Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1.REMOVE FRONT WIPER ARM HEAD CAP
2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
4.REMOVE HOOD TO COWL TOP SEAL
5.REMOVE COWL TOP VENTILATOR LOUVER RH
6.REMOVE COWL TOP VENTILATOR LOUVER LH
7.REMOVE FRONT FENDER TO COWL SIDE SEAL LH
| *1 | Double-sided Tape |
Using a heat light, heat the seal.
20 to 30°C (68 to 86°F)
Do not heat the seal excessively.
Using a screwdriver, detach the double-sided tape (2 areas) and remove the front fender to cowl side seal LH.
Be careful not to damage the vehicle body.
Tape the screwdriver tip before use.
8.REMOVE FRONT FENDER TO COWL SIDE SEAL RH
Use the same procedure described for the LH side.
9.REMOVE FRONT DOOR OPENING TRIM LH
Partially remove the front door opening trim weatherstrip LH so that the front pillar garnish LH can be removed (see page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).
10.REMOVE FRONT DOOR OPENING TRIM RH
Use the same procedures described for the LH side.
11.REMOVE LOWER FRONT PILLAR GARNISH LH
12.REMOVE LOWER FRONT PILLAR GARNISH RH
13.REMOVE FRONT PILLAR GARNISH LH
14.REMOVE FRONT PILLAR GARNISH RH
15.REMOVE MAP LIGHT ASSEMBLY
16.REMOVE VISOR ASSEMBLY LH
17.REMOVE VISOR ASSEMBLY RH
18.REMOVE VISOR HOLDER LH
19.REMOVE VISOR HOLDER RH
20.REMOVE INNER REAR VIEW MIRROR ASSEMBLY
21.REMOVE ASSIST GRIP
22.REMOVE ROOF HEADLINING ASSEMBLY
Partially remove the roof headlining assembly (see page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).
It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining.
23.REMOVE WINDSHIELD OUTSIDE MOULDING
| *1 | Windshield Outside Moulding |
| *a | Cut |
Using a knife, cut off the moulding as shown in the illustration.
Be careful not to damage the vehicle body.
Remove the remaining moulding.
Make a partial cut in the moulding. Then pull and remove it by hand.
24.REMOVE WINDSHIELD GLASS
| *1 | Plastic Sheet |
| *2 | Protective Tape |
| *3 | Stopper |
| *4 | Piano Wire |
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.
| *1 | Matchmark |
Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.
Matchmarks do not need to be placed if not reusing the glass.
Cut through the adhesive by pulling the piano wire around the glass.
Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.
Using suction cups, remove the glass.
25.CLEAN WINDSHIELD GLASS
Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.
Clean the outer edges of the glass with non-residue solvent.
Even if using a new glass, clean it with non-residue solvent.
26.CLEAN VEHICLE BODY
| *1 | Adhesive |
| *2 | Vehicle Body |
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
Leave as much adhesive on the vehicle body as possible.
Be careful not to damage the vehicle body.
Clean the contact surface of the vehicle body with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.