Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2012.09
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068707 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 5.REMOVE COWL TOP VENTILATOR LOUVER RH

Hide 6.REMOVE COWL TOP VENTILATOR LOUVER LH

Hide 7.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

B284080
1.594,0.729 2.229,0.51 2.229,0.51 1.792,0.823 true 2.302,0.375 2.646,0.677 0.344,0.302 10 false *1
*1 Double-sided Tape


a.

Using a heat light, heat the seal.

Heating temperature:

20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the seal excessively.



b.

Using a screwdriver, detach the double-sided tape (2 areas) and remove the front fender to cowl side seal LH.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Tape the screwdriver tip before use.



Hide 8.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 9.REMOVE FRONT DOOR OPENING TRIM LH

a.

Partially remove the front door opening trim weatherstrip LH so that the front pillar garnish LH can be removed (see page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 10.REMOVE FRONT DOOR OPENING TRIM RH

HINT:

Use the same procedures described for the LH side.


Hide 11.REMOVE LOWER FRONT PILLAR GARNISH LH

Hide 12.REMOVE LOWER FRONT PILLAR GARNISH RH

Hide 20.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 22.REMOVE ROOF HEADLINING ASSEMBLY

a.

Partially remove the roof headlining assembly (see page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining.



Hide 23.REMOVE WINDSHIELD OUTSIDE MOULDING

B050448
1.823,0.781 2,0.25 2,0.25 2.083,0.25 false 1.583,0.125 1.938,0.344 0.354,0.219 10 false *a 2.646,0.938 2.979,1.188 0.333,0.25 10 false *a 2.135,0.167 2.396,0.458 0.26,0.292 10 false *1
*1 Windshield Outside Moulding
*a Cut


a.

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Remove the remaining moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



Hide 24.REMOVE WINDSHIELD GLASS

B282352
2.333,0.417 2.167,0.417 2.167,0.417 2.167,0.792 false 1.115,1.083 0.75,1.083 0.75,1.083 0.75,1.583 true 0.927,2.74 0.927,3.063 0.927,3.063 2.552,3.063 true 2.552,3.063 2.552,2.74 true 1.75,3.063 1.75,3.208 true 0.896,3.833 1.167,3.833 false 2.385,0.333 2.615,0.552 0.229,0.219 10 false *1 0.688,1.615 1.021,1.927 0.333,0.313 10 false *2 1.208,3.75 1.5,4 0.292,0.25 10 false *4 1.677,3.229 2,3.5 0.323,0.271 10 false *3
*1 Plastic Sheet
*2 Protective Tape
*3 Stopper
*4 Piano Wire


a.

Apply protective tape to the outer surface of the vehicle body to prevent scratches.


b.

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


c.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.




d.
B106095
1.646,1.521 1.094,1.771 1.094,1.771 1.646,1.25 true 0.927,1.698 1.292,1.948 0.365,0.25 10 false *1
*1 Matchmark


Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed if not reusing the glass.



e.

Cut through the adhesive by pulling the piano wire around the glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



f.

Using suction cups, remove the glass.


Hide 25.CLEAN WINDSHIELD GLASS

B106080

a.

Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.


b.

Clean the outer edges of the glass with non-residue solvent.

NOTICE:
Do not touch the glass surface after cleaning it.

Even if using a new glass, clean it with non-residue solvent.



Hide 26.CLEAN VEHICLE BODY

B106081
0.5,1.292 0.75,0.75 0.75,0.75 0.833,0.75 true 2.26,1.438 2.583,0.75 2.583,0.75 2.667,0.75 true 2.427,1.604 2.427,1.781 false 0.813,1.573 0.813,1.76 false 0.865,0.667 1.219,0.917 0.354,0.25 10 false *1 2.698,0.667 3.031,0.927 0.333,0.26 10 false *1 0.729,1.781 1,2 0.271,0.219 10 false *2 2.344,1.802 2.583,2 0.24,0.198 10 false *2
*1 Adhesive
*2 Vehicle Body


a.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.