,1.844 0.25,0.219 10 false B 2.802,1.531 3.052,1.75 0.25,0.219 10 false B 0.26,1.042 0.615,1.323 0.354,0.281 10 false B 0.594,1.125 0.844,1.344 0.25,0.219 10 false B 1.698,1.792 1.948,2.031 0.25,0.24 10 false C 1.708,2.188 1.958,2.427 0.25,0.24 10 false C 3.052,0.698 3.688,1.031 0.635,0.333 10 false A - A 4.333,0.688 4.938,1.021 0.604,0.333 10 false B - B 5.74,0.688 6.281,0.938 0.542,0.25 10 false C - C 2.156,2.479 2.427,2.729 0.271,0.25 10 false *2 0.563,2.479 0.906,2.677 0.344,0.198 10 false *1 3.104,1.719 3.417,2 0.313,0.281 10 false *2 6.25,1.719 6.573,2.031 0.323,0.313 10 false *2 4.427,1.708 4.698,1.979 0.271,0.271 10 false *2
*1 Primer G *2 Adhesive Center Line
*a Backside - -


HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




d.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the glass as shown in the illustration.

B282356
4.354,0.01 5.688,1.365 1.333,1.354 5.802,0.01 7.146,1.365 1.344,1.354 4.885,1.427 6.365,2.698 1.479,1.271 4.729,0.938 4.729,1.104 true 6.188,0.938 6.188,1.125 true 5.531,2.115 5.635,2.333 5.635,2.333 5.74,2.115 true 1.938,1.719 1.938,1.958 true 0.073,0.083 0.427,0.438 0.354,0.354 10 false *a 2.375,0.271 2.708,0.656 0.333,0.385 10 false A 3.667,0.26 3.896,0.563 0.229,0.302 10 false A 3.667,0.604 4,0.917 0.333,0.313 10 false A 2.354,0.625 2.625,0.885 0.271,0.26 10 false A 3.01,0.271 3.313,0.583 0.302,0.313 10 false B 1.479,0.75 1.802,1 0.323,0.25 10 false B 1.969,0.865 2.198,1.146 0.229,0.281 10 false B 4.094,1.229 4.354,1.479 0.26,0.25 10 false B 3.75,1.313 4.063,1.552 0.313,0.24 10 false B 3.01,0.625 3.323,0.885 0.313,0.26 10 false B 3.021,1.479 3.24,1.75 0.219,0.271 10 false C 3.021,1.885 3.333,2.24 0.313,0.354 10 false C 0.563,1.51 0.865,1.875 0.302,0.365 10 false a 0.156,2.333 0.531,2.625 0.375,0.292 10 false a 0.531,1.948 0.865,2.271 0.333,0.323 10 false b 1,1.594 1.271,1.896 0.271,0.302 10 false b 4.656,1.156 4.969,1.458 0.313,0.302 10 false *2 4.417,0.042 5.01,0.302 0.594,0.26 10 false A - A 5.854,0.042 6.333,0.292 0.479,0.25 10 false B - B 4.948,1.469 5.5,1.688 0.552,0.219 10 false C - C 4.667,0.25 4.948,0.5 0.281,0.25 10 false c 6.115,0.24 6.438,0.49 0.323,0.25 10 false c 5.948,1.458 6.344,1.833 0.396,0.375 10 false d 6.115,1.167 6.438,1.458 0.323,0.292 10 false *2 5.563,2.396 5.74,2.583 0.177,0.188 10 false *2 0.948,2.365 1.26,2.677 0.313,0.313 10 false *1 1.865,2.01 2.26,2.302 0.396,0.292 10 false *2
*1 Adhesive *2 Adhesive Center Line
*a Backside - -


Standard measurement:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 3.0 mm (0.118 in.)
d 18.3 mm (0.720 in.)




e.
B106104
1.802,0.479 2.135,0.24 2.135,0.24 1.792,0.781 true 2.146,0.083 2.552,0.375 0.406,0.292 10 false *1
*1 Matchmark


Install the windshield glass to the vehicle body.

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned. Press it in gently along the rim.


ii.

Lightly press the outer surface of the windshield glass to ensure that it is securely fit to the vehicle body.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and windshield glass have a small gap between them.




iii.

Hold the windshield glass in place securely with protective tape or equivalent until the adhesive hardens.



Hide 6.INSTALL WINDSHIELD OUTSIDE MOULDING

B284081

a.

Using a brush or sponge, apply Primer G to the glass where a new windshield outside moulding will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Install a new windshield outside moulding before the adhesive dries.

NOTICE:

Do not drive the vehicle for the amount of time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours



Hide 9.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 14.INSTALL MAP LIGHT ASSEMBLY (w/ Map Light)

Hide 19.INSTALL FRONT DOOR OPENING TRIM LH

Install the front door opening trim LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).

Hide 20.INSTALL FRONT DOOR OPENING TRIM RH

HINT:

Use the same procedure described for the LH side.


Hide 21.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Wipe off any tape with cleaner.



b.
B284080
1.594,0.729 2.229,0.51 2.229,0.51 1.792,0.823 true 2.302,0.375 2.646,0.677 0.344,0.302 10 false *1
*1 Double-sided Tape


Install a new front fender to cowl side seal LH.

i.

Using a heat light, heat the vehicle body and seal.


ii.

Remove the peeling paper from the face of the seal.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Attach the 3 claws to install the front fender to cowl side seal LH.



Hide 22.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 23.INSTALL COWL TOP VENTILATOR LOUVER LH

Hide 24.INSTALL COWL TOP VENTILATOR LOUVER RH

Hide 26.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 27.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH